Bushnell 98037 User manual

Type
User manual

This manual is also suitable for

OPERATION MANUAL
EQUIPMENT
Hysol 175-
SPRAY
P
/
N 98037
®
P/N 98041
Loctite is a trademark of Loctite Corporation, U.S.A. Data in the manual i
s subject to change without notice.
Copyright 2001. Loctite Corporation. All rights reserved. 985119 06/01
Loctite Brazil
Av. Prof. Vernon Krieble, 91
06690-11-Itapevi
São Paulo-Brazil
Loctite America
s
1001 Trout Brook Crossing
Rocky Hill, CT 06067-3910
Loctite Canada Inc.
2225 Meadowpine Boulevard
Mississauga, Ontario L5N 7P2
Loctite Company de México, S.A.d e C.V.
Calzada de la Viga s/n, Fracc. Los Laureles
Loc. Tulpetlac, C.P. 55090
Ecatepac de Morelos, Edo. de México,
México
www.loctite.com
A Company
Hysol 175-
SPRAY
-HT
®
Page 1
Contents
1. Please Observe the Following................................................................................... 2
1.1. Safety .......................................................................................................................... 2
1.2. Items supplied.............................................................................................................. 2
2. Description................................................................................................................. 2
3. Technical Data............................................................................................................ 3
4. Installation.................................................................................................................. 3
5. Operation.................................................................................................................... 4
5.1. Applying Adhesive - Spray Adjustment ......................................................................... 4
5.2. Adhesive Flow Rate Adjustment ................................................................................... 4
6. Application Hints........................................................................................................ 5
7. Troubleshooting......................................................................................................... 5
8. Care and Maintenance ............................................................................................... 6
9. Accessories and Spare Parts .................................................................................... 6
10. Warranty.....................................................................................................................8
11. Appendix. ................................................................................................................... 9
12. Exploded Diagram.................................................................................................... 10
13. Parts List. ................................................................................................................. 11
Page 2
1. Please Observe the Following
1.1.Safety
Do not touch the nozzle or molten adhesive with bare skin as they are hot - the
operating temperature of the Loctite
®
Hysol
®
175-SPRAY and 175-SPRAY-HT
applicators is approximately 400ºF (200ºC). Protective gloves should always be
worn. Careless handling can cause skin burns. If molten adhesive comes into
contact with the skin immerse the affected area immediately in plenty of cold water.
Seek medical advice if necessary.
In addition to the safety instructions herein, any statutory regulations, local fire
insurance regulations, or other generally valid “regulations for accident prevention”
must be complied with when using this tool.
Never use the tool if it is damaged in any way.
Do not use this tool in damp rooms, outdoors while it is raining, or where there is
high humidity.
Do not use this tool in the vicinity of any heat-sensitive materials, or any flammable
materials, liquids, or gases.
Only use extension cables that meet the specification shown in “Technical data”.
Never pull on the tool’s connecting cable.
1.2. Items supplied
Loctite
®
Hysol
®
175-SPRAY
Pneumatically-driven Hot Melt Cartridge Spray Dispenser, fitted with 356°F (180°C)
thermostat (suitable for standard spray hotmelt adhesives)
Valve body airline adaptor
Plastic Stand
Manual
Loctite
®
Hysol
®
175-SPRAY-HT
Pneumatically-driven Hot Melt Cartridge Spray Dispenser, fitted with 383°F (195°C)
thermostat (suitable for polyamide spray hotmelt adhesives)
Valve body airline adaptor
Plastic Stand
Manual
2. Description
The Loctite
®
Hysol
®
175-SPRAY and 175-SPRAY-HT are the highest output, hand-
held industrial spray hotmelt applicators available. With its two powerful 250W
stainless steel cartridge heaters, they are capable of dispensing up to 9 lbs. of molten
hotmelt per hour, yet only take 10 minutes to warm up from cold.
Supported by a range of spray adhesive formulations, the Loctite
®
Hysol
®
175-SPRAY
and 175-SPRAY-HT are suitable for most applications - they can even be used with
heat sensitive substrates such as expanded polystyrene and other plastic foams.
Also, the Loctite
®
Hysol
®
175-SPRAY and 175-SPRAY-HT system are solvent-free and
non-toxic, so there are none of the environmental problems often associated with other
spray adhesive applicators.
Designed to comply with world wide safety standards, the Loctite
®
Hysol
®
175-SPRAY
and 175-SPRAY-HT also feature a totally enclosed heater housing, and are fitted with
thermal fuse protection.
Page 3
3. Technical Data
Dimensions (L x H x W): approx. 11 13/16” x 9 15/32” x 2 17/32”
(Approx. 300 x 240 x 65 mm)
Total weight: approx. 3 lbs. (1.4 Kg)
Connection cable with mains plug: 10 ft (3 m) long
Operating voltage: 110-120 VAC 50/60Hz
Power consumption 500W
Heating up time: 10 minutes
Operating temperature: 175-SPRAY approx. 356°F (180°C)
175-SPRAY-HT approx. 383°F (195°C)
Diameter of adhesive inlet: 1 11/16” (43 mm)
Extension cable: max. 65ft (20 m) long
Wire cross section: at least 16 a.w.g. (1.5 mm
2
)
Air Supply / Pneumatic Minimum - 45 p.s.i. (3 bar)
Maximum - 100 p.s.i. (7 bar)
Approximate Spray Pattern Minimum Maximum
Ultra Wide Spray Pattern / 985216 1 ½[38mm] 6” [150mm]
Wide Spray Nozzle Assembly / 985122 1 ¼” [32mm] 5” [127mm]
Narrow Spray Pattern Assembly / 985211 ½ [13mm] 1 ¼”[32mm]
4. Installation
Before using the tool for the first time check it carefully for signs of external damage. If
any transit damage is found DO NOT USE THE TOOL - return it to your supplier
immediately.
Steps 1 – 5 should be followed before connection to the mains supply:
1. Insert the applicator stand into the grooves at the base of the handle. Stand
applicator on a flat surface.
2. Connect the air supply hose to a clean, dry and regulated air supply using the
Quick-Disconnect fitting provided (use of a filter/regulator is recommended)
3. Pull piston back fully and rotate upwards.
4. Load two adhesive cartridges into the barrel of the tool and push fully forward.
5. Rotate the piston down and slide forward fully until it contacts the rear of the
adhesive cartridge - it should engage about 5/16" (6-8mm) into the applicator
barrel.
6. Connect tool to mains supply.
7. Red ‘Power On’ indicator light illuminates.
2
3
5
1
4
USERS AIR SUPPLY
Page 4
8. Allow the applicator to thoroughly warm up for 10 minutes. Do not attempt to
operate the applicator until this time has elapsed.
5. Operation
Normal use:
Fit the stand and place the applicator in an upright position on a flat surface.
Plug the applicator into the power supply socket, and switch on the power. Wait 10
minutes for the applicator to reach its normal operating temperature.
Squeeze the trigger to advance the piston and extrude molten adhesive through the
nozzle.
To stop extruding adhesive simply release the trigger.
During use, the piston will advance into the barrel as the trigger is pulled. A point will
be reached where the piston no longer advances, and the sound of air escaping can
be heard - this indicates that the applicator needs reloading.
Release the trigger.
Pull the piston back.
Insert a new adhesive cartridge.
Operate the tool normally.
5.1. Applying Adhesive - Spray Adjustment
Turn the spray air adjustment control completely clockwise. Holding the applicator
facing away from you, squeezing the trigger will extrude a bead of adhesive from the
nozzle. While continuing to squeeze the trigger, rotate the spray air adjustment control
slowly counter-clockwise; this changes the adhesive bead into an ever-finer spiral
spray pattern. Continue to adjust the control until a suitable spray pattern is obtained
to suit your application. To stop the adhesive flow simply release the trigger.
5.2. Adhesive Flow Rate Adjustment
The flow rate of adhesive is dependent on the air pressure to the piston, and this is
adjusted by varying the setting of the pressure regulator on the air supply to the
applicator.
The air pressure operating range for the applicator is:
Minimum 45 p.s.i. (3 bar)
Maximum 100 p.s.i. (7 bar)
.
USERS AIR SUPPLY
Page 5
6. Application Hints
As with all adhesives, performance depends on conditions of use. Suggestions or
recommendations contained herein are for guidance only, since actual conditions of
use are outside the supplier’s control.
Ensure that the surfaces to be bonded are dry, free from dust, grease, and
loose particles.
Apply adhesive to one surface only. Bring the two surfaces together as
quickly as possible; the faster the bond is made, the greater the strength.
A heavier spray pattern increases both working time and bond strength.
When gluing dissimilar materials, apply the adhesive to the least heat
conductive of the two.
On materials that are cold to the touch, a better bond can be made by pre-
warming them before applying adhesive.
Surplus adhesive can be trimmed using a sharp knife once it has cooled.
Should molten adhesive drip onto a smooth or polished surface, allow it to cool
completely before removal.
Spray adhesives can be applied directly to expanded polystyrene and other
plastic foams.
Use only genuine Loctite
®
Hysol
®
adhesives to ensure reliable performance.
Loctite
®
Hysol
®
adhesives are non-toxic and non-flammable.
7. Troubleshooting
Before proceeding with any repair or maintenance operation disconnect the tool
from the mains electricity supply.
Glue “Backup” and “Meltdown”
“Backup” occurs when hot molten adhesive in the glue chamber is forced back
between the barrel wall and the outside surface of the adhesive cartridge and piston.
Once this adhesive cools, it may lock the adhesive cartridge in the barrel, preventing,
or at least restricting, normal extrusion. By far the most likely cause of backup is
allowing insufficient warm-up time before operating the tool (the molten glue in the glue
chamber cannot escape forwards because the nozzle is blocked, due to being
insufficiently warm). In the vast majority of cases the backup self-clears once the tool,
having fully reached operating temperature, is operated again. For the rare occasions
where the backup does not self-clear, turn the spray air adjuster fully clockwise; this
will switch off the spray air, allowing the full pneumatic line pressure to be applied to
the piston (the tool will operate as a bead tool).
"Meltdown" occurs when the rear of the adhesive cartridge softens to the extent that it
is not rigid enough to drive the cartridge forward without collapsing. As with backup,
the molten adhesive can solidify, potentially locking the cartridge and / or piston into
the barrel. Meltdown is caused by leaving the tool switched on for extended periods of
time without operating it. It is recommended that, if the tool is to be left standing for
forty minutes or more, it should be switched off and only switched back on when
preparing to use it again.
The Loctite
®
Hysol
®
175-SPRAY and 175-SPRAY-HT tools are fitted with specially
coated pistons which have non-stick characteristics far superior to any PTFE coating;
this minimises the effect of any backup or meltdown, should it occur.
Page 6
FOR ANY REPAIRS OR ADJUSTMENTS – OTHER THAN THOSE DETAILED IN
THIS MANUAL – PLEASE CONTACT 1-800-LOCTITE.
8. Care and Maintenance
Every attempt has been made to make this exceptionally powerful tool both reliable
and trouble-free. However the following precautions should be noted:
Make sure that the applicator is up to temperature before attempting to operate.
Do not leave the applicator switched on for long periods without use. If the
applicator is not to be used for forty minutes or more, switch it off and restart when
required.
Keep the applicator upright when not in use, never lay it on its side. Always use the
stand provided, or the optional bench stand or suspension unit (see Spares and
Accessory lists at the end of this manual).
Do not use excessive force on the trigger. Ensure that the tool has fully warmed up
before use.
Keep the nozzle clean to prevent adhesive build-up. This is easily done by wiping
the nozzle with clean paper or cloth while the nozzle is still warm.
9. Accessories and Spare Parts
Spare Parts Part Number
Complete Nozzle Assembly – Wide Angle 2mm 985122
(fitted as standard)
Applicator Stand 985069
Barrel PTFE 985071
Barrel Support Assembly 985091
Piston Support Assembly 985093
Piston 985095
Thermostat Assembly, 180°C 985123
Thermostat Assembly, 195°C (for polyamides) 985079
Heater Assembly 120 Volts 985080
PCB Assembly 985083
Thermal Fuse, Spacer Assembly 985076
Valve Body Airline Adapter 985240
Heater Housing Kit For 98037 (EVA Adhesive) 985232
Qty 1 – O-ring Heater Housing, item 5
Qty 1 – Heater Housing, item 6
Qty 1 – Fitting, item 30
Qty 1 – Ground Screw, item 38
Qty 1 - Lock Washer, item 42
Heater Housing Kit For 98041 (Polyamides Adhesives) 985239
Qty 1 – O-ring Heater Housing, item 46
Qty 1 – Heater Housing, item 47
Qty 1 – Fitting, item 30
Qty 1 – Ground Screw, item 38
Qty 1 - Lock Washer, item 42
Handle Kit 985228
Qty 2 – Moulded handles, item 1
Qty 6 – Casing Screws, item 37
Piston Support Hardware Kit 985229
Qty 1 – Washer, special with 4 holes, item 33
Page 7
Qty 1 – Pivot o-ring, item 28
Qty 1 - Washer, flat nylon, item 43
Qty 6 – Casing screws, item 37
Page 8
Trigger Valve Kit 985233
Qty 1 – Urethane Hose, item 19
Qty 1 – Urethane Hose, item 20
Qty 1 - Trigger Valve Assembly, item 14
Qty 1 – Philips Pan Head Screw, item 16
Piston Support O-ring Kit, Qty 5 985234
Nozzle Shroud Kit, Qty 5 985235
Spray Air System Assembly Kit 985236
Qty 1 - Spray Air System Assembly, item 22
Qty 1 – Urethane Hose, item 20
Qty 1 – Urethane Hose, item 19
Qty 1 – PTFE Hose, item 21
U.S. Cord Set Assembly 985231
Qty 1 – Cordset, item 17
Qty 1 – Clamp, item 18
Qty 2 – Screws, item 41
Accessories Part Number
Complete Nozzle Assembly
Ultra Wide Spray Pattern, 2mm Orifice 985216
Wide Spray Nozzle Assembly 985122
Narrow Spray Pattern Assembly 985211
(For spray pattern definition see Section 3 – Technical Data)
Heavy-Duty Free-Standing Metal Stand 985087
Tool Hanger/Balancer 985243
10. Warranty
This applicator is guaranteed against faulty workmanship, materials and malfunction
for a period of 12 months from the date of purchase. This guarantee does not apply:
1. If the applicator has been dropped, damaged due to careless handling or has not
been used in accordance with the manufacturer’s instructions.
2. If the applicator has been modified in any way.
3. If the applicator has been opened or the electrical cable has been damaged or
replaced.
4. If adhesive other than formulations supplied by the manufacturer of the applicator
have been used.
The manufacturer undertakes to repair or replace at their discretion. The tool will be
returned to the distributor or user freight paid.
Seller and Manufacturer’s only obligation shall be to replace such quantity of the
product proved to be defective. Neither seller nor manufacturer shall be liable for any
injury, loss or damage direct or consequential, arising out of the use, or the inability to
use, the product. User shall determine the suitability of the product for his intended
use and the user assumes all risks and liability whatsoever in connection therewith.
Page 9
985087
HEAVY DUTY FREE-STANDING
METAL STAND
985243
TOOL HANGER / BALANCER
11. Appendix.
Pictures of available nozzles/accessories.
985211
NARROW SPRAY
NOZZLE ASSEMBLY
985122
WIDE SPRAY
NOZZLE ASSEMBLY
985216
ULTRA WIDE SPRAY
NOZZLE ASSEMBLY
Page 10
12. Exploded Diagram.
Page 11
13. Parts List.
48 1 THERMOSTAT ASSEMBLY, 195°C, 383°F 985079
47 1 HEATER HOUSING ASSEMBLY HEATER HOUSING KIT 985239
46 1 HEATER HOUSING O-RING HEATER HOUSING KIT 985239
45 1 HELICAL SPRING LOCK WASHER, 1/4", BLACK OXIDE
44 2 WASHER, 1/4", FLAT, BRIGHT ZINC PLATE
43 1 WASHER, FLAT, NYLON PISTON SUPPORT HARDWARE KIT 985229
42 2 HELICAL SPRING LOCK WASHER HEATER HOUSING KIT 985232
41 2 PHILLIPS PAN HEAD SCREW, SELF TAPPING, #6-20 X 3/8, BRIGHT ZINC US CORDSET ASSEMBLY KIT 985231
40 3 PHILLIPS ROUND HEAD SCREW, #6-32 x 1/4 LONG
39 4 PHILLIPS ROUND HEAD SCREW, #10-32 x 5/8 LONG, BLACK OXIDE
38 1 EARTH (GROUND) SCREW, 4BA x 1/2" LONG HEATER HOUSING KIT 985232
37 6 CASING SCREW, 12mm LONG SELF-TAPPER AVAILABLE IN MULTIPLE KITS 985288 or 985229
36 1 PHILLIPS PAN HEAD SCREW, SELF TAPPING, #6-20 X 3/4, BRIGHT ZINC TRIGGER VALVE KIT 985233
35 1 PHILLIPS PAN HEAD SCREW, 1/4-20 x 1/2 LONG, BLACK OXIDE
34 1 SOCKET HEAD SHOULDER SCREW, 1/4" x 1"
33 1 WASHER, SPECIAL WITH 4 HOLES PISTON SUPPORT HARDWARE KIT 985229
32 1 BARREL SUPPORT EARTH WIRE ASSEMBLY
31 1 HEATER HOUSING EARTH WIRE ASSEMBLY
30 1 FITTING, BARBED HEATER HOUSING KIT 985232
29 1 RED LENS
28 1 PIVOT O-RING
27 1 PISTON 985095
26 1 PISTON SUPPORT O-RING 985234
25 1 PISTON SUPPORT ASSEMBLY 985093
24 1 PISTON PLATE
23 1 BARREL SUPPORT 985091
22 1 SPRAY AIR SYSTEM ASSEMBLY SPRAY AIR SYSTEM KIT 985236
21 1 PTFE TUBING, 195mm LONG
20 1 URETHANE TUBING, 50mm LONG AVAILABLE IN MULTIPLE KITS 985236 or 985233
19 1 URETHANE TUBING, 75mm LONG
18 1 CORDSET CLAMP US CORDSET ASSEMBLY KIT 985231
17 1 U.S. CORDSET ASSEMBLY, 3M US CORDSET ASSEMBLY KIT 985231
16 1 AIRLINE ASSEMBLY, 3M
15 1 CONNECTOR & LIGHT PCB ASSEMBLY, 120 VOLT 985083
14 1 TRIGGER VALVE ASSEMBLY TRIGGER VALVE KIT 985233
13 1 TRIGGER
12 1 DISPENSER STAND 985069
11 2 HEATER ASSEMBLY, 120 VOLT, 250 WATT 985078
10 1 THERMOSTAT ASSEMBLY, 180°C, 356°F 985123
9 1 WIDE SPRAY NOZZLE ASSEMBLY, 2mm 985122
8 1 NOZZLE SHROUD NOZZLE SHROUD KIT 985235
7 1 THERMAL FUSE & SPACER ASSEMBLY 985076
6 1 HEATER HOUSING ASSEMBLY HEATER HOUSING KIT 985232
5 1 HEATER HOUSING 0-RING HEATER HOUSING KIT 985232
4 1 LOCK RING, ALUMINIUM
3 2 BARREL SUPPORT RING
2 1 BARREL, PTFE 985071
1 1 HANDLES, PAIR HANDLE KIT 985224
ITEM QTY. DESCRIPTION REBUILD KITS AVAILABLE PART NO.
PARTS LIST
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Bushnell 98037 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI