AAMP of Flordia XBD-ISBT3 User manual

Brand: AAMP of Flordia

Model: XBD-ISBT3

Category: Car video systems

Type: User manual

Initial Setup

After this quick setup, you will be ready to enjoy your music wirelessly

1) Charge

Charge your BluJax by connecting it to a USB power supply (USB cable included). When connected to a USB power source the BluJax will glow Red

while charging. When charging is complete, the BluJax will glow Blue.

2) Pair

After charging your BluJax, unplug it from the USB power source.

 IftheBluJaxisglowing,pressthecontrolbuttonfor3secondstoturnitoff.Redlightwillblink3timestoconrmpoweroff.

 Pressandholdthecontrolbuttonfor10seconds(untilbluelightrapidlyashes)toenterPairingmode.

Open the Bluetooth menu on your smartphone or audio source, and search for available Bluetooth accessories.

Select BluJax from the list, and select “connect”. When a successful connection has been established,

 theBluJaxwillconrmbyglowingBlue.

3) Connect

Plug the BluJax into the vehicle’s auxiliary audio input. The 3.5mm jack on the BluJax has been intentionally designed

off-center so that it can be rotated to allow it to clear buttons or other obstructions located near your aux input.

If simply rotating the BluJax is not allowing full insertion into the auxiliary input, we have provided a short extension

cable which can be used to make the connection. Connect the extension cable between the BluJax and the Aux input.

Operation

Whenrstreturningtothevehicle,youwillneedtopressthecontrolbuttononceontheBluJaxtowakeitup.Uponwake-up,theBluelightwillblink

three times, and the BluJax will automatically reconnect with the previously paired Bluetooth device, as long as it is in range. The BluJax will glow blue to

conrmthatitisreconnectedtoyourdevice.

Select the auxiliary audio input source on your radio to enjoy your music.

1) Control Streaming Music Playback

Begin music playback from your paired Bluetooth device

Press button once on the center of the BluJax to toggle Play / Pause of music playback Press button twice skips to the next track

2) Power On / Power Off

To save battery life while not in use, simply press the control button for 3 seconds to turn off the BluJax. The red light will blink 3 times when turning

off. When you are ready to use your BluJax, press the control button for 3 seconds to turn it on. The blue light will blink 3 times when turning on.

3) Power Save Mode

If the paired Bluetooth device is out of range for 5 minutes, the BluJax will automatically go into sleep mode to preserve the battery power. When

rstreturningtothevehicle,simplypressthecontrolbuttononceontheBluJaxtowakeitup.

4) Battery Low

 Approximately8Hrs.ofplaybackfromtheBluJaxisexpectedonasinglecharge.WhentheBluJaxbatteryisgettinglow,itwillashred.

Please recharge BluJax soon.

Tech Support:

[email protected]

866-788-4237

WARNING:

This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage or

malfunction.

FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

1. Re-orientate or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that of which the receiver is connected.

4. Consult the dealer or an experienced radio / television technical for help.

Notice : The changes or modications not expressly approved by the party responsible compliance could void the user authority to operate the equipment.

BluJax

Bluetooth connection for streaming your music wirelessly. The Built-in button provides wireless control of the

paired Bluetooth device, providing the ability to play, pause, and skip tracks.

IN-CAR CONNECTIVITY

ISBT32