Circutor Wibeee-3P User manual

INSTRUCTION MANUAL

Consumption analysers

(M064B01-03-20A)

SMART PLUGGING

2

Wibeee

Instruction Manual

3

Instruction Manual

Wibeee

SAFETY PRECAUTIONS

DANGER

Warns of a risk, which could result in personal injury or material damage.

ATTENTION

Indicatesthatspecialattentionshouldbepaidtoaspecicpoint.

Follow the warnings described in this manual with the symbols shown below.

If you must handle the unit for its installation, start-up or maintenance, the following

should be taken into consideration:

Incorrect handling or installation of the unit may result in injury to personnel as well as damage

to the unit. In particular, handling with voltages applied may result in electric shock, which may

cause death or serious injury to personnel. Defective installation or maintenance may also

leadtotheriskofre.

Read the manual carefully prior to connecting the unit. Follow all installation and maintenance

instructions throughout the unit’s working life. Pay special attention to the installation stan-

dards of the National Electrical Code.

Refer to the instruction manual before using the unit

In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can

result in injury or damage to the unit and /or installations.

CIRCUTOR,SAreservestherighttomodifyfeaturesortheproductmanualwithoutpriornotication.

DISCLAIMER

CIRCUTOR, SAreservestherighttomakemodicationstothedeviceortheunitspecica-

tions set out in this instruction manual without prior notice.

CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device

specicationsandthemostupdatedmanuals.   

www.circutor.com

CIRCUTOR, recommends using the original cables and accessories that are

supplied with the device.

4

Wibeee

Instruction Manual

CONTENTS

SAFETY PRECAUTIONS ��3

DISCLAIMER ��3

CONTENTS �� 4

REVISION LOG ��6

SYMBOLS �� 6

1�- VERIFICATIONS UPON RECEPTION ��7

2�- DESCRIPTION OF THE PRODUCT �� 7

3�- INSTALLING THE DEVICE ��8

3�1�- PRELIMINARY RECOMMENDATIONS ��8

3�2�- INSTALLATION ��9

3�3�- DEVICE TERMINALS �� 10

3�3�1�- Wibeee-M-L ��10

3�3�2�- Wibeee-M-R ��10

3�3�3�- Wibeee-T-L �� 11

3�3�4�- Wibeee-T-R �� 11

3�3�5�- Wibeee-3P ��12

3�4�- CONNECTION DIAGRAMS ��12

3�4�1�- Wibeee-M-L ��12

3�4�2�- Wibeee-M-R ��13

3�4�3�- Wibeee-T-L ��13

3�4�4�- Wibeee-T-R ��14

3�4�5�- Wibeee-3P ��14

3�5�- STARTING UP THE DEVICE ��15

3�5�1�- APPLICATION MODE ��15

3�5�2�- DIRECT SHARE MODE ��16

3�6�- CALIBRATION ��17

4�- OPERATION ��18

4�1�- OPERATING PRINCIPLE �� 18

4�2�- MEASUREMENT PARAMETERS ��18

4�2�1�- Wibeee-M-L and Wibeee-M-R ��18

4�2�2�- Wibeee-T-L, Wibeee-T-R and Wibeee-3P �� 19

4�3�- LED INDICATORS ��19

4�4�- BUTTON ��20

4�5�-START-UP ��20

5�- DISPLAY AND CONFIGURATION ��22

5�1�-MOBILE APPLICATION ��22

5�2�- WEB PLATFORM ��23

5�2�1�- HOME ��24

5�2�2�- DASHBOARD ��28

5�2�3�- DEVICES ��29

5�2�4�- NOTIFICATIONS ��29

5�2�5�- REPORTS ��30

5�2�6�- HELP ��32

5�3�- INTERNAL WEB SERVER ��32

5�3�1�- INSTANT DATA��33

5�3�2�- NETWORK ��34

5�3�3�- ADVANCED OPTIONS ��34

5�3�4�- GENERAL OPTIONS ��35

5�4�- CONFIGURATION THROUGH HTTP GET REQUESTS ��35

5�4�1�- PARAMETER QUERY ��35

5�4�2�- CONFIGURATION ��38

6�- WIRELESS COMMUNICATIONS ��40

6�1�- USAGE ENVIRONMENT AND HEALTH �� 40

6�2�- Wi-Fi COMMUNICATIONS ��40

6�3�- MODBUS TCP PROTOCOL ��40

6�4�- MODBUS MEMORY MAP ��41

7�- TECHNICAL FEATURES ��43

8�- MAINTENANCE AND TECHNICAL SERVICE ��46

5

Instruction Manual

Wibeee

9�- WARRANTY ��46

10�- CE CERTIFICATE �� 47

6

Wibeee

Instruction Manual

REVISION LOG

Table 1: Revision log�

Date Revision Description

01/18 M064B01-03-18A Initial Version

08/18 M064B01-03-18B

Changes in the following sections:

7

02/20 M064B01-03-20A

Changes in the following sections:

2.- 3.5. - 5.2.1.1.

