ELECTROLUX-REX RWF108315W User manual

Brand: ELECTROLUX-REX

Model: RWF108315W

Category: Washing machines

Type: User manual

RWF 108315 W

................................................ .............................................

EN WASHING MACHINE USER MANUAL

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

CONTENTS

Safety information 2

Safety instructions 3

Product description 4

Special accessories for installation 6

Control panel 6

Personalization 8

First use 9

Daily use 9

Helpful hints and tips 13

Washing programmes 14

Consumption values 16

Care and cleaning 17

What to do if… 20

Technical data 23

Installation 23

Electrical connection 25

Environment concerns 26

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read

the supplied instructions. The manufacturer is not responsible

if an incorrect installation and use causes injuries and dam-

ages. Always keep the instructions with the appliance for fu-

ture reference.

Children and vulnerable people safety

Warning! Risk of suffocation, injury or permanent disability.

• Do not let persons, children included, with reduced physical

sensory, reduced mental functions or lack of experience and

knowledge use the appliance. They must have supervision

or instruction for the operation of the appliance by a person

who is responsible for their safety.

• Do not let children play with the appliance.

• Keep all packaging away from children.

• Keep all detergents away from children.

• Keep children and pets away from the appliance door when

it is open.

• If the appliance has a child safety device, we recommend

you activate it.

General Safety

• Before maintenance, deactivate the appliance and discon-

nect the mains plug from the mains socket.

• Do not change the specification of this appliance.

2 electrolux

• Obey the maximum load volume of 8 kg (refer to the “Pro-

gramme chart” chapter).

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard.

• The operating water pressure (minimum and maximum)

must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)

• The ventilation openings in the base (if applicable) must not

be obstructed by a carpet.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging and the transit

bolts.

• Keep the transit bolts. When you move

the appliance again you must block the

drum.

• Do not install or use a damaged appli-

ance.

•Do not install or use the appliance where

the temperature is less than 0 °C or

where it is exposed to the weather.

• Obey the installation instruction supplied

with the appliance.

• Make sure that the floor where you install

the appliance is flat, stable, heat resistant

and clean.

• Do not install the appliance where the ap-

pliance door can not be fully opened.

• Always be careful when you move the

appliance because it is heavy. Always

wear safety gloves.

• Make sure that there is air circulation be-

tween the appliance and the floor.

• Adjust the feet to have the necessary

space between the appliance and the

carpet.

Electrical connection

Warning! Risk of fire and electrical

shock.

• The appliance must be earthed.

• Make sure that the electrical information

on the rating plate agrees with the power

supply. If not, contact an electrician.

• Always use a correctly installed shock-

proof socket.

• Do not use multi-plug adapters and ex-

tension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable. Con-

tact the Service or an electrician to

change a damaged mains cable.

• Connect the mains plug to the mains

socket only at the end of the installation.

Make sure that there is access to the

mains plug after the installation.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains

plug.

• Do not touch the mains cable or the

mains plug with wet hands.

• This appliance complies with the E.E.C.

Directives.

Water connection

• Make sure not to cause damage to the

water hoses.

• The appliance is to be connected to the

water mains using the new supplied

hose-sets. Old hose sets must not be

reused.

• Before you connect the appliance to new

pipes or pipes not used for a long time,

let the water flow until it is clean.

electrolux 3

• The first time you use the appliance,

make sure that there is no leakage.

Use

Warning! Risk of injury, electrical

shock, fire, burns or damage to the

appliance.

• Use this appliance in a household envi-

ronment.

• Obey the safety instructions on the deter-

gent packaging.

• Do not put flammable products or items

that are wet with flammable products in,

near or on the appliance.

• Do not touch the glass of the door while

a programme operates. The glass can be

hot.

• Make sure that you remove all metal ob-

jects from the laundry.

• Do not put a container to collect possible

water leakage under the appliance. Con-

tact the Service to ensure which acces-

sories can be used.

Care and Cleaning

Warning! Risk of injury or damage to

the appliance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

Disposal

Warning! Risk of injury or suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent chil-

dren and pets to get closed in the appli-

ance.

Service

• Contact the Service to repair the appli-

ance. We recommend only the use of

original spare parts.

PRODUCT DESCRIPTION

Your new appliance meets all modern requirements for effective treatment of laundry

with low water, energy and detergent consumption. Its new washing system allows

total use of detergent and reduces water consumption so saving energy.

Detergent dispenser drawer

Control panel

Door opening handle

Rating Plate

4 electrolux

Drain pump

Adjustable feet

Detergent dispenser drawer

Compartment for detergent used for

prewash and soak phase or for stain re-

mover used during the stain action phase (if

available). The prewash and soak detergent

is added at the beginning of the wash pro-

gramme. The stain remover is added dur-

ing the stain action phase.

Compartment for powder or liquid de-

tergent used for main wash. If using liquid

detergent pour it just before starting the

programme.

Compartment for liquid additives (fabric

softener, starch).

Follow the product manufacturer’s recom-

mendations on quantities to use and do not

exceed the «MAX» mark in the detergent

dispenser drawer. Any fabric softener or

starching additives must be poured into the

compartment before starting the wash pro-

gramme.

Flap for powder or liquid detergent (see "Flap for powder or liquid detergent" in

the chapter "Daily use" for more details).

Bleach

Alternatively the softener, it is also possible to use a bleach agent in the compartment

with the programmes for white cottons.

Proceed as follows:

•

Put the bleach in the compartment

. Do not exceed the «MAX» mark in the deter-

gent dispenser drawer.

• Run a programme for white cottons.

• At the end of the programme, run the programme RINSE. Use softener, if desired. This

helps to eliminate any bleach residues.

Important! Never pour bleach and softener into the compartment at the same time.

Child safety device

Make sure that children or pets do not

climb into the drum. To prevent children

and pets becoming trapped inside the

drum the machine incorporates a special

feature. To activate this device, rotate the

button (without pressing it) inside the door

clockwise until the groove is horizontal. If

necessary use a coin.

To disable this device and restore the pos-

sibility of closing the door, rotate the button

counterclockwise until the groove is vertical.

electrolux 5

SPECIAL ACCESSORIES FOR INSTALLATION

Rubber feet kit (4055126249)

Available from your authorized dealer.

The rubber feet are particularly recommen-

ded on floating, slippery and wooden floors.

Mount the rubber feet to prevent vibration,

noises and displacement of the appliance

during operation.

Read carefully the instructions supplied with

the kit.

Fixing plate kit (4055171146)

Available from your authorized dealer.

If you install the appliance on a plinth, se-

cure the appliance in the fixing plates.

Follow the instructions supplied with the kit.

CONTROL PANEL

Henceforth the programme selector dial, the buttons and the display will be indicated

with the numbers given in this table.

1 2 3 4 5 6 7 8

Programme selector dial

SPIN REDUCTION button (Centrifuga)

OPTIONS button (Opzioni)

–PREWASH (Prelavaggio)

–DAILY (Quotidiano)

–SUPER QUICK (Rapido)

EXTRA RINSE button (Extra Risciac-

quo)

Display

START/PAUSE button (Avvio/Pausa)

DELAY START button (Delay)

Indicator pilot lights

Table of Symbols

Programme dial

= Cold wash

= Delicates

Buttons Lights

= Rinse Hold = Washing

Combinations of buttons = Door locked

= Child safety lock = End of cycle

6 electrolux

Programme Selector Dial

It allows you to switch the appliance on/off

and/or to select a programme.

Spin speed Reduction

By pressing this button you can reduce the

maximum spin speed allowed for the selec-

ted programme or to select the available

option(s).

Rinse hold

By selecting this function the water of the

last rinse is not emptied out to prevent the

fabrics from creasing. Before opening the

door it will be necessary to empty out the

water. To empty out the water, please read

the paragraph «At the end of the pro-

gramme».

Prewash

By selecting this option the machine per-

forms a prewash cycle before the main

wash phase. The washing time will be pro-

longed. This option is recommended for

heavily soiled laundry.

Daily

A cycle to be used for daily soiled cotton,

synthetic or delicate items in order to obtain

good washing performance in a short time.

Super Quick

Short cycle for lightly soiled items or for

laundry which needs only freshening up.

We recommend you to reduce the fabrics

Extra Rinse

This appliance is designed to save energy.

If it necessary to rinse the laundry using an

extra quantity of water (extra rinse), select

this option. Some additional rinses will be

performed. This option is recommended for

people who are allergic to detergents, and

in areas where the water is very soft.

Start Pause

This button allows you to start or to inter-

rupt the selected programme.

Delay Start

The programme can be delayed from 30

min - 60 min - 90 min, 2 hours and then by

1 hour up to a maximum of 20 hours by

means of this button.

Indicator pilot lights

8.1

8.2

8.3

After having pressed the button 6, the

WASHING pilot light (8.1) illuminates. When

the pilot light 8.1 illuminates this means that

the machine is operating.

The DOOR pilot light (8.2) illuminates when

the programme starts and indicates if the

door can be opened:

• light on: the door cannot be opened. The

machine is working or has stopped with

water left in the tub.

• light off: the door can be opened. The

programme is finished or the water has

been emptied out.

• light flashing: the door is opening in a few

minutes.

When the programme has finished the END

CYCLE pilot light (8.3) comes on.

electrolux 7

Display

5.1:

•

Duration of selected programme

After selecting a programme, the duration

is displayed in hours and minutes (for ex-

ample

). The duration is calculated

automatically on the basis of the maxi-

mum recommended load for each type of

fabric. After the programme has started,

the time remaining is updated every mi-

nute.

•

Alarm codes

In the event of operating problems, some

alarm codes can be displayed, for exam-

ple

(see chapter «What to do if...»).

• End of programme

When the programme has finished three

blinking zeros (

) are displayed, the

Door pilot light (8.2), the Washing pilot

light (8.1) and the pilot light of button 6

go out and the door can be opened.

•

Incorrect option selection

If an option which is not compatible with

the set wash programme is selected, the

message Err is displayed for a few sec-

onds and the red pilot light of button 6

light starts blinking.

• Delay Start

The selected delay set by means of the

relevant button appears on the display for

a few seconds. The delay time value de-

creases by one unit every hour. When

only 1 hour remains, the time decreases

every minute.

5.2:

•

Heating Phase

During the washing cycle the display

shows a temperature icon (5.2) to indi-

cate that the appliance has started the

heating phase of the water in the tub.

5.3:

• Child safety lock

This device permits you to leave the ap-

pliance unsupervised without having the

worry that children might be injured by or

cause damage to the appliance. This

function remains able also when the

washing machine is not working.

There are two different ways to set this

option:

– before pressing button 6: it will be im-

possible to start the machine;

– after having pressed the button 6: it will

be impossible to change any other

programme or option.

To enable (disable) this option press si-

multaneously for about 6 seconds 3 and

4 buttons until the symbol 5.3 appears

(disappears) on the display.

PERSONALIZATION

Acoustic signals

The machine is provided of an acoustic de-

vice, which sounds in the following cases:

• at the end of the cycle

• in the event of operating problems.

By pressing the 2 and 3 buttons simultane-

ously for about 6 seconds, the acoustic

signal is deactivated (except for the events

of operating problems). By pressing these 2

buttons again, the acoustic signal is reacti-

vated.

8 electrolux

FIRST USE

• Ensure that the electrical and water

connections comply with the installa-

tion instructions.

• Remove the polystyrene block and

any material from the drum.

• Pour 2 litres of water into the main

wash compartment

of the deter-

gent drawer in order to activate the

ECO valve. Then run a cotton cycle

at the highest temperature without

any laundry in the machine, to re-

move any manufacturing residue

from the drum and tub. Pour 1/2 a

measure of detergent into the main

wash compartment and start the

machine.

DAILY USE

Load the laundry

Open the door by carefully pulling the door

handle outwards. Place the laundry in the

drum, one item at a time, shaking them out

as much as possible. Close the door.

Make sure that no laundry stays between

the seal and the door. There is a risk of wa-

ter leakage or damage to the laundry.

Measure out the detergent and the fab-

ric softener

Pull out the dispenser drawer until it stops.

Measure out the amount of detergent re-

quired, pour it into the main wash compart-

ment

or in the appropriate compartment

if the selected programme/option it requires

(see more details in «Detergent dispenser

drawer»).

If required, pour fabric softener into the

compartment marked

(the amount used

must not exceed the «MAX» mark in the

drawer). Close the drawer gently.

Flap for powder or liquid detergent

UP- The flap position if using POWDER

detergent

DOWN - The flap position if using LIQ-

UID detergent during main wash

electrolux 9

If the flap is not in the desired position:

• Pull out the dispenser drawer until it

stops.

The flap is down and you wish to use

powder detergent:

• Turn the flap up.

• Measure out the detergent.

• Pour the powder detergent into the main

wash compartment

• Remove the remaining powder form

the flap.

• There is remaining powder detergent

in the main wash compartment at

the end of a washing programme.

Check if the flap is in the right posi-

tion.

The flap is up and you wish to use liq-

uid detergent:

• Turn the flap down.

• Measure out the detergent.

For the quantity of detergent, refer al-

ways to what is written on the product

packing and ensure that the detergent

can be poured in the drawer.

• Pour the liquid detergent in the compart-

ment

without exceeding the limit indi-

cated in the flap.

10 electrolux

• Close the dispenser drawer.

Warning! Do not use the flap in

"DOWN" position with:

• Gelatinous detergent or thick deter-

gent.

• Powder detergent.

• With programmes with prewash.

• Do not use liquid detergent if the

washing programme doesn't start

immediately.

In these cases, use the flap in "UP"

position .

Select the required programme by

turning the programme selector dial (1)

You can choose the right programme for

any type of laundry following the descrip-

tions on the washing programme tables

(see «Washing Programmes»). Turn the

programme selector dial to the required

programme. The programme selector de-

termines the type of washing cycle (e.g.

water level, drum movement, number of rin-

ses) and the washing temperature accord-

ing to the type of laundry. The pilot light of

button 6 starts blinking and the display

shows the duration of the selected pro-

gramme. The selector dial can be turned ei-

ther clockwise or counterclockwise. Posi-

tion

to Reset programme/Switching OFF

the machine.

For the description of each washing

programmes of the selector dial, con-

sult the chapter «Washing pro-

grammes».

At the end of the programme the selec-

tor dial must be turned to position

to switch the machine off.

Caution! If you turn the programme

selector dial to another programme

when the machine is working, the red

pilot light of button 6 will blink 3 times

and the message Err is displayed on

the display to indicate a wrong

selection. The machine will not perform

the new selected programme.

Reduce the spin speed by pressing

button 2

When the required programme has been

selected, your appliance automatically pro-

poses the maximum spin speed provided

for that programme.

Press button 2 repeatedly to change the

spin speed, if you want your laundry to be

spun at a speed different from the one pro-

posed by the washing machine. The rele-

vant light will light up.

Select the available options by

pressing buttons 2, 3 and 4

Depending on the programme, different

functions can be combined. These must be

selected after choosing the desired pro-

gramme and before starting the pro-

gramme. When these buttons are pressed,

the corresponding pilot lights illuminate.

When they are pressed again, the pilot

lights go out. If an incorrect option is selec-

ted, the integrated red pilot light of the but-

ton 6 flashes for 3 times.

For the compatibility among the wash-

ing programmes and the options see

chapter «Washing Programmes».

Select the Delay Start by pressing

button 7

Before you start the programme, if you wish

to delay the start, press the button 7 re-

peatedly, to set the desired delay. The set

delay time value (up to 20 hours) will appear

on the display a few seconds, then the du-

ration of the programme will appear again.

You must select this option after you have

set the programme and before you press

button 6.

electrolux 11

You can cancel or modify the delay time at

any moment, before you press button 6.

Selecting the delayed start:

1. Set the programme and the required

options.

2. Press button 7 to set the delay start .

3. Press button 6:

– the machine starts its hourly count-

down.

– The programme will start after the

selected delay has expired.

Cancelling the delayed start after having

pressed button 6:

1. Press button 6 to set the washing ma-

chine to PAUSE.

Press button 7 once until the value

’

is displayed

3. Press button 6 again to start the pro-

gramme.

Important! The selected delay can be

changed only after selecting the washing

programme again.

The Delay Start can not be selected with

the DRAIN programme.

Start the programme by pressing

button 6

To start the selected programme, press the

button 6, the corresponding green pilot light

stops blinking. The pilot lights 8.1 and 8.2

illuminate to indicate that the appliance

starts operating and the door is locked.

To interrupt a programme which is running,

press the button 6: the corresponding

green pilot light starts blinking.

To restart the programme from the point at

which it was interrupted, press the button 6

again. If you have chosen a delayed start,

the machine will begin the countdown.

If an incorrect option is selected, the red pi-

lot light of the button 6 blinks for 3 times

the message Err is displayed for a few sec-

onds.

Altering an option or a running

programme

It is possible to change some options be-

fore the programme carries them out.

Before you make any change, you must

PAUSE the appliance by pressing the but-

ton 6.

Changing a running programme is possible

only by resetting it. Turn the programme se-

lector dial to

and then to the new pro-

gramme position. Start the new programme

by pressing the button 6 again. The wash-

ing water in the tub will be not emptied out.

Interrupting a programme

Press the button 6 to interrupt a pro-

gramme which is running, the correspond-

ing green pilot light starts blinking.

Press the button again to restart the pro-

gramme.

Cancelling a programme

Turn the selector dial to

to cancel a pro-

gramme which is running.

You can select now a new programme.

Opening the door

After the programme has started (or during

the delay time) the door is locked. If you

need to open the door, press first the but-

ton 6 to set the machine to PAUSE. After a

few minutes the light 8.2 goes out. It is pos-

sible to open the door.

If this light remains lit and the door is

locked, this means that the machine is al-

ready heating or that the water level is too

high. In any case, do not try to force the

door!

If you cannot open the door but you need

to open it you have to switch the machine

off by turning the selector dial to

. After a

few minutes the door can be opened (pay

attention to the water level and temper-

ature!).

After closing the door, it is necessary to set

the programme and options again. Press

button 6 to start the machine.

At the end of the programme

The machine stops automatically. The dis-

play shows three blinking zeros (

Some acoustic signals sound. The light of

button 6, the lights 8.1 and 8.2 go off.

After some minutes the light 8.3 illuminates.

The door can be opened.

If you have set a programme or an option

that ends with water left in the tub, the light

8.2 remains on. The door is locked. The

water must be emptied out before opening

the door. During this time the drum contin-

ues to rotate at regular intervals.

Follow the below instructions to empty out

the water:

Turn the programme selector dial to

12 electrolux

2. Set the draining or spinning pro-

gramme.

3. If needed reduce the spin speed.

4. Press button 6.

At the end of the programme, the light 8.2

goes off. The door can be now opened.

Turn the programme selector dial to

switch the machine off.

Remove the laundry from the drum and

carefully check that the drum is empty. If

you do not intend to carry out another

wash, close the water tap. Leave the door

open to prevent the formation of mildew

and unpleasant smells.

Stand by : once the programme has finish-

ed after a few minutes the energy saving

system will be enabled. The brightness of

the display is reduced. By pressing any but-

ton the appliance will come out of the ener-

gy saving status.

HELPFUL HINTS AND TIPS

Sorting out the laundry

Follow the wash code symbols on each

garment label and the manufacturer’s

washing instructions. Sort the laundry as

follows: whites, coloureds, synthetics, deli-

cates, woollens.

Before loading the laundry

Never wash whites and coloureds together.

Whites may lose their «whiteness» in the

wash.

New coloured items may run in the first

wash; they should therefore be washed

separately the first time.

Button up pillowcases, close zip fasteners,

hooks and poppers. Tie any belts or long

tapes.

Remove persistent stains before washing.

Rub particularly soiled areas with a special

detergent or detergent paste.

Treat curtains with special care. Remove

hooks or tie them up in a bag or net.

Removing stains

Stubborn stains may not be removed by

just water and detergent. It is therefore ad-

visable to treat them prior to washing.

Blood: treat fresh stains with cold water.

For dried stains, soak overnight in water

with a special detergent then rub in the

soap and water.

Oil based paint: moisten with benzine

stain remover, lay the garment on a soft

cloth and dab the stain; treat several times.

Dried grease stains: moisten with turpen-

tine, lay the garment on a soft surface and

dab the stain with the fingertips and a cot-

ton cloth.

Rust: oxalic acid dissolved in hot water or a

rust removing product used cold. Be careful

with rust stains which are not recent since

the cellulose structure will already have

been damaged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well

(whites and fast coloureds only).

Grass: soap lightly and treat with bleach

(whites and fast coloureds only).

Ball point pen and glue: moisten with

acetone

, lay the garment on a soft cloth

and dab the stain.

Lipstick: moisten with acetone as above,

then treat stains with methylated spirits.

Treat any residual marks with bleach.

Red wine: soak in water and detergent,

rinse and treat with acetic or citric acid,

then rinse. Treat any residual marks with

bleach.

Ink: depending on the type of ink, moisten

the fabric first with acetone

, then with

acetic acid; treat any residual marks on

white fabrics with bleach and then rinse

thoroughly.

Tar stains: first treat with stain remover,

methylated spirits or benzine, then rub with

detergent paste.

Detergents and additives

Good washing results also depend on the

choice of detergent and use of the correct

quantities to avoid waste and protect the

environment.

1) do not use acetone on artificial silk

electrolux 13

Although biodegradable, detergents contain

substances which, in large quantities, can

upset the delicate balance of nature.

The choice of detergent will depend on the

type of fabric (delicates, woollens, cottons,

etc.), the colour, washing temperature and

degree of soiling.

All commonly available washing machine

detergents may be used in this appliance:

• powder detergents for all types of fabric

• powder detergents for delicate fabrics

(60°C max) and woollens

• liquid detergents, preferably for low tem-

perature wash programmes (60°C max)

for all types of fabric, or special for wool-

lens only.

The detergent and any additives must be

placed in the appropriate compartments of

the dispenser drawer before starting the

wash programme.

If using liquid detergents, a programme

without prewash must be selected.

Your appliance incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Follow the product manufacturer’s recom-

mendations on quantities to use and do

not exceed the «MAX» mark in the de-

tergent dispenser drawer.

Quantity of detergent to be used

The type and quantity of detergent will de-

pend on the type of fabric, load size, de-

gree of soiling and hardness of the water

used.

Follow the product manufacturers’ instruc-

tions on quantities to use.

Use less detergent if:

• you are washing a small load

• the laundry is lightly soiled

• large amounts of foam form during wash-

ing.

Degrees of water hardness

Water hardness is classified in so-called

“degrees” of hardness. Information on hard-

ness of the water in your area can be ob-

tained from the relevant water supply com-

pany, or from your local authority. If the wa-

ter hardness degree is medium or high we

suggest you to add a water softener follow-

ing always the manufacturer’s instructions.

When the degree of hardness is soft, read-

just the quantity of the detergent.

WASHING PROGRAMMES

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

Cotoni

95° - 60°

Main wash - Rinses

Maximum spin speed

Max. load 8 kg - Reduced load 4 kg

For white cottons (heavily soiled items).

SPIN REDUCTION

RINSE HOLD

PREWASH

DAILY / SUPER

QUICK

EXTRA RINSE

Eco

60°

Main wash - Rinses

Maximum spin speed

Max. load 8 kg

For white and fast coloured cotton

This programme can be selected for slightly or normally

soiled cotton items. The temperature will decrease and the

washing time will be extended. This allows to obtain a

good washing efficiency so saving energy.

SPIN REDUCTION

RINSE HOLD

PREWASH

EXTRA RINSE

14 electrolux

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

Eco

40°

Main wash - Rinses

Maximum spin speed

Max. load 8 kg

For coloured cotton

This programme can be selected for slightly or normally

soiled cotton items. The temperature will decrease and the

washing time will be extended. This allows to obtain a

good washing efficiency so saving energy.

SPIN REDUCTION

RINSE HOLD

PREWASH

EXTRA RINSE

Cotoni

40° - Cold

Main wash - Rinses

Maximum spin speed

Max. load 8 kg - Reduced load 4 kg

For coloured cottons (lightly soiled items).

RINSE HOLD

PREWASH

DAILY / SUPER

QUICK

EXTRA RINSE

Sintetici

60° - Cold

Main wash - Rinses

Maximum spin speed 900 rpm

Max. load 3,5 kg - Reduced load 2 kg

Synthetic or mixed fabrics: underwear, coloured gar-

ments, non-shrink shirts, blouses.

SPIN REDUCTION

RINSE HOLD

PREWASH

DAILY / SUPER

QUICK

EXTRA RINSE

Delicati

40° - 30°

Main wash - Rinses

Maximum spin speed 700 rpm

Max. load 3,5 kg - Reduced load 2 kg

Delicate fabrics: acrylics, viscose, polyester.

SPIN REDUCTION

RINSE HOLD

PREWASH

DAILY / SUPER

QUICK

EXTRA RINSE

Lana/A mano

40° - Cold

Main wash - Rinses

Maximum spin speed 900 rpm

Max. load 2 kg

Washing programme for machine washable wool as well

as for hand washable woollens and delicate fabrics with

«hand washing» care symbol. Note : A single or bulky item

may cause imbalance. If the appliance doesn’t perform the

final spin phase, add more items, redistribute the load

manually and then select the spinning programme.

SPIN REDUCTION

RINSE HOLD

electrolux 15

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

Risciacquo

Rinse - Long spin

Maximum spin speed

Max. load 8 kg

With this programme it is possible to rinse and spin cotton

garments which have been washed by hand. To intensify

the rinsing action, select the option EXTRA RINSE. The

appliance will add some additional rinses.

SPIN REDUCTION

RINSE HOLD

EXTRA RINSE

Scarico

Draining of water

Max. load 8 kg

For emptying out the water of the last rinse in programmes

with the Rinse Hold option set.

Centrifuga

Drain and long spin

Maximum spin speed

Max. load 8 kg

Separate spin for hand washed garments and after pro-

grammes with the Rinse Hold option set. If needed, re-

duce the spin speed to adapt it to the fabrics to be spun.

SPIN REDUCTION

Miniprogram

30°

Main wash - Rinses

Maximum spin speed 700 rpm

Max. load 2 kg

Ideal for laundry which is lightly soiled or which only needs

freshening up.

= OFF

For cancelling the programme which is running or to switch the machine off .

1) If you set the Super Quick option (button 3), we recommend that you reduce the maximum load as indicated. Full

loading is possible however with somewhat reduced cleaning results.

2) If using liquid detergents, a programme without PREWASH must be selected.

3) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these

programmes are respectively the «standard 60 °C cotton programme» and the «standard 40 °C cotton

programme». Set this programme to have a good washing results and decrease the energy consumption. The

time of the washing programme is extended.

The washing temperature of the washing phase may differ from the temperature declared for the selected pro-

gramme.

CONSUMPTION VALUES

The data of this table are approximate. Different causes can change the data: the

quantity and type of laundry, the water and ambient temperature.

Programmes Load

(kg)

Energy con-

sumption

(kWh)

Water con-

sumption (li-

tre)

Approximate

programme

duration (mi-

nutes)

Remaining

moisture

(%)

Cottons 60 °C 8 1.40 63 160 60

16 electrolux

Programmes Load

(kg)

Energy con-

sumption

(kWh)

Water con-

sumption (li-

tre)

Approximate

programme

duration (mi-

nutes)

Remaining

moisture

(%)

Cottons 40 °C 8 0.60 63 130 60

Synthetics 40 °C 3,5 0.60 54 80 37

Delicates 40 °C 3.5 0.60 63 65 37

Wool/Hand wash

30 °C

2 0.25 55 60 32

Standard cotton programmes

Standard 60 °C

cotton

8 1.17 61 205 60

Standard 60 °C

cotton

4 0.77 48 159 60

Standard 40 °C

cotton

4 0.69 48 161 60

1) At the end of spin phase.

Off Mode (W) Left On Mode (W)

0.98 0.10

The information given in the charts above are in compliance with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC.

CARE AND CLEANING

Warning! You must disconnect the

appliance from the electricity supply,

before you can carry out any cleaning

or maintenance work.

Descaling

The water we use normally contains lime. It

is a good idea to periodically use a water

softening powder in the machine. Do this

separately from any laundry washing, and

according to the softening powder manu-

facturer's instructions. This will help to pre-

vent the formation of lime deposits.

After each wash

Leave the door open for a while. This helps

to prevent mould and stagnant smells form-

ing inside the appliance. Keeping the door

open after a wash will also help to preserve

the door seal.

Maintenance wash

With the use of low temperature washes it

is possible to get a build up of residues in-

side the drum.

We recommend that a maintenance wash

be performed on a regular basis.

To run a maintenance wash:

• The drum should be empty of laundry.

• Select the hottest cotton wash pro-

gramme.

• Use a normal measure of detergent,

must be a powder with biological proper-

ties.

External cleaning

Clean the exterior cabinet of the appliance

with soap and water only, and then dry

thoroughly.

Important! Do not use methylated spirits,

solvents or similar products to clean the

cabinet.

Cleaning the dispenser drawer

The detergent dispenser drawer should be

cleaned regularly.

The washing powder and additive dispens-

er drawer should be cleaned regularly.

Remove the drawer by pressing the catch

downwards and by pulling it out.

electrolux 17

Flush it out under a tap, to remove any

traces of accumulated powder.

To aid cleaning, the top part of the additive

compartment should be removed. Clean all

parts with water.

Clean the chamber of dispenser drawer

with a brush.

Washing drum

Rust deposits in the drum may occur due

to rusting foreign bodies in the washing or

tap water containing iron.

Important! Do not clean the drum with

acidic descaling agents, scouring agents

containing chlorine or iron or steel wool.

1. Remove any rust deposits on the drum

with a cleaning agent for stainless steel.

2. Run a washing cycle without any wash-

ing to clean off any cleaning agent resi-

dues.

Programme: Short Cotton Programme

at maximum temperature and add ap-

prox. 1/4 measuring cup of detergent.

Door seal

Check from time to time the door seal and

eliminate eventual possible objects that

could be trapped in the fold.

Drain pump

Regularly examine the drain pump and

make sure that it is clean.

Clean the pump regularly and/or if:

• The appliance does not drain the water.

• The drum cannot turn.

• The appliance makes an unusual noise

because of the blockage of the drain

pump.

• A problem with water draining is detected

(see chapter “What to do if...” for more

details).

Warning!

1. Disconnect the mains plug from

the mains socket.

2. Do not remove the filter while the

appliance operates. Do not clean

the drain pump if the water in the

appliance is hot. The water must

be cold before you clean the drain

pump.

To clean the drain pump:

1. Open the pump door.

18 electrolux

2. Put a container below the recess of the

drain pump to collect the water that

flows out.

3. Press the two levers and pull forward

the drainage duct to let the water flow

out.

4. When the container is full of water, put

the drainage duct back again and emp-

ty the container. Do steps 3 and 4

again and again until no more water

flows out from the drain pump.

5. Pull back the drainage duct.

6. Unscrew the filter and remove it.

7. Remove fluff and objects from the

pump.

8. Make sure that the impeller of the

pump can turn. If this does not occur,

contact the service centre.

9. Clean the filter under the water tap and

put it back in the pump into the special

guides.

10. Make sure that you tighten correctly the

filter to prevent leakages.

11. Close the drain pump door.

Warning!

Never remove the pump cover during a

wash cycle, always wait until the appliance

has finished the cycle, and is empty. When

refitting the pump cover, ensure it is se-

curely re-tightened so as to stop leaks and

young children being able to remove it.

Cleaning the water inlet filters

If you notice that the machine is taking lon-

ger to fill, check that the filter in the water

inlet hose is not blocked.

1. Turn off the water tap.

2. Unscrew the water inlet hose.

electrolux 19

3. Clean the filter in the hose using a hard

bristle brush.

4. Screw the hose back onto the tap.

5. Unscrew the hose from the machine.

Keep a rug nearby because some wa-

ter may flow.

6. Clean the filter in the valve with a stiff

brush or with the piece of cloth.

7. Screw the hose back to the machine

and make sure the connection is tight.

8. Turn on the water tap.

Emergency emptying out

If the appliance cannot drain the water, pro-

ceed as follows to empty out the machine:

1. pull out the plug from the power sock-

et;

2. close the water tap;

3. if necessary, wait until the water has

cooled down;

4. open the pump door;

5. place a container on the floor below the

recess of the drain pump;

6. press the two levers and pull forward

the drainage duct to let the water flow

out;

7. when the container is full of water, put

the drainage duct back again and emp-

ty the container;

repeat this operation until water stops

flowing out;

8. if necessary clean the pump (refer to

the section ‘Drain pump’ );

9. close the drain pump door.

When you drain the water with the emer-

gency drain procedure, you must activate

again the drain system:

1. Put 2 litres of water in the main wash

compartment of the detergent dispens-

er.

2. Start the programme to drain the wa-

ter.

Frost precautions

If the machine is installed in a place where

the temperature could drop below 0°C, re-

move the remaining water from the inlet

hose and the drain pump.

1. disconnect the mains plug from the

mains socket.

2. close the water tap

3. unscrew the water inlet hose from the

tap;

4. put the two ends of the inlet hose in a

container and let the water flow out of

the hose.

5. empty the drain pump as described in

the ‘Emergency drain’ section.

6. when the drain pump is empty, install

the water inlet hose again.

Warning!

Make sure that the temperature is more

than 0 °C before you use the appliance

again.

The manufacturer is not responsible for

damages caused by low temperatures.

WHAT TO DO IF…

Certain problems are due to lack of simple

maintenance or oversights, which can be

solved easily without calling out an engi-

neer. Before contacting your local Service

Centre, please carry out the checks listed

below.

During machine operation it is possible that

the red pilot light of button 6 blinks, one of

the following alarm codes appears on the

display and at the same some acoustic sig-

nals sound every 20 seconds to indicate

that the machine is not working:

•

: problem with the water supply.

20 electrolux

Page is loading ...

ELECTROLUX-REX RWF108315W User manual

Brand: ELECTROLUX-REX

Model: RWF108315W

Category: Washing machines

Type: User manual

Download PDF

report

ELECTROLUX-REX RWF108315W User manual

ELECTROLUX-REX RWF108315W User manual

Related papers