Pelco Home Security System C1666M-A (4/06) User manual

Brand: Pelco

Model: Home Security System C1666M-A (4/06)

Category: Supplementary music equipment

Type: User manual

This manual is also suitable for

INSTALLATION

TW3001AR

Active Receiver

Single Channel for UTP Transmission

C1666M-A (4/06)

C1666M-A (4/06) 3

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,

such as vases shall be placed on the apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or

moisture.

16. Installation should be done only by qualified personnel and conform to all local codes.

17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is

designed for indoor use only and it must not be installed where exposed to rain and moisture.

18. Use only installation methods and materials capable of supporting four times the maximum

specified load.

19. A CCC-approved power cord must be used to power this equipment when used in China.

4 C1666M-A (4/06)

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Changes and Modifications not expressly approved by the manufacturer or registrant of this

equipment can void your authority to operate this equipment under Federal Communications

Commission’s rules.

In order to maintain compliance with FCC regulations shielded cables must be used with this

equipment. Operation with non-approved equipment or unshielded cables is likely to result in

interference to radio and television reception.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

The materials used in the manufacture of this document and its components are compliant to the

requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to

comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical

and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this

equipment.

C1666M-A (4/06) 5

Description

The TW3001AR is a single-channel active receiver that can receive live video over unshielded twisted

pair (UTP) cable.

The adaptive technology in the TW3001AR automatically adjusts the low, medium and high frequency

components of the video signal allowing for the best possible video transmission. The adaptive

technology eliminates the need for manual adjustment by automatically adjusting to provide the most

favorable video transmission depending on cable length needed. The unit has been optimized for use

with Cat5e and Cat6 cable, although Cat3 and Cat5 cable can be used for shorter distances.

The DIP switch on the bottom of the TW3001AR allows you to override the adaptive technology and

manually select the cable distance. Switches 1, 2, 3, and 4 can be set to 4,000 feet (1,219 meters),

3,000 feet (914 meters), 2,000 feet (610 meters), and 1,000 feet (305 meters), respectively. Switch 5

can be set to high mode and low mode.

There are two ways to power the TW3001AR. You can power it by installing it into an RK5000PS-3U

using the 4-pin connector. For stand-alone power, you can use the 2-pin power connector and use

either a 12 VDC power supply (supplied) or a 24 VAC power supply.

The following features are found on the TW3001AR:

• Full motion color/black-white video up to 4,000 feet (1,219 meters) with Cat5e or Cat6

• Supports Coaxitron

control (PTZ control signals) up to 750 feet (229 meters)

• Compatible with all Pelco twisted pair equipped cameras, enclosures, and domes

• Built-in surge suppression

• Easy termination with removable UTP connector

• Supports NTSC, PAL, and SECAM

• Can be mounted into a Pelco fiber rack, wall mount base kit, or wall clip

6 C1666M-A (4/06)

PARTS OF THE RECEIVER

Figure 1. TW3001AR Parts

 Rubber Feet (4): For placing unit on a flat surface, such as a desk or shelf.

 Status LED: Lights red when there is no UTP video being received. Lights green when there is

UTP video being received. Flashes amber when Coaxitron pan/tilt/zoom (PTZ) control commands

are being received.

 Pelco Badge: Lights blue to indicate power when using either the 4-pin rack power connector

or the 2-pin power connector.

 Rack Power Connector: 4-pin, power from RK5000PS-3U.

 Power Connector (3.5 mm): 2-pin; stand-alone power, 12 VDC or 24 VAC.

 UTP Connector (2.5 mm): 2-pin connector with removable mating connector.

 BNC Connector: Coaxial output.

 DIP Switch: Override the adaptive technology with the manual selection of cable distance

(1,000 to 4,000 feet or 305 to 1,219 meters). Switch 5 is used for selecting high mode or low

mode.















MODEL

FREQ

THIS DEVICE

COMPLIES

WITH

PART 15 OF THE

FCC RULES.

OPERATION

IS SUBJECT

TO THE

FOLLOWING T

CONDITIONS:

(1)

THIS DEVICE MA

Y NOT CAUSE

HARMFUL

INTERFERENCE,

AND

(2) THIS DEVICE

MUST

ANY

INTERFERENCE

RECEIVED,

INCLUSING

INTERFERENCE

THA

AY CAUSE UNDESIRED

OPERA

TION.



C1666M-A (4/06) 7

Installation

Make sure all parts are present for the unit.

1 Universal power supply (Part #PS04-1502-0512G)

1 Wall clip

1 2-pin power connector

1 2-pin UTP connector

MOUNTING

The TW3001AR receiver is 3 rack units high and can be mounted into a fiber rack, onto a wall using

a fiber wall mount kit or into the supplied wall clip.

USING A RACK

You can mount a TW3001AR into either an RK5000PS-3U (for power) or an RK5000-3U. For additional

mounting information, refer to the RK5000PS-3U/RK5000-3U Fiber Rack Mount Chassis Installation

manual.

USING WALL MOUNT KITS

The optional WM5001-3U wall mount base kit allows attachment of a single TW3001AR to a wall. Up

to two WM5001-3UEXP wall mount expansion kits can be used to allow attachment of two additional

receivers to the wall. For additional information, refer to the Fiber Wall Mount Kits Installation man-

ual.

8 C1666M-A (4/06)

USING A WALL CLIP

To attach the TW3001AR receiver to a wall using the supplied wall clip, refer to Figure 2 and do the

following:

1. Attach the wall clip to a wall using two screws (not supplied).

2. Slide the receiver into the clip until the two holes on the bottom of the receiver align with the

two holes on the lower flange of the clip.

3. Attach the receiver to the clip using the two Phillips pan head screws provided with the clip.

Figure 2. Mounting the TW3001AR Using the Wall Clip

WALL CLIP

TW3001AR

SCREW, PHILLIPS

PAN HEAD WITH

LOCK WASHER (2)

LOWER

FLANGE

HORIZONTAL

MOUNTING HOLE (2)

VERTICAL

MOUNTING HOLE (2)

UPPER

FLANGE

C1666M-A (4/06) 9

SETTING THE DIP SWITCHES

You can override the adaptive technology by manually adjusting switches 1 through 4 on the DIP

Switch. The factory default switch positions are shown in Figure 3. Switches 1 through 4 are set to

AUTO and Switch 5 is set to H MODE (high mode).

Figure 3. Default Switch Positions

If you want to transmit video over 4,000 feet (1,219 meters) of UTP cable, set switch 1 to 4K. Set

switch 2 to 3K if you want a distance of 3,000 feet (914 meters), switch 3 to 2K if you want a distance

of 2,000 feet (610 meters), and switch 4 to 1K if you want a distance of 1,000 feet (305 meters).

You can set only one distance at a time.

With switch 5 you can select H (high) or L (low). High mode is the default position and is used when

video is 1Vp-p. Low mode is used when video is less than 1Vp-p.

10 C1666M-A (4/06)

APPLICATIONS

You can connect the TW3001AR active receiver to transmitters, such as the TW3001P passive trans-

ceiver and the TW3001AT active transmitter, and to Pelco UTP cameras, such as the CC3710/CC3610

Series. Although you can connect these products using an unshielded twisted pair Cat3 and Cat5

cable, Cat5e and Cat6 are recommended for the best video performance.

Always connect the UTP wires on the Cat cable from + to + and from - to -. For example, if you connect

the blue wire to the + on the TW3001AR make sure you connect the other end of the blue wire to the

+ on the transmitter.

Table A shows the maximum cable distance with Coaxitron or video only when connecting the

TW3001AR to a TW3001P passive transceiver with a particular type of Cat cable.

NOTE: Cat5e cable is recommended for the best video performance.

Table B shows the minimum size for a single wire and stranded wire.

Table A. Cable Distance with TW3001P

Cable Type

Maximum Distance

(with Coaxitron)

Maximum Distance

(video only)

Cat3e 750 ft (229 m) 1,500 ft (457 m)

Cat5e 750 ft (229 m) 3,000 ft (914 m)

Cat5e 750 ft (229 m) 4,000 ft (1,219 m)

Cat6e 750 ft (229 m) 4,000 ft (1,219 m)

Table B. Wire Gauge

Wire Gauge (minimum size)

Single Wire (solid)

24 AWG (0.25 mm

)

Stranded Wire (flexible)

24 AWG (1.0 mm

)

C1666M-A (4/06) 11

Figure 4 shows a TW3001AR connected to a UTP Camclosure

Figure 4. TW3001AR Connected to a UTP Camclosure

CAMCLOSURE

TW3001AR

UTP

MONITOR

12 VDC OR 24 VAC

POWER SUPPLY

BLUE WIRE =

GRAY WIRE =

POWER FROM RK5000PS-3U

12 C1666M-A (4/06)

Figure 5 shows a TW3001AR connected to a UTP fixed camera.

Figure 5. TW3001AR Connected to a UTP Fixed Camera

TW3001AR

FIXED CAMERA

8 PINS (4-/5+)

MONITOR

UTP

PIN 5 +

PIN 4 -

10 PINS

(5-/6+)

12 VDC OR 24 VAC

POWER SUPPLY

POWER FROM RK5000PS-3U

C1666M-A (4/06) 13

Figure 6 shows a TW3001AR connected to a UTP Spectra

Dome for Coaxitron PTZ control.

Figure 6. TW3001AR Connected to a Spectra Dome

TW3001AR

UTP

VIDEO

COAXITRON

SPECTRA

MONITOR

MATRIX

VC-UTP BOARD

12 VDC OR 24 VAC

POWER SUPPLY

POWER FROM RK5000PS-3U

14 C1666M-A (4/06)

Figure 7 shows a TW3001AR connected to a TW3001P passive transceiver. The TW3001P then

connects to a non-UTP fixed camera.

Figure 7. TW3001AR Connected to a Single Passive Transceiver

TW3001AR

TW3001P

UTP

MONITOR

DIRECT

CONNECTION

FIXED

CAMERA

12 VDC OR 24 VAC

POWER SUPPLY

POWER FROM RK5000PS-3U

C1666M-A (4/06) 15

Figure 8 shows a TW3001AR connected to a TW3032P passive transceiver.

Figure 8. TW3001AR Connected to a 32-Channel Passive Transceiver

TW3001AR

TW3032P

MONITOR

UTP

12 VDC OR 24 VAC

POWER SUPPLY

POWER FROM RK5000PS-3U

16 C1666M-A (4/06)

Figure 9 shows a TW3001AR connected to a TW3004P passive transceiver. The TW3004P then

connects to a non-UTP fixed camera.

Figure 9. TW3001AR Connected to a 4-Channel Passive Transceiver

TW3001AR

TW3004P

UTP

MONITOR

FIXED

CAMERA

12 VDC OR

24 VAC

POWER SUPPLY

POWER FROM RK5000PS-3U

C1666M-A (4/06) 17

Specifications

ELECTRICAL

Input Voltage 12 VDC or 24 VAC, 50-60Hz

Power Consumption 2.5 W

Wire Type Unshielded twisted pair (24 AWG maximum)

Wire Category Cat3 or better

DC Loop Resistance 52 ohms per 1,000 feet

Differential Capacitance 19pF/ft max

Transient Immunity 300 W peak pulse power (8/20 US)

VIDEO CHARACTERISTICS

Video Output 1, BNC

Format NTSC, PAL, SECAM

Frequency Response DC to MHz

Common Mode/Differential

Mode Rejection >70 dB

MECHANICAL

Connectors

BNC Video output

4-Pin Connector Rack power

2-Pin Connector (2.5 mm) UTP input/output

2-Pin Connector (3.5 mm) Power

Construction Steel

Finish Silver

GENERAL

Operating Temperature 32° to 167°F (0° to 75°C)

Relative Humidity 0 to 90%, noncondensing

Data Transmission Supports Coaxitron up to 750 feet

LED Indicators Pelco badge (blue); status LED (red, green, flashing amber)

Dimensions 8.75" D x 1.08" W x 4.81" H

(22.23 x 2.74 x 12.22 cm)

Unit Weight 1.0 lb (0.45 kg)

18 C1666M-A (4/06)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of

shipment.

Exceptions to this warranty are as noted below:

• Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products.

• Three years on Spectra

IV products.

• Three years on Genex

Series products (multiplexers, server, and keyboard).

• Three years on Camclosure

and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models, which have a five-year warranty.

• Three years on PMCL200/300/400 Series LCD monitors.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

• Two years on Spectra III

™

, Esprit

, ExSite

™

, and PS20 scanners, including when used in continuous motion applications.

• Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).

• Two years (except lamp and color wheel) on Digital Light Processing (DLP

) displays. The lamp and color wheel will be covered for a period of

90 days. The air filter is not covered under warranty.

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura

™

Series distributed network-based video

products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight

prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this

warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products

shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state

to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and

provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written

explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization

number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate

address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the

following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA