SUGGESTED SPECIFICATIONS: _______________ projection screen(s), __________ (H) x ____________ (W), electrically operated 120 volt
(60Hz), not more than 2.4 amp with a quick connect male plug-in connector on the motor. Shall have specially designed motor mounted
inside the roller, to be three wire with ground, quick reversal type, oiled for life, with automatic thermal overload cutout, integral gears,
capacitor and an electric brake to prevent coasting. To have preset but adjustable limit switches to automatically stop picture surface in
the “up” and “down” positions. Junction box shall be externally integrated into the housing making it possible to install the housing and
wire to the building’s electrical system during construction. The junction box shall contain a quick connect connector that is mounted in
the housing for easy plug-in connection to the motorized fabric and roller assembly. The roller to be of rigid metal. The motorized fabric
and roller assembly to be installed in the case at the factory or at a later time at the job site. Roller mounting brackets to be adjustable to
allow centering or offsetting of the screen within the case. Screen to be designed for left or right-hand motor installation. Screen fabric
to be flame retardant and mildew resistant fiberglass with black masking borders standard. Bottom of fabric shall be formed into a
pocket holding a metal rod. Heavy duty plastic caps shall protect the ends of the rod. Top, front and back of case to be made of extruded
aluminum powder coated white. End caps to be of heavy gauge steel, powder coated white. Bottom of case to have a removable
access door. Door to be of extruded aluminum powder coated white. Bottom of case to be self-trimming, with a built-in flange around
the bottom of the case. To be complete with a three-position control switch and cover plate. Suitable for use in environmental air space
in accordance with section 300-22 (c) of the National Electric Code, and sections 2-128, 12-010 (3) and 12-100 of the Canadian Electrical
Code, part 1, CSA C22.1. Screen to be listed by Underwriters’ Laboratories.
Matte White:
Horizontal seam required when both dimensions exceed 10'.
High Contrast Matte White: Available in sizes where both dimensions
do not exceed 10'.
Video Spectra 1.5 : Available in sizes where both dimensions do not
exceed 8'.
Silver Lite 2.5 : Available in sizes up to and including 8' x 8'.
High Power
®
and High Contrast High Power
®
: Available in sizes up
to and including 9' x 12'. Horizontal seam required when both
dimensions exceed 8'.
WHEN ORDERING, MARK APPROPRIATE SELECTIONS:
Select size from charts on the other side.
Select viewing surface:
o Matte White
o High Contrast Matte White
o High Power
®
o High Contrast High Power
®
o Video Spectra 1.5
o Silver Lite 2.5
GREENGUARD
®
and GREENGUARD
®
Children and Schools Certified.
Optional Accessories:
o Extra Drop available to lower picture area more than normal.
Specify total drop at top _____ (black or white) or at bottom
_____ (black or white). 13' maximum total surface height
including picture area.
o Single Motor Low Voltage Control (LVC) - external.
o Single Motor Low Voltage Control (LVC) - built-in.
o Wireless Remote Control for LVC.
o Radio Frequency Remote.
o Radio Frequency Range Extender available
o Infrared Remote.
o Silent Motor.
o Silent Motor with Integrated LVC.
o Key Locking Cover Plate for 120V or LVC Switch.
o Key Operated Switch for 120V only (NOTE: Cannot be used
with LVC).
o No Borders (Black masking borders standard).
o 220 Volt (50 Hz) Motor.
o Video Projector Interface Control - external.
o Video Projector Interface Control - built-in (Adds 10" to case
length on 220V motor only).
o SCB-100 RS-232 Serial Control Board - external.
o NET-100 Ethernet-Serial Adapter
o SCB-100 RS-232 Serial Control Board - built-in. (adds 10" to
overall length of case)
o NET-100 Ethernet-Serial Adapter
o SCB-200 RS-232 Serial Control Board - built-in only. (adds 10"
to overall length of case)
o NET-200 Ethernet-Serial Adapter
o WC-200 Wall Controller
o IR-200 Infrared Remote
SPECIFICATION DATA
ADVANTAGE
®
ELECTROL
®
Automatic Electric Projection Screen Model
ELECTRICAL
JUNCTION BOX
MOTOR END
VARIABLE POSITION
MOUNTING BRACKET
AUDIENCE
SIDE
3
⁄8" THREADED ROD
(NOT SUPPLIED)
HANGER BRACKET
SEE DETAIL A
7
3
⁄4"
DETAIL A
7
15
⁄16"
3
7
⁄16"
6
1
⁄16"
3
⁄8" THREADED ROD
(NOT SUPPLIED)
ATTACHED TO
HANGER BRACKET
SELF-TRIMMING
FLANGE
6
3
⁄8"
7
3
⁄4"
FINISHED
CEILING
8"
SUGGESTED METHODS OF INSTALLATION
7
3
⁄4"
6
1
⁄16"
6
3
⁄8"
6
3
⁄8"
DA-LITE SCREEN COMPANy LLC
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
P 800-622-3737 / 574-267-8101
F 877-325-4832 / 574-267-7804
www.da-lite.com