Supermicro PDSBA User manual

PDSBA-Q+

PDSBA+

PDSBA

PDSBE

USER’S MANUAL

Revision 1.1b

Manual Revision: Rev. 1.1b

Release Date: April 8, 2008

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software, if any,

and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or

reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,

SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE

USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.

SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED

WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,

INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B

digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

manufacturer’s instruction manual, may cause interference with radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, you are encouraged to try to correct the interference by one or more of

the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/television technician for help.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Preface

About This Manual

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use of

the

motherboard. The PDSBA-Q+/PDSBA+/PDSBA/PDSBE supports a

single Intel Quad-core/Dual-core Core2 Duo/E6000/E4000/Xeon 3000/Pentium

®

D/

Pentium

®

4/Celeron Processor with a system bus speed of 1066/800/533 MHz. The

Intel Core2 Duo, Xeon, Pentium

®

D, Pentium

®

4 and Celeron Processors, housed

in a Flip-Chip Land Grid Array, support the 775-Land Grid Array Package that inter-

faces with the motherboard via an LGA775 socket. The PDSBA-Q+/PDSBA+/PDS-

BA/PDSBE supports up to 4MB of L2 Cache, Intel Trusted Platform Module (TPM)

(Note), EM64T, Enhanced Intel SpeedStep (EIST), Intel Virtualization Technology

(VT), Streaming SIMD Extensions 2 (SSE2), Streaming SIMD Extensions 3 (SSE3),

and Execute Disable (XD) Bit. Please refer to the motherboard speciﬁ cations pages

on our website (http://www.supermicro.com/Product/motherboard) for updates on

processor support. This product is intended to be professionally installed.

Manual Organization

Chapter 1 describes the features, speciﬁ cations and performance of the mainboard

and provides detailed information about the chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when

installing the processor, memory modules and other hardware components into

the system. If you encounter any problems, see Chapter 3, which describes

troubleshooting procedures for the video, the memory and the system setup stored

in CMOS.

Chapter 4 includes an introduction to BIOS and provides detailed information on

running the CMOS Setup utility.

Appendix A lists BIOS POST Error Codes.

Appendix B and Appendix C list Windows OS and Software Installation Instruc-

tions.

Note: TPM support is available for the PDSBA-Q+/PDSBA+/PDSBA only.

Preface

iii

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

Conventions Used in the Manual:

Special attention should be given to the following symbols for proper installation and

to prevent damage done to the components or injury to yourself:

Danger/Caution: Instructions to be strictly followed to prevent catastrophic

system failure or to avoid bodily injury.

Warning: Important information given to ensure proper system installation

or to prevent damage to the components.

Note: Additional Information given to differentiate various models or to en

sure correct system setup.

iv

Preface

v

Notes

Table of Contents

Preface

About This Manual ........................................................................................... iii

Manual Organization ......................................................................................... iii

Conventions Used in the Manual ....................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist .......................................................................................................... 1-1

Contacting Supermicro .................................................................................... 1-2

PDSBA-Q+/PDSBA+/PDSBA/PDSBE Image ................................. 1-3

PDSBA-Q+/PDSBA+/PDSBA/PDSBE Layout .................................. 1-4

PDSBA-Q+/PDSBA+/PDSBA/PDSBE Quick Reference .................. 1-5

Motherboard Features .................................................................................. 1-6

Intel Q965/G965/P965 Chipsets: System Block Diagram .............................. 1-8

1-2 Chipset Overview ........................................................................................... 1-9

1-3 PC Health Monitoring ................................................................................... 1-10

1-4 Power Conﬁ guration Settings ....................................................................... 1-10

1-5 Power Supply ...................................................................................................1-11

1-6 Super I/O ........................................................................................................ 1-12

Chapter 2: Installation

2-1 Static-Sensitive Devices ................................................................................. 2-1

2-2 Motherboard Installation .................................................................................. 2-1

2-3 Processor and Heatsink Installation ............................................................... 2-2

2-4 Installing DDR2 Memory ................................................................................ 2-4

2-5 Control Panel Connectors/IO Ports ................................................................. 2-6

Back Panel Connectors/IO Ports .................................................................... 2-6

Front Control Panel ......................................................................................... 2-7

Front Control Panel Pin Deﬁ nitions ................................................................ 2-8

PWR LED ................................................................................................. 2-8

HDD LED ................................................................................................... 2-8

NIC1 LED Indicators ................................................................................ 2-9

OH/Fan Fail LED ....................................................................................... 2-9

Reset Button ............................................................................................ 2-10

PWR Button ............................................................................................. 2-10

2-6 Connecting Cables ....................................................................................... 2-11

ATX/Auxiliary Power Connectors ........................................................... 2-11

Universal Serial Bus (USB) ..................................................................... 2-12

vi

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

vii

Table of Contents

Chassis Intrusion .................................................................................... 2-12

Fan Headers ............................................................................................. 2-13

ATX PS/2 Keyboard and PS/2 Mouse Ports ............................................ 2-14

Serial Ports ............................................................................................... 2-14

Wake-On-Ring ......................................................................................... 2-15

Wake-On-LAN .......................................................................................... 2-15

GLAN1 Port .............................................................................................. 2-16

Speaker Connector .................................................................................. 2-16

High Deﬁ nition Audio (HDA) ..................................................................... 2-17

CD Header/Auxiliary Audio Header .......................................................... 2-17

2-7 Jumper Settings ............................................................................................ 2-18

Explanation of Jumpers ......................................................................... 2-18

GLAN Enable/Disable .............................................................................. 2-18

CMOS Clear ........................................................................................... 2-19

Watch Dog Enable ................................................................................... 2-19

CPU Front Side Speed ............................................................................ 2-20

PCI/PCI-Exp. Slots to SMB Speeds ......................................................... 2-20

USB Wake-Up .......................................................................................... 2-21

IDE Enable/Disable .................................................................................. 2-22

TPM Enable .............................................................................................. 2-22

Keyboard Wake-Up .................................................................................. 2-23

2-8 Onboard Indicators ....................................................................................... 2-24

GLAN LED Indicators ............................................................................... 2-24

Power LED ............................................................................................... 2-25

External RAID LED .................................................................................. 2-25

2-9 Parallel Port and Floppy Drive Connections ............................................... 2-26

Parallel Port Connector ............................................................................ 2-26

Floppy Connector .................................................................................... 2-27

IDE Connectors ........................................................................................ 2-28

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ....................................................................................... 3-1

No Power ................................................................................................... 3-1

No Video .................................................................................................. 3-2

Memory Errors ........................................................................................... 3-2

Losing the System’s Setup Conﬁ guration ................................................ 3-2

3-2 Technical Support Procedures ....................................................................... 3-2

3-3 Frequently Asked Questions .......................................................................... 3-3

3-4 Returning Merchandise for Service ................................................................. 3-4

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

viii

Chapter 4: BIOS

4-1 Introduction ....................................................................................................... 4-1

4-2 Running Setup ................................................................................................. 4-2

4-3 Main BIOS Setup ............................................................................................. 4-2

4-4 Advanced Setup ............................................................................................... 4-6

4-5 Security Setup ............................................................................................... 4-19

4-6 TPM State ....................................................................................................... 4-21

4-7 Physical Presence Operations ....................................................................... 4-22

4-8 Boot Settings .................................................................................................. 4-23

4-9 Exit .................................................................................................................. 4-24

Appendices:

Appendix A: BIOS POST Error Codes ......................................................................A-1

Appendix B: Installing the Windows OS ....................................................................B-1

Appendix C: Software Installation Instructions ...........................................................C-1

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.

If anything listed here is damaged or missing, contact your retailer.

All items are included in the Retail Box Only.

One (1) Supermicro Mainboard

Four (4) SATA cables (CBL-0044L)

Two (2) IDE hard drive cables (CBL-0036L-2) (PDSBA-Q+/PDSBA+ only)

One (1) USB cable (CBL-041)

One (1) ﬂ oppy drive ribbon cable (CBL-022L)

One (1) I/O shield (MCP-260-0001-00)

One (1) Supermicro CD containing drivers and utilities

One (1) User's/BIOS Manual

1-2

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

1-2 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer, B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Paciﬁ c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Website: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8228-1366, ext.132 or 139

Chapter 1: Introduction

1-3

PDSBA/PDSBE Image

PDSBA-Q+/PDSBA+ Image

Note: All pictures and drawings shown in this manual were based upon

the latest PCB Revision available at the time of publishing of the manual.

The motherboard you've received may or may not look exactly the same

as the ones shown in this manual.

1-4

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

Motherboard Layout

(not drawn to scale)

• See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front panel

connections.

• " " indicates the location of "Pin 1".

• The ITE Controller, IDE#1 and IDE#2 are available on the PDSBA-Q+/PDSBA+

only.

• Trusted Platform Module support and VGA are available on the PDSBA-Q+/

PDSBA+/PDSBA only.

• A special Consideration on Overclocking: Setting a high CPU FSB Speed, using

a high DRAM Frequency, or selecting a high CPU V-Core voltage, memory voltage,

chipset voltage, ICH chipset voltage, or FSB termination voltage may cause the

system to become unstable. If this occurs, reset the setting to the default setting.

Extra fans may be needed for proper system cooling.

S

UPER PDSBA+

®

Processor

JPWAKE

4-PinPWR

KB/MS

USB3/4/5/6

USB1/2

LAN

Fan3

Clock

Intel

PCI-E x1

PCI-E x16

PCI-E x4

PCI-33MHz

LAN

CTRL

JPL1

COM2

FWH

JL1

JWOR

I-SATA0

I-SATA1

FP

CTRL

F

an

2

JF1

Buzzer

24-Pin A

T

X

PWR

Super IO

Fan1/CPU Fan

Intel

J44

DIMM#1A (Blue)

DIMM#2A (Black)

DIMM#1B (Blue)

DIMM#2B (Black)

Floppy

Audio

WOL

JBT1

J27

J40

South Bridge

J12

J46

J11

J43

J28

J41

Battery

JPUSB1

JPUSB2

J31

COM1

JFSB1

J

F

SB

2

Slot7

Slot6

Slot5

Slot4

JI

2

C1

JI

2

C2

PCI-33MHz

Slot3

PCI-33MHz

Slot2

Slot1

PCI-33MHz

J13

J9

JS1

JS2

I-SATA4

JS5

JS6

I-SATA5

RAIDLED

USB7/8

J45

USB9/10

LE1

JLED

JWD

CD1

Parallel Port

J30

VGA

JG1

HDA

ITE

IDE#1

IDE#2

JP

2

JP3

North Bridge

Chapter 1: Introduction

1-5

Quick Reference

Jumpers Description Default Setting

JBT1 CMOS Clear (See Chapter 2)

JFSB1/JFSB2 CPU Frequency Pins 1-2/Pins 1-2(Auto)

JI

2

C1/JI

2

C2 SMB to PCI Slots Open/Open (Disabled)

JP2 (PDSBA-Q+/PDSBA+)ITE IDE Enabled Pins 1-2 (Enabled)

JP3 (PDSBA-Q+/PDSBA+/PDSBA) TPM Enable Pins 1-2 (Enabled)

JPL1 Giga-bit LAN Enable Pins 1-2 (Enabled)

JPUSB1 B/P USB Wake Up Pins 2-3 (Disabled)

JPUSB2 F/P USB Wake Up Pins 2-3 (Disabled)

JPWAKE1 Keyboard/Mouse Wake-Up Pins 1-2 (Enabled)

JWD Watch Dog Timer Out Option Pins 1-2 (Reset)

Connectors Description

Audio Audio Port

CD-In (CD1) Audio CD Input Header

Chassis Intrusion Chassis Intrusion Header

COM1, COM2 COM Port/Serial Port 1 & Port 2 Connectors

DIMM#1A,#2A,#1B,#2B Memory (DIMM) Slots (1 through 4)

Fans 1-3 Fan1: CPU Fan, Fan2/3: Chassis Fan Headers

Floppy Floppy Disk Connector

FP Audio Front Panel Audio Connector (See Chapter 2)

LAN Port Ethernet RJ45 (Gigabit LAN) Connector

IDE#1/IDE#2 IDE Hard Drive #1 & Hard Drive #2 (See Page 1-4)

J40 ATX 24-Pin Power Connector

J41 12V 4-pin Power Connector (required)

