AT&T 1440 User manual

Please also read

Part 1 — Important

Product Information

USER’S MANUAL

Pa rt 2

AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones.

2.4 GHz Cordless Telephone with

Caller ID/Call Waiting 14 4 0

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page II

AT&T and the Globe Design are

trademarks of AT&TCorp., licensed to

Advanced American Telephones.

Printed in China. Issue 1AT&T 12/02

Visit us at www.telephones.att.com

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page III

CONTENTS

BEFORE YOU BEGIN . . . . . . . . 1

Parts List . . . . . . . . . . . . . . . . . . 1

Choose a Location for Your

Phone . . . . . . . . . . . . . . . . . . 2

About Caller Identification . . . . . . 2

INSTALLATION . . . . . . . . . . . . 3

Before You Install . . . . . . . . . . . . 3

Table/Desk Installation . . . . . . . . 4

Wall Installation . . . . . . . . . . . . . 6

TELEPHONE OPERATION . . . . . . 7

Make a Call . . . . . . . . . . . . . . . . 7

Answer a Call . . . . . . . . . . . . . . 7

End a Call . . . . . . . . . . . . . . . . . 7

Change Channel . . . . . . . . . . . . . 7

Redial . . . . . . . . . . . . . . . . . . . . 7

Handset Volume . . . . . . . . . . . . . 7

Flash/Call Waiting . . . . . . . . . . . . 7

Hold . . . . . . . . . . . . . . . . . . . . . 7

Page/Handset Locator . . . . . . . . 8

Handset Ringer Style/

Battery Save . . . . . . . . . . . . . . 9

Temporary Tone Dialing . . . . . . .9

Headset Jack . . . . . . . . . . . . . . .10

Operating Range . . . . . . . . . . . . 10

TELEPHONE MEMORY . . . . . . 11

Store a Number/Name

in Memory . . . . . . . . . . . . . . 11

Edit a Number/Name Stored

in Memory . . . . . . . . . . . . . . 14

Delete a Number/Name Stored

in Memory . . . . . . . . . . . . . . 15

Dial a Memory Number . . . . . . . 16

TELEPHONE DIRECTORY . . . . . 17

Store a Number/Name in

the Directory . . . . . . . . . . . . . 17

Edit a Number/Name Stored

in the Directory . . . . . . . . . . . 19

Delete a Number/Name Stored

in the Directory . . . . . . . . . . . 20

Dial a Number from

the Directory . . . . . . . . . . . . . 21

CALLER ID OPERATION . . . . . . 22

About Call History . . . . . . . . . . 22

Review Call History . . . . . . . . . . 23

Turn Off Base

NEW CALL Indicator . . . . . . . 23

Delete Records from

Call History . . . . . . . . . . . . . . 24

Dial a Displayed Number . . . . . 25

Store a Call History Record

in the Directory . . . . . . . . . . . 26

Display Screen Messages . . . . . . 27

BATTERIES . . . . . . . . . . . . . . 28

Charge the Handset

Battery Pack . . . . . . . . . . . . . .28

Replace the Handset

Battery Pack . . . . . . . . . . . . . 29

IN CASE OF DIFFICULTY . . . . . 30

DEFAULT SETTINGS . . . . . . . . 34

TECHNICAL SPECIFICATIONS . . 35

INDEX . . . . . . . . . . . . . . . . . 36

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page IV

1

BEFORE YOU BEGIN

P a rts List

Your box should include:

This User’s

Manual

NiCd

battery pack

Base unit

Handset

2 Telephone

line cords

Power

adapter

Wall

Bracket

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 1

Choose a Location for Your Phone

For best reception quality, choose a location for the base unit of your

new telephone:

• Away from microwave ovens

• Away from TVs, VCRs, stereo equipment and computers

(Cordless telephones operate at a radio frequency that may cause

i n t e r fe re n ce with these types of equipment.)

• Away from extreme heat or cold (For example: radiators, direct

sunlight, air ducts, air conditioning and open windows)

• Away from other cordless telephones (Note: 2.4 GHz Digital

Spread Spectrum Telephones may cause interference with this

telephone.)

• Away from metal walls or cabinets, and

• Near an electrical outlet not controlled by a wall switch.

About Caller Identification (Caller ID)

This product has a Caller ID with Call Waiting feature that works with

service from your local phone service provider.

Caller ID with Call Waiting lets you see who’s calling before you answer

the phone,even when you’re on another call.

You may need to change your phone service to use this feature. Contact

your phone service provider if:

• You have both Caller ID and Call Waiting, but as separate

services (you may need combined service)

• You have only Caller ID service, or only Call Waiting service

• You don’t subscribe to any Caller ID or Call Waiting services.

You can use this product with regular Caller ID service,and you can use

this product’s other features without subscribing to either Caller ID or

combined Caller ID with Call Waiting service.

There are fees for Caller ID services, and they may not be available in all

areas.

This product can provide information only if both you and the caller are

in areas offering Caller ID service, and if both telephone companies use

compatible equipment.

2

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 2

INSTALLATION

Before You Install

1 Choose a location for the base near an electrical outlet and a

telephone jack.

This phone requires a modular telephone jack and a standard

electrical outlet (110v AC) not controlled by a wall switch.

2 Install the handset battery.

Use only the following AT&T Batteries 3301, SKU#91076.

3

b) Align two holes in

plug with socket

pins, and snap the

plug into place.

d) Replace

cover by

sliding it up

into place.

c) Place battery pack

in compartment

with the wires in

the lower left

corner,along the

bottom of the

battery pack.

a) Remove battery

compartment

cover by pressing

on the

indentation

and sliding

downward.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 3

4

3 Attach belt clip to the cordless handset (optional).

To attach

To re m ove

Table/Desk Installation

Standard

electrical outlet

Modular

telephone

jack

1 Connect the

telephone

line cord.

2 Connect the

power cord.

¥

NOTE: Install the base unit away from electronic equipment

such as personal computers, television sets or microwave ovens.

Avoid excessive heat, cold, dust or moisture.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 4

3 Charge the handset battery.

Place the handset in the base. Charge the battery for at least 12

hours the first time.

4 Check for dial tone.

After the batteries are charged, pick up the handset and press

; you should hear a dial tone.

5 Set the dial mode.

If you have touch tone service, the phone is ready to use as soon as

the batteries are charged.

If you have dial pulse (rotary) service, you’ll need to change the dial

mode.

• Press on the handset to enter programming mode.

• Press or until the screen displays and the

currently selected mode.

• Press . The current setting blinks.

• Press or to select or .

• Press ,to save the displayed mode.

6 Set Time and Date.

• Press ,then press or until the screen

displays: .Press .

• The month is flashing. Press or until the screen displays

the correct month. Press .

• The day is flashing. Press or until the screen displays the

correct day. Press .

• The hour is flashing. Press or until the screen displays the

correct hour. Press .

• The minute is flashing. Press or until the screen displays

the correct minute. Press .

• or is flashing. Press or to choose between and

. Press .

¥

NOTE: You can choose to set the time manually, or you can

allow it to be automatically set with incoming Caller ID

Information.

5

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 5

Wall Installation

1 Connect the telephone line cord.

2 Connect the power cord.

3 Mount the base on the wall.

6

4 Follow Steps 3–6 in Table/Desk Installation.

a) Align holes on

base with

mounting studs

on wall jack.

b) Pull base down

on mounting

studs until it

locks into place.

Modular

telephone jack

Standard

electrical outlet

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 6

7

TELEPHONE OPERATION

Make a Call

Press ,then dial the number

— OR —

Dial the number (use to backspace and correct

digits),then press to call.

Answer a Call

Press any key except .

End a Call

Press

— OR —

Place handset in base.

Change Channel

Press to switch to a clearer channel while

on a call.

R e d i a l

Press ,then press to call last number

dialed (up to 32 digits).

— OR —

Press ,then press to call last number

dialed.While handset idle,press twice to

delete the record.

Handset Vo l u m e

While on a call,press or to adjust volume of

what you hear.A double beep will be sounded when

reach minimum or maximum volume.

Flash/Call Wa i t i n g

1 When you receive a Call Waiting signal,press

/ to connect to the new call.

2 Press / again to return to the

original call.

H o l d

Press to put a call on hold. Press again or

to release hold

— OR —

Pick up an extension phone will release hold and

return the handset to the idle (on hook) mode.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 7

8

F l a s h i n g :

handset is in

use or there is

an incoming

c a l l .

On steadily :

handset is

c h a rging in

b a s e .

F l a s h e s

when you have

u n rev i e wed

call info rm a t i o n .

Page/Handset Locator

Press to page the handset for

up to 60 seconds. Press again

to cancel,or press on

handset.

If you subscribe to

t e l e phone company

voice mail with a

visual message wa i t i n g

s i g n a l , light fl a s h e s

when you have vo i c e

mail wa i t i n g .

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 8

9

Handset Ringer Style/Battery Save

You can select from four different handset ringer styles,or turn the

ringer off and extend the battery life.

1 Make sure the handset is off.

2 Press to enter programming mode.

3 Press or until the screen displays and the

current setting.

4 Press . The current setting is flashing.

5 Press or to select , , , ,or . You will hear a

sample of each ring.

6 Press to choose the displayed ringer setting.

Temporary Tone Dialing

If you have dial pulse (rotary) service,you can change from dial pulse

to touch tone dialing during a call by pressing . This is useful if

you need to send touch tone signals for access to telephone banking or

long-distance services.

1 Dial the number.

2 Press . Buttons pressed after this send touch tone signals.

3 After you hang up,the phone automatically returns to

dial pulse (rotary) service.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 9

1 0

Operating Range

This cordless telephone operates within the maximum power allowed

by the Federal Communications Commission (FCC). Even so, this

handset and base can communicate over only a certain distance —

which can vary with the locations of the base and handset, the weather,

and the construction of your home or office. For best performance,

keep the base antenna fully upright.

If you receive a call while you are out of range, the handset might

not ring — or if it does ring,the call might not connect when you press

. Move closer to the base,then press to answer the call.

If you move out of range during a phone conversation, you might

hear noise or interference. To improve reception,move closer to the

base.

If you move out of range without pressing ,your phone will be

left “off the hook.” To hang up properly, walk back into range,

periodically pressing .

Headset Jack

You can use this telephone hands-free when

you install anyAT&T 2.5 mm headset,

purchased separately.

Plug the headset into the jack located

on the right side of the handset

(under the small rubber flap).

Do not force the connection,

but make sure the plug

fits securely.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 10

TELEPHONE MEMORY

1 1

This cordless phone can store 10 telephone numbers

with names, each up to 16 digits long in memory

locations you assign (0-9).

¥

NOTE: Press at any time to exit memory

dial mode.

This cordless phone can store an additional 40

telephone numbers with names alphabetically in the

directory. See TELEPHONEDIRECTORY for

instructions.

Store a Number/Name in Memory

1 P ress . Then press or until the

s c reen display s

2 Press or . The screen displays

3 Press the key (0-9) for the memory location

where you’re storing this entry. If the selected

location is empty,the screen displays

¥

NOTE: If the location is not empty, the current

entry is displayed along with the choices

after pressing key. Press to

exit memory dial mode and start again, or follow

the instructions to dial, edit or erase the current

entry.

4 Using the chart below,enter up to 15

characters for the name you’re storing with the

number. Use to backspace and make

corrections;use to advance and add a space.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 11

1 2

P re s s e s

Dial Key 1 2 3 4 5 6

1

A B C 2

D E F 3

G H I 4

J K L 5

M N O 6

P Q R S 7

T U V 8

W X Y Z 9

0

*

& ’ , - . #

5 When you finish entering the name, press

or . The screen displays

6 Enter the telephone number. Use to

backspace and make a correction. Press

to store a pause in the dialing

sequence.

—OR—

Press to display the last number

(up to 16 digits) dialed from this phone.

7 Press or to store your entry.

The screen displays

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 12

1 3

8 Press or to change the setting. Choose

(for Yes) if you wish the phone to alert you to

calls from this number by changing to a

distinctive ringing pattern after the first ring.

Choose (for No) for a normal ringing pattern.

9 Press or to confirm your

selection. If you chose in Step 8,a will be

displayed with the memory entry.

10 To add additional memory locations follow

procedures 1-9 again.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 13

1 4

Edit a Number/Name Stored in Memory

1 Press . The screen displays

2 Press the memory location key of the entry

you wish to edit.

3 When the screen displays the number you

want to edit,press . Then press or

until flashes.

4 Press . The screen displays the name and

number. The flashing cursor appears at the

end of the name. Use , and the dial pad

keys to edit the name. Press to move on

to edit the number. Use to backspace and

make a correction.Press to move on to

edit the Distinctive Ring setting.

5 Press to save the edited information.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 14

1 5

Delete a Number/Name Stored in

Memory

1 Press . The screen displays

2 Press the memory location key of the entry

you wish to delete.

3 When the screen displays the number you

want to delete,press . Then press or

until flashes.

4 Press . The screen displays

and the number. The current choice flashes.

5 Press or until flashes.

6 Press .

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 15

1 6

Dial a Memory Number

1 Press . The screen displays

2 Enter the memory location key of the entry

you want to dial.

3 Press to dial the displayed memory

number.

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 16

TELEPHONE DIRECTORY

1 7

This cordless phone can store 40 telephone numbers

with names,each up to 16 digits long. Entries are

stored alphabetically.

¥

NOTE: Press at any time to exit directory.

Store a Number/Name in the Directory

1 Press . The screen displays

2 Press . The screen displays

3 Using the chart below,enter up to 15

characters for the name you’re storing with the

number. Use to backspace and make

corrections;use to advance and add a space.

P re s s e s

Dial Key 1 2 3 4 5 6

1

A B C 2

D E F 3

G H I 4

J K L 5

M N O 6

P Q R S 7

T U V 8

W X Y Z 9

0

*

& ’ , - . #

91-5393-20-00_ATT1440_R0 2003.3.7 10:47 AM Page 17

Page is loading ...

AT&T 1440 User manual

This manual is also suitable for

AT&T 1440 User manual

Related papers

Other documents