Note: The images of the devices are for illustration purposes only and may differ from the orig-

inal device.

SYMBOLS

Table 2: Symbols�

Symbol Description

Compliant with the relevant European standards.

Do not remove from hazardous live conductors or place it around them.

Double insulation.

~

AC current.

Device covered by European directive 2002/96/EC. At the end of its useful

life, do not leave the device in a household waste container. Follow local

regulations on electronic equipment recycling.

7

Instruction Manual

Wibeee

1�- VERIFICATIONS UPON RECEPTION

The following must be checked upon reception of the device:

 a)Thedevicehasbeensuppliedaccordingtothespecicationsinyourorder.

b) The device has not been damaged during transport.

c) Perform an external visual inspection of the device before connecting it.

d) Check that it has been supplied with the following:

- An installation guide,

- A set of magnets,

2�- DESCRIPTION OF THE PRODUCT

Wibeee is a new method for electrical data acquisition, to facilitate decision making when it

comes to understanding the use of electrical energy. The technology used, which is attached

via a clip, is based on the patented DINZERO system and consists of simply attaching the de-

vice to the cable or to the upper part of an MCB (miniature circuit breaker).

Once switched on, the device will begin to convert the measured parameters into information

that is sent via a wireless connection.

There are 5 models available:

 Wibeee-M-L single-phase model with a neutral connection on the left.

 Wibeee-M-R single-phase model with a neutral connection on the right.

 Wibeee-T-L three-phase model with a neutral connection on the left.

 Wibeee-T-R three-phase model with a neutral connection on the right.

 Wibeee-3P three-phase model with no neutral connection.

The models have:

- 2 indicator LEDs

- 1 Reset button

- Wi-Fi communications

You can access the data measured by the device via the Wibeee Circutor mobile application,

the website http://wibeee�circutor�com, or the device's internal web server.

8

Wibeee

Instruction Manual

3�- INSTALLING THE DEVICE

3.1.- PRELIMINARY RECOMMENDATIONS

In order to use the device safely, it is critical that individuals who handle it follow

the safety measures set out in the standards of the country where it is being used,

use the personal protective equipment necessary (rubber gloves, face protection

andapprovedame-resistantclothing)topreventinjuriesduetoelectricshockor

electric arc due to exposure to current-carrying conductors and pay attention to

the various warnings indicated in this instruction manual.

The Wibeeedevicemustbeinstalledbyauthorisedandqualiedstaff.

Disconnect the device from the power supply and disconnect the measuring devices before

handling, changing the connections or replacing the device. Handling the device while it is con-

nected is hazardous to people nearby.

It is essential to keep the cables in a perfect condition to avoid accidents, personal injury and

damage to installations.

Limittheoperationofthedevicetomeasuringthespeciedcurrentorvoltagevalues.

The manufacturer of the device shall not be held responsible for any damage resulting from the

user or installation company failing to observe the warnings and/or recommendations indicated

in this manual nor for any damage resulting from the use of non-original products or accesso-

ries or those from other brands.

Do not use the device to take measurements if you detect an anomaly or malfunction.

Check the environment in which the device is installed before taking a measurement. Do not

use the device to take measurements in dangerous, explosive, wet or damp environments.

Disconnect the device from the mains and from the power supply (both the device

and its measuring system) before performing any maintenance work, repairs or

handling any of the connections of the device.

Contact the after-sales service if you detect that the device is not working prop-

erly.

9

Instruction Manual

Wibeee

3.2.- INSTALLATION

Before using the Wibeee ensure that the conditions are appropriate for

working, and that the protective equipment is adequate�

Use of the Wibeee on uninsulated conductors is limited to 265 V~ to the

power frequency.

For measuring of uninsulated conductors, use the appropriate and necessary

personal protective equipment.

The device should be installed after the circuit breaker. (Imax: 63 A)

To install the device, carry out the following steps:

1� Remove the protective panel from the electric panel.

Figure 1: Remove the connection panel�

2� When installing the device, make sure that the neutral terminal (N) corresponds with the neu-

tral cable of the installation (your device could be damaged if incorrectly installed).

Place the magnetic connectors in the direction of the circuit breaker and near to the casing of

the Wibeee.

Figure 2: Install the device�

10

Wibeee

Instruction Manual

3� Check that it is secured.

4� Check that the red LED is on and blinking.

5� After a few seconds, the blue LED will start blinking.

3.3.- DEVICE TERMINALS

3�3�1�- Wibeee-M-L

Table 3:List of terminals of the Wibeee-M-L�

Terminals of the Wibeee-M-L device

1: N, Neutral

2: L1, Voltage input

1

2

Figure 3:Wibeee-M-L Terminals�

3�3�2�- Wibeee-M-R

Table 4:List of terminals of the Wibeee-M-R�

Terminals of the Wibeee-M-R device

1: L1, Voltage input

2: N, Neutral

1

2

Figure 4:Wibeee-M-R Terminals�

11

Instruction Manual

Wibeee

3�3�3�- Wibeee-T-L

Table 5:List of terminals of the Wibeee-T-L�

Terminals of the Wibeee-T-L device

1: N, Neutral 3: L2, Voltage input L2

2: L1, Voltage input L1 4: L3, Voltage input L3

1

2

3

4

Figure 5:Wibeee-T-L Terminals�

3�3�4�- Wibeee-T-R

Table 6:List of terminals of the Wibeee-T-R�

Terminals of the Wibeee-T-R device

1: L1, Voltage input L1 3: L3, Voltage input L3

2: L2, Voltage input L2 4: N, Neutral

1

2

3

4

Figure 6:Wibeee-T-R Terminals�

12

Wibeee

Instruction Manual

3�3�5�- Wibeee-3P

Table 7:List of terminals of the Wibeee-3P�

Terminals of the Wibeee-3P device

1: L1, Voltage input L1 3: L3, Voltage input L3

2: L2, Voltage input L2

1

2

3

L2

L3

Figure 7:Wibeee-3P Terminals�

3.4.- CONNECTION DIAGRAMS

3�4�1�- Wibeee-M-L

N L

Figure 8: Wibeee-M-L connection diagram�

13

Instruction Manual

Wibeee

3�4�2�- Wibeee-M-R

N

L

Figure 9: Wibeee-M-R connection diagram�

3�4�3�- Wibeee-T-L

N L1 L2 L3

Figure 10: Wibeee-T-L connection diagram�

14

Wibeee

Instruction Manual

3�4�4�- Wibeee-T-R

N

L1

L2

L3

Figure 11: Wibeee-T-R connection diagram�

3�4�5�- Wibeee-3P

L1 L2 L3

Figure 12: Wibeee-3P connection diagram�

15

Instruction Manual

Wibeee

3.5.- STARTING UP THE DEVICE

To start communication with the device it is necessary:

1�- To have access to the Internet through a wireless network.

2�- To check that the following ports are open:

- Port 8080 for Http Get / Post.

- Port 53 for DNS

- Port 80 for Internet

Note: The Orange Livebox Next router is incompatible with Wibeee devices when in “WPA/

WPA2” security mode and they do not connect. When in “only WPA2” mode they connect cor-

rectly.

Note: For the correct functioning of the Wibeee, it is necessary to connect it to one of the rst

11 Wi-Fi channels.

The Wibeee's data can be accessed in two ways:

 Application mode.

 Direct share mode.

3�5�1�- APPLICATION MODE

In application mode, the data measured by the Wibeee is uploaded to the cloud and accessed

using the Wibeee CIRCUTOR application. When using this mode, the Wibeee and the user

whohascongureditarelinked,sotheusercancontrolthedevice,viewthedatathathasbeen

sent and the charts and manage groups of devices.

To start the device in application mode, follow these steps:

1�- Scan the QR code to download the application or download it from:

http://wibeee�circutor�com

2�- Open the Wibeee CIRCUTOR application. And follow the steps that it indicates.

16

Wibeee

Instruction Manual

3�5�2�- DIRECT SHARE MODE

In direct share mode the Wibeee's data is directly accessed from the device's integrated web

server, so you can view the measurements being captured at that moment in real time and

manuallycongurethedevice.Thisallowsyoutochangeparameters,suchastheserverand

port to which the Wibeee willsendthedata.IfyoucongureaWibeee while using this mode,

there is no link between the user and the device, so the only way to access the device when it

is connected to the network is by knowing its IP address and accessing it using a search tool.

To start the device in direct share mode, follow these steps:

1�- On a smartphone/tablet, use the Wi-Fi connection's settings to connect to the Wibeee�

2�-Youcangetaccesstothenetcongurationandinstantmeasurementsthroughyourbrows-

er, at the address: http://192�168�1�150

User: user

Password: user

17

Instruction Manual

Wibeee

3.6.- CALIBRATION

When the device has been installed and started, it needs to be calibrated.

The calibration process appears automatically in the Wibeee Circutor mobile application dur-

ing installation.

Follow these steps:

1�- When the device has been successfully installed, measure the current of the L1 with a cur-

rent clamp, and enter the value on the calibration screen, Figure 13.

Note: calibration should be performed when the device has a current ow of 5 ... 10 A.

Figure 13: Calibration screen�

2�- Repeat the calibration process for each of the device's measurement cables.

If you skip the calibration process while installing the device, the accuracy of

the measurements is not guaranteed.

If the measurement cables are replaced or moved after calibration has been

performed, it must be repeated. You can calibrate the device again via the

Edit menu.

18

Wibeee

Instruction Manual

4�- OPERATION

4.1.- OPERATING PRINCIPLE

The Wibeee is a power consumption measurement device with a Wi-Fi wireless connection to

display or download the data that is measured, using any smartphone, tablet or PC.

Electrical Panel

Wibeee Laptop PC Smartphone Tablet

Figure 14: Overview

The device can work in two operating modes:

 Application mode

In application mode, the data measured by the Wibeee is uploaded to the cloud and ac-

cessed via the Wibeee CIRCUTOR application or the http://wibeee�circutor�com web

platform.

 Direct share mode

In direct share mode the Wibeee's data is directly accessed from the device's integrated

web server.

Note: The device's integrated web server can also be accessed in the application's operating

mode.

4.2.- MEASUREMENT PARAMETERS

The device measures and logs the following parameters:

4�2�1�- Wibeee-M-L and Wibeee-M-R

Table 8: Measurement parameters of the Wibeee-M-L and Wibeee-M-R�

Parameter Units

Voltage V

Current A

Frequency Hz

Active Power kW

Apparent Power kVA

Inductive Reactive Power kvarL

Capacitive Reactive Power kvarC

Power Factor PF

Active Energy kWh

Reactive Energy kvarh

19

Instruction Manual

Wibeee

Table 8 (Cont�): Measurement parameters of the Wibeee-M-L and Wibeee-M-R�

Parameter Units

Inductive Reactive Energy kvarLh

Capacitive Reactive Energy kvarCh

Cost -

CO

2

Emissions KgCO

2

4�2�2�- Wibeee-T-L, Wibeee-T-R and Wibeee-3P

Table 9: Measurement parameters of the Wibeee-T-L, Wibeee-T-R and Wibeee-3P�

Parameter Units

Phases

L1-L2-L3

Total

Voltage V

 

Current A

 

Frequency Hz

 

Active Power kW

 

Apparent Power kVA

 

Inductive Reactive Power kvarL

 

Capacitive Reactive Power kvarC

 

Power Factor PF

 

Active Energy kWh

 

Reactive Energy kvarh

 

Inductive Reactive Energy kvarLh

 

Capacitive Reactive Energy kvarCh

 

Cost -

 

CO

2

Emissions KgCO

2

 

4.3.- LED INDICATORS

The device has 2 status LEDs, Figure 15 and Table 10.

L2

L3

Blue Red

Figure 15:LED indicators�

20

Wibeee

Instruction Manual

Table 10: Description of the LEDs�

LED Description

Red Blinking light: Powered device.

Blue

Indicates the connection status:

Slow blinking light (1s): Generating a Wi-Fi network.

Fast blinking light (<1s) : Connected to a Wi-Fi network.

Steady light: Data being sent over the network.

4.4.- BUTTON

The device has a Reset button, Figure 16, to restore the device's factory settings (hold it down

for more than 6 seconds).

Reset

L2

L3

Reset

Figure 16:Reset Button�

4.5.-START-UP

During the start-up of the device, the Wibeee goes through different states:

1�- Conguration state

Blue LED→Slowblinkinglight(1s)

Red LED→Slowblinkinglight(1s)

In this state, the Wibeee generates its own Wi-Fi network called WIBEEE_xx:xx:xx�

Itisonlyusedtocongurethedeviceandconnectittotheuser'snetwork.

If you want to return to this state to obtain the initial conditions, you should hold down the Re-

set button for more than 6 seconds. The device deletes any previous settings and restores the

default values.

2�- Connecting�� state

Blue LED→Off

Red LED→Slowblinkinglight(1s)

In this state, the Wibeee is managing the connection with the router/access point.

This state should last for 40 seconds, when there is good Wi-Fi coverage. In places where there

is weak Wi-Fi coverage, it may take longer.

Page is loading ...

Circutor Wibeee-3P User manual

This manual is also suitable for

Circutor Wibeee-3P User manual

Related papers

Other documents