JF1 Front Control Panel Header

SATA #0/1/4/5 SATA (#0/1/4/5) Headers

KB/Mouse PS/2 Keyboard/Mouse

LE1 Standby Warning LED Indicator

PWR LED Power LED Indicator

Printer Parallel Printer Port

RAID LED External RAID LED Header (Optional for OEM Only)

Slot 1-Slot 4 PCI 33 MHz (PCI #1-#4) (Note)

Slots 5-7 PCI-E x4 (Slot5), PCI-E x16 (Slot6), PCI-Ex1 (Slot7)

Speaker Speaker Header

USB 1/2 (Back Panel) Universal Serial Ports 1-2

USB 3/4/5/6 (Back Panel) Universal Serial Ports 3-6

USB 7/8/9/10 (Front Panel) USB ports 7/8 (J44), USB 9/10 (J45)

VGA Video/Graphic Connector (See Notes on Page 1-4)

WOL Wake-On-LAN Header

WOR Wake-On-Ring Header

Note: PCI Slot 4 (PCI-33 MHz) is not available on the PDSBA/PDSBE only.

1-6

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

Motherboard Features

CPU

Single Intel Quad-core/Dual-core Core2 Duo/E6000/E4000/Xeon 3000/Pentium

®

D/Pentium

®

4/Celeron Processor with a system bus speed of 1066/800/533

MHz

Supports Intel EM64T, Enhanced Intel SpeedStep (EIST), Intel Virtualization

Technology (VT)

, Streaming SIMD Extensions 2 & 3 (SSE2 & SSE3) and Ex-

ecute Disable (XD) Bit.

Memory

Supports unbuffered single or dual channel ECC/Non ECC Unbuffered DDR2

up to 8GB/s (DDR2 800/667/533) for single channel mode or dual-channel

Interleaved mode.

Chipsets

• Intel Q965-Express GMCH (North Bridge) and ICH8 (South Bridge) (PDSBA-

Q+)

• Intel G965 GMCH (North Bridge) and ICH8 (South Bridge) (PDSBA/PDSBA+)

• Intel P965 MCH (North Bridge) and ICH8 (South Bridge) (PDSBE)

Expansion Slots

• One (1) PCI-Express x16 (Slot 6)

• One (1) PCI-Express x4 (Slot 5)

• One (1) PCI-Express x1 (Slot 7)

• Four (4) 32-bit PCI 33MHz (Slot 1 to Slot 4) (PCI Sot 4 are available on the

PDSBA/PDSBE only.)

BIOS

• 8 Mb Firmware Hub Phoenix Flash BIOS

• DMI 2.3, PCI 2.2, ACPI 1.0/2.0, Hardware BIOS virus protection, SMBIOS 2.3,

Plug and Play (PnP)

PC Health Monitoring

• Onboard voltage monitors for +1.8V, CPU core, +3.3V, +3.3V standby, +5V,

Vbat (battery voltage) and ±12V

• Fan status monitor with ﬁ rmware 4 pin fan speed control

• CPU 3-Phase-switching voltage regulator

• SuperDoctor III, Watch Dog, NMI

• Power-up mode control for recovery from AC power loss

• CPU/System overheat LED and control

• System resource alert via Supero Doctor III

• Auto-switching voltage regulator for the CPU core

• CPU Thermal Trip support

•

Chapter 1: Introduction

1-7

• Thermal Monitor 2 (TM2) support

• SMT support (PDSBA-Q+/PDSBA+/PDSBA only)

ACPI Features

• Slow blinking LED for suspend state indicator

• BIOS support for USB keyboard

• Main switch override mechanism

• External modem ring-on

Onboard I/O

• Built in ICH8 SATA Controller, 4 connectors for 4 devices (300MB/S)

• 1 ﬂ oppy port interface (up to 2.88 MB)

• 1 Fast UART 16550 compatible serial port/header

• Intel 82573L Gigabit Ethernet Controller (PCI-E)

• 1 EPP (Enhanced Parallel Port) and ECP (Extended Capabilities Port) with

parallel port supported

• PS/2 mouse and PS/2 keyboard ports

• ITE Controller supports four IDE hard drives (PDSBA-Q+/PDSBA+ only)

• Up to 10 USB (Universal Serial Bus) 2.0 ports for a speed of up to 480Mbps

• Realtek ALC 883 7.1 Channel High Deﬁ nition Audio (HDA) codecs supports 10

DAC Channels

• Built-in GMCH and Onboard VGA Connector (PDSBA-Q+/PDSBA+/PDSBA

only)

Other

• Trusted Platform Module (TPM) support (PDSBA-Q+/PDSBA+/PDSBA only)

• Wake-on-LAN

• Wake-on-Ring (WOR)

• System Bus Clock Frequency Selection (Overclocking) Support (Note)

• Suspend-to-RAM

• Onboard +3V Standby Power Warning LED ("LE1")

• Pb Free

CD Utilities

• BIOS ﬂ ash upgrade utility

• Drivers and software for Intel Q965-Express/G965/P965 chipset utilities

Dimensions

• ATX form factor, 11.6" x 9.6" (294.6 x 243.8 mm)

Note: For SATA RAID conﬁ guration instructions, please refer to the Intel

HostRAID Utility User Guide listed on our website (http://www.supermicro.

com/Product/motherboard).

1-8

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your motherboard. See the following pages for the

actual speciﬁ cations of each motherboard.

SLOTS

LGA775_PROCESSOR

ICH-8

FWH

LPC I/O

MS.KB.

FDD. SER.1/2 PRN.

VRM 11.0

ADDR

CTRL

DATA

LPC

PCI_32

DDR2_800/667/533

VRM V11.0

DMI

3_PCI_x32

DIMM_CHA

SATA/300

4x SATAII

CK505 CLK

1 P

CIE_x16

GRAPHIC

GMCH (Q965/G965).

DIMM_CHB

PORTS

PCIE_x16

INTEGRATED

GRAPHI

C

82573 LA

N

SLO

TS

1_PCIE_x1

PCIE_x4

W83627HG

7.1-CH

HD_AUDIO

FSB: 1066/800/533MHz

LPC

USB2.0/1.1

HD-A

PCIE_x1

1_PCIE_x8

SLOTS

MCH (P

965)

(Q965/G965)

TPM

PORTS

10x USB2.0

LPC

1_PCI_x32

OR

ITE8212

POR

TS

2x IDE133

Note: Integrated Graphics is NOT available for the P965 Chipset.

Chapter 1: Introduction

1-9

1-2 Chipset Overview

The Intel Q965-Express/G965/P965 Chipsets are specially designed for use with

Quad-core or Dual-core 1066/800/533 MHz processors. These chipsets consist of

two primary components: the Graphic Memory Controller Hub (GMCH)/Memory

Controller Hub (MCH) and the I/O Controller Hub (ICH8). Optimized for the Quad-

core/Dual-core Core2 Duo/E6000/E4000/Xeon 3000/Pentium

®

D/Pentium

®

4/Cel-

eron Processor via an LGA775 socket, the Q965-Express/G965/P965 provides the

performance and feature-set required for high-end UP quad-core and Dual-core pro-

cessor desktop solutions. (Note: GMCH is for the Q965-Express and G965 only.)

Graphic Memory Controller Hub (GMCH)/Memory

Controller Hub (MCH)

The GMCH/MCH manages the data ﬂ ow of the following interfaces: the CPU inter-

face (FSB), the System Memory interface (DRAM Controller) and the I/O Control-

ler through DMI (Direct Media) Interface. The MCH supports a FSB frequency of

1066/800/533 MHz using a scalable CPU. The Q965-Express/G965/P965 platforms

support the eighth generation I/O Controller Hub (Intel ICH8) to provide a variety

of I/O related functions.

Intel ICH8 System Features

The Intel ICH8 offers the data buffering and interface arbitration required for the

system to obtain peak performance. The Intel ICH8 supports up to six PCI-Express

root ports, up to four SATA ports at generation 1 and 2 speeds and up to ten USB

2.0 ports. In addition, the Intel ICH8 features High Deﬁ nition Audio controller which

supports extreme multimedia applications and various third party codecs.

1-10

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

1-3 PC Health Monitoring

This section describes the PC health monitoring features of the PDSBA-Q+/PDS-

BA+/PDSBA/PDSBE. The motherboard has an onboard System Hardware Monitor

chip that supports PC health monitoring.

Recovery from AC Power Loss

BIOS provides a setting for you to determine how the system will respond when

AC power is lost and then restored to the system. You can choose for the system

to remain powered off (in which case you must hit the power switch to turn it back

on) or for it to automatically return to a power on state. See the Power Lost Con-

trol setting in the BIOS chapter of this manual to change this setting. The default

setting is Always OFF.

Onboard Voltage Monitoring

The onboard voltage monitor will scan the following voltages continuously for the

CPU Core, +1.8V, +3.3V, +3.3V standby, +5V, Vbat and ±12V. Once a voltage

becomes unstable, it will give a warning or send an error message to the screen.

Users can adjust the voltage thresholds to deﬁ ne the sensitivity of the voltage

monitor by using SD III.

Fan Status Monitor with Software

The PC health monitor can check the RPM status of the cooling fans via Supero

Doctor III.

CPU Overheat LED and Control

This feature is available when the user enables the CPU overheat warning function

in the BIOS. This allows the user to deﬁ ne an overheat temperature. When this

temperature reaches the pre-deﬁ ned threshold, the CPU thermal trip feature will be

activated and it will send a signal to the Speaker LED and, at the same time, the

CPU speed will be decreased.

1-4 Power Conﬁ guration Settings

This section describes features of your motherboard that deal with power and

power settings.

Chapter 1: Introduction

1-11

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start blinking

to indicate that the CPU is in suspend mode. When the user presses any key, the

CPU will wake-up and the LED will automatically stop blinking and remain on.

BIOS Support for USB Keyboard

If the USB keyboard is the only keyboard in the system, it will function like a normal

keyboard during system bootup.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a system

suspend button. When the user presses the power button, the system will enter a

SoftOff state. The monitor will be suspended, and the hard drive will spin down.

Pressing the power button again to wake-up the whole system. During the SoftOff

state, the ATX power supply provides power to keep the required circuitry in the

system alive. In case the system malfunctions and you want to turn off the power,

just press and hold the power button for 4 seconds. The power will turn off and no

power will be provided to the motherboard.

Wake-On-Ring (WOR) Header

Wake-up events can be triggered by a device such as the external modem ringing

when the system is in the SoftOff state. Note that external modem ring-on can only

be used with an ATX 2.01 (or above) compliant power supply.

1-5 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates of 1 GHz and faster.

The

PDSBA-Q+/PDSBA+/PDSBA/PDSBE accommodates 12V ATX

power supplies. It is strongly recommended that you use a high quality power sup-

ply that meets 12V ATX power supply Speciﬁ cation 1.1 or above. It is also required

that the 12V 4-pin power connection (J41) be used for high-load conﬁ gurations. In

areas where noisy power transmission is present, you may choose to install a line

ﬁ lter to shield the computer from noise. It is recommended that you also install a

power surge protector to help avoid problems caused by power surges.

1-12

PDSBA-Q+/PDSBA+/PDSBA/PDSBE User’s Manual

1-6 Super I/O

The disk drive adapter functions of the Super I/O chip include a ﬂ oppy disk drive

controller that is compatible with industry standard 82077/765, a data separator,

write pre-compensation circuitry, decode logic, data rate selection, a clock genera-

tor, drive interface control logic and interrupt and DMA logic. The wide range of

functions integrated onto the Super I/O greatly reduces the number of components

required for interfacing with ﬂ oppy disk drives. The Super I/O supports two 360 K,

720 K, 1.2 M, 1.44 M or 2.88 M disk drives and data transfer rates of 250 Kb/s,

500 Kb/s or 1 Mb/s.

It also provides two high-speed, 16550 compatible serial communication ports

(UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable baud

rate generator, complete modem control capability and a processor interrupt sys-

tem. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps as well

as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support

higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Conﬁ guration

and Power Interface), which includes support of legacy and ACPI power manage-

ment through a SMI or SCI function pin. It also features auto power management

to reduce power consumption.

Page is loading ...

Supermicro PDSBA User manual

Supermicro PDSBA User manual

Related papers

Other documents