Work-pro DMX AIR MKII User manual

Type
User manual

Work-pro DMX AIR MKII

Work-pro DMX AIR MKII is a wireless DMX transceiver system that allows you to control your DMX-compatible lighting fixtures without the need for cables. This can be a major convenience, especially for setups where running cables would be difficult or impossible.

The DMX AIR MKII system consists of two units: a transmitter and a receiver. The transmitter is connected to your DMX controller, and the receiver is connected to your lighting fixtures. The two units communicate wirelessly, sending DMX data from the controller to the fixtures.

The DMX AIR MKII system operates in the 2.4GHz frequency band and has a range of up to 300 feet. It supports up to 13 DMX channels, which is enough for most basic lighting setups.

Work-pro DMX AIR MKII

Work-pro DMX AIR MKII is a wireless DMX transceiver system that allows you to control your DMX-compatible lighting fixtures without the need for cables. This can be a major convenience, especially for setups where running cables would be difficult or impossible.

The DMX AIR MKII system consists of two units: a transmitter and a receiver. The transmitter is connected to your DMX controller, and the receiver is connected to your lighting fixtures. The two units communicate wirelessly, sending DMX data from the controller to the fixtures.

The DMX AIR MKII system operates in the 2.4GHz frequency band and has a range of up to 300 feet. It supports up to 13 DMX channels, which is enough for most basic lighting setups.

1. Connect a DMX Controller to the DMX input on the device used as transmitter
2. Connect your Fixture to the device used as receiver
3. Please turn on DMX controller and the luminaire, then start the wireless controller (Transmitter)
The receiver must be in off state.
4.When the register LED of Transmitter are in slowly strobe status, please press the register
button making the register LED strobe quickly,
- Now, start the Receiver immediately, at this time, the register LED of Receiver will enter the
quickly strobe status.
- Then they will match with each other. After 18 seconds, the register LED of Transmitter and
Receiver will strobe slowly,
- At the same time they connect successfully and control the luminaire by the controller.
5. When you need Transmitter connect much more Receivers, you only press the button on the
Transmitter, the register LED of Transmitter enter strobe quickly status,
- Then connect and turn on the Receiver (R1, R2, R3, etc). Please make again step 2.
Suitable for Indoor use: IP 20 RF transmitter power 18 dBm
Voltage Input AC 100-240V, 50 Hz RF receive sensitivity -90 dBm
Consumption 2W max. Antenna SMA.50 5%
Frequency Band 2400 to 2483 MHz Dimensions 250 x 250 x 350 mm
Channels 13 channels Weight 360 g
RF channel data rate 250 Kbps
SPECIFICATIONS
DMX AIR MK II (Emitter/Transmitter)
1. SAFETY INSTRUCTIONS
- CAUTION! Be careful with your operations. with a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!
- This device has left our premises in absolutely perfect condition. In order to maintain this condition
and to ensure a safe operation, it is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
- Important: damages caused by the disregard of this user manual are not subject to warranty.
- Keep away from heaters and other heating sorces!
- If the device has been exposed to drastic temperaure fluctuation (e.g. after transportation), do
not switch it on immediately. The arising condensation water might damage your device.
- Leave the device switched off until it has reached room temperature.
- If the external flexible cable or cord of this luminary is damaged, it shall be exclusively replaced
by the manufacturer or his service agent or a similar qualified person in order to avoid hazard.
- Always disconnect from the mains, when the device is not in user or before cleaning it.
- Keep away children and amateurs from the device.
- There are no serviciable parts inside the device. Maintenance and service operations are only to
be carried out by authorized dealers.
2. OPERATIONS
1
User Manual/Manual de Uso DMX AIR MK II
EN
  • Page 1 1
  • Page 2 2

Work-pro DMX AIR MKII User manual

Type
User manual

Work-pro DMX AIR MKII

Work-pro DMX AIR MKII is a wireless DMX transceiver system that allows you to control your DMX-compatible lighting fixtures without the need for cables. This can be a major convenience, especially for setups where running cables would be difficult or impossible.

The DMX AIR MKII system consists of two units: a transmitter and a receiver. The transmitter is connected to your DMX controller, and the receiver is connected to your lighting fixtures. The two units communicate wirelessly, sending DMX data from the controller to the fixtures.

The DMX AIR MKII system operates in the 2.4GHz frequency band and has a range of up to 300 feet. It supports up to 13 DMX channels, which is enough for most basic lighting setups.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages