Brodit 215503 Datasheet

Brodit
Brand
Brodit
Model
215503
Category
Mounting kits
Type
Datasheet

Brodit 215503

is a versatile mounting solution that allows you to easily switch between different device holders on the same ProClip. This is ideal if you have multiple cell phones or GPS devices that you use in your car, or if you want to be able to move your device holder to different locations within your vehicle.

The MultiMoveClip comes with two adapter plates, which allow it to fit both large and small tilt swivels. This ensures that you can use the MultiMoveClip with any Brodit holder that has a tilt swivel.

To install the MultiMoveClip, simply screw it into place on your ProClip. Then, you can slide your device holder into the MultiMoveClip from above. To remove the device holder, simply press the latch on the upper part of the MultiMoveClip forward and push the holder upward and out of the MultiMoveClip.

Brodit 215503

is a versatile mounting solution that allows you to easily switch between different device holders on the same ProClip. This is ideal if you have multiple cell phones or GPS devices that you use in your car, or if you want to be able to move your device holder to different locations within your vehicle.

The MultiMoveClip comes with two adapter plates, which allow it to fit both large and small tilt swivels. This ensures that you can use the MultiMoveClip with any Brodit holder that has a tilt swivel.

To install the MultiMoveClip, simply screw it into place on your ProClip. Then, you can slide your device holder into the MultiMoveClip from above. To remove the device holder, simply press the latch on the upper part of the MultiMoveClip forward and push the holder upward and out of the MultiMoveClip.

13 February, 2012, www.brodit.com, © 2012 Brodit AB
Product 215503
215503 MoveClip MultiMoveClip: Complete set. Contains 1 MultiMoveClip, 2 adapter plates, 4 screws.
MultiMoveClip is for you who easily want to switch between different device holders on the same ProClip. Perfect
if you have different cell phones but drive the same car, or if you want to place your GPS where the cell phone
usually sits. You attach the MultiMoveClip onto your ProClip in your car and it is then ready to use with your
device holders of choice. Your device holders are fitted just as secure as if they were screwed directly onto the
ProClip.
MultiMoveClip fits with all Brodit's holders with tilt swivel. There are two sizes of tilt swivels and to be able to fit
even the smaller size two adapter plates are enclosed with the delivery. Combined with item no 215504
MultiMoveClip also fits holders without tilt swivel.
EAN: 7320282155032
1(2)
1. 2.
INSTALLATION INSTRUCTIONS
4.3.
Please read all of the instructions and look at the pictures before attaching the holder. There are two tilt swivel
sizes. The larger tilt swivel will fit directly into the MultiMoveClip. In order for the smaller tilt swivel to fit into the
MultiMoveClip you need to use the enclosed adapter plate. Compare the tilt swivel on your holder with the drawn
picture to determine which size tilt swivel you have. To make sure, you can always place your holder into the
MultiMoveClip without using an adapter plate; if the fit is loose or unstable, you will need to use the adapter plate.
1. If you have the smaller tilt swivel: Press the adapter plate into place onto the tilt swivel.
2. Place the MultiMoveClip onto the desired position and screw it into place with the enclosed screws.
3. To place the holder into the MultiMoveClip: Slide the holder downward into place from above.
To remove the holder from the MultiMoveClip: Press the latch on the upper part of the MultiMoveClip forward. In
the same time push the holder upward and out of the MultiMoveClip.
4. MultiMoveClip is in place. You can now switch holders easily.
2(2)
  • Page 1 1
  • Page 2 2

Brodit 215503 Datasheet

Brodit
Brand
Brodit
Model
215503
Category
Mounting kits
Type
Datasheet

Brodit 215503

is a versatile mounting solution that allows you to easily switch between different device holders on the same ProClip. This is ideal if you have multiple cell phones or GPS devices that you use in your car, or if you want to be able to move your device holder to different locations within your vehicle.

The MultiMoveClip comes with two adapter plates, which allow it to fit both large and small tilt swivels. This ensures that you can use the MultiMoveClip with any Brodit holder that has a tilt swivel.

To install the MultiMoveClip, simply screw it into place on your ProClip. Then, you can slide your device holder into the MultiMoveClip from above. To remove the device holder, simply press the latch on the upper part of the MultiMoveClip forward and push the holder upward and out of the MultiMoveClip.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers