Supero 6015B-NTR User manual

USER’S MANUAL

1.0c

SUPER

®

SUPERSERVER 6015B-UR

S

UPERSERVER 6015B-U

S

UPERSERVER 6015B-NTR

SUPERSERVER 6015B-NT

Manual Revision 1.0c

Release Date: February 21, 2008

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software, if any,

and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or

reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for

all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It pro-

vides information for the installation and use of the SuperServer 6015B-UR/6015B-

U/6015B-NTR/6015B-NT. Installation and maintenance should be performed by

experienced technicians only.

The SuperServer 6015B-UR/6015B-U/6015B-NTR/6015B-NT is a high-end server

based on the SC815TQ-R650U/SC815TQ-560U 1U rackmount chassis and the Su-

per X7DBU, a dual processor serverboard that supports Intel

®

Xeon

®

5300/5100/5000

series processors at a Front Side (System) Bus speed of 1333/1066/667 MHz and

up to 32 GB of ECC FBD DDR2-667/533 SDRAM.

Manual Organization

Chapter 1: Introduction

The ﬁ rst chapter provides a checklist of the main components included with the

server system and describes the main features of the X7DBU serverboard and

the SC815TQ-R650U/SC815TQ-560U chassis, which comprise the SuperServer

6015B-UR/6015B-U/6015B-NTR/6015B-NT.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 6015B-UR/

6015B-U/6015B-NTR/6015B-NT into a rack and check out the server conﬁ guration

prior to powering up the system. If your server was ordered without processor and

memory components, this chapter will refer you to the appropriate sections of the

manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

SUPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

iv

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

SuperServer 6015B-UR/6015B-U/6015B-NTR/6015B-NT.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X7DBU serverboard, including the

locations and functions of connections, headers and jumpers. Refer to this chapter

when adding or removing processors or main memory and when reconﬁ guring the

serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC815TQ-R650U/SC815TQ-

560U server chassis. You should follow the procedures given in this chapter when

installing, removing or reconﬁ guring SATA or peripheral drives and when replacing

system power supply modules and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup Utility.

Appendix A: BIOS POST Messages

Appendix B: BIOS POST Codes

Appendix C: Software Installation

Appendix D: System Speciﬁ cations

v

Preface

Notes

vi

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

1-3 Server Chassis Features ................................................................................ 1-3

1-4 Contacting Super Micro .................................................................................. 1-6

Chapter 2: Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System ................................................................................... 2-1

2-3 Preparing for Setup ........................................................................................ 2-1

Choosing a Setup Location ...................................................................... 2-2

Rack Precautions ..................................................................................... 2-2

Server Precautions ................................................................................... 2-2

Rack Mounting Considerations ................................................................ 2-3

2-4 Installing the System into a Rack ................................................................... 2-4

2-5 Checking the Serverboard Setup ................................................................... 2-8

2-6 Checking the Drive Bay Setup ..................................................................... 2-10

Chapter 3: System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons .................................................................................... 3-1

UID ........................................................................................................... 3-1

Reset ........................................................................................................ 3-1

Power ....................................................................................................... 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Universal Information LED ....................................................................... 3-2

NIC2 ......................................................................................................... 3-3

NIC1 ......................................................................................................... 3-3

HDD .......................................................................................................... 3-3

Power ....................................................................................................... 3-3

3-4 SATA Drive Carrier LEDs ............................................................................... 3-3

SUPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

Chapter 4: System Safety

4-1 Electrical Safety Precautions .......................................................................... 4-1

4-2 General Safety Precautions ........................................................................... 4-2

4-3 ESD Precautions ............................................................................................ 4-3

4-4 Operating Precautions .................................................................................... 4-4

Chapter 5: Advanced Serverboard Setup

5-1 Handling the Serverboard .............................................................................. 5-1

5-2 Processor and Heatsink Installation ............................................................... 5-2

5-3 Connecting Cables ......................................................................................... 5-5

Connecting Data Cables .......................................................................... 5-5

Connecting Power Cables ....................................................................... 5-5

Connecting the Control Panel .................................................................. 5-5

5-4 I/O Ports ......................................................................................................... 5-6

5-5 Installing Memory ........................................................................................... 5-7

5-6 Adding PCI Cards ........................................................................................... 5-9

5-7 Serverboard Details ...................................................................................... 5-10

X7DBU Layout ....................................................................................... 5-10

X7DBU Quick Reference ....................................................................... 5-11

5-8 Connector Deﬁ nitions ................................................................................... 5-12

ATX Power Connector ........................................................................... 5-12

Auxiliary Power Connector ..................................................................... 5-12

Processor Power Connector .................................................................. 5-12

NMI Button ............................................................................................. 5-12

Power LED ............................................................................................. 5-12

HDD LED ............................................................................................... 5-13

NIC1 LED ............................................................................................... 5-13

NIC2 LED ............................................................................................... 5-13

Universal Information LED ..................................................................... 5-13

Power Fail LED ...................................................................................... 5-14

Reset Button .......................................................................................... 5-14

Power Button .......................................................................................... 5-14

Universal Serial Bus (USB0/1) ............................................................... 5-14

Universal Serial Bus Headers ................................................................ 5-15

Serial Ports ............................................................................................. 5-15

Fan Headers .......................................................................................... 5-15

Chassis Intrusion .................................................................................... 5-16

Power LED/Speaker ............................................................................... 5-16

ATX PS/2 Keyboard and PS/2 Mouse Ports ......................................... 5-16

vii

Table of Contents

viii

Overheat LED ........................................................................................ 5-16

Wake-On-LAN ........................................................................................ 5-17

Wake-On-Ring ........................................................................................ 5-17

SMB ........................................................................................................ 5-17

SMBUS_PS ............................................................................................ 5-17

JLAN 1/2 (Ethernet Ports) ...................................................................... 5-18

Alarm Reset ........................................................................................... 5-18

SGPIO .................................................................................................... 5-18

5-9 Jumper Settings ............................................................................................ 5-19

Explanation of Jumpers ......................................................................... 5-19

CMOS Clear ........................................................................................... 5-19

VGA Enable/Disable ............................................................................... 5-19

LAN Enable/Disable ............................................................................... 5-20

Watch Dog Enable/Disable .................................................................... 5-20

I

2

C Enable/Disable ................................................................................. 5-20

5-10 Onboard Indicators ....................................................................................... 5-21

LAN1/2 LEDs ......................................................................................... 5-21

LE1 ......................................................................................................... 5-21

LE2 ......................................................................................................... 5-21

5-11 Floppy, IDE and SATA Drive Connections ................................................... 5-22

Floppy Connector ................................................................................... 5-22

IDE Connector ........................................................................................ 5-23

SATA Ports ............................................................................................. 5-23

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................. 6-1

6-2 Control Panel .................................................................................................. 6-2

6-3 System Fans ................................................................................................... 6-3

System Fan Failure .................................................................................. 6-3

Replacing System Fans ........................................................................... 6-3

6-4 Drive Bay Installation/Removal ...................................................................... 6-4

6-5 Power Supply ................................................................................................. 6-9

6015B-UR/6015B-NTR: Power Supply Failure ........................................ 6-9

6015B-UR/6015B-NTR: Removing/Replacing the Power Supply ............ 6-9

6015B-U/6015B-NT: Power Supply Failure ............................................ 6-10

6015B-U/6015B-NT: Removing/Replacing the Power Supply ............... 6-10

SUPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

Table of Contents

ix

Chapter 7: BIOS

7-1 Introduction ..................................................................................................... 7-1

7-2 Running Setup ................................................................................................ 7-2

7-3 Main BIOS Setup ............................................................................................ 7-2

7-4 Advanced Setup ............................................................................................. 7-7

7-5 Security ......................................................................................................... 7-23

7-6 Boot .............................................................................................................. 7-24

7-7 Exit ................................................................................................................ 7-25

Appendices:

Appendix A: BIOS POST Messages

Appendix B: BIOS POST Codes

Appendix C: Software Installation

Appendix D: System Speciﬁ cations

Notes

x

S

UPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

Chapter 1

Introduction

1-1 Overview

The SuperServer 6015B-UR/6015B-U/6015B-NTR/6015B-NT is a high-end server

comprised of two main subsystems: the SC815TQ-R650U (6015B-UR/6015B-

NTR)/SC815TQ-560U (6015B-U/6015B-NT) 1U server chassis and the X7DBU dual

processor serverboard. Please refer to our web site for information on operating

systems that have been certiﬁ ed for use with the system (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have been

included with the 6015B-UR/6015B-U/6015B-NTR/6015B-NT, as listed below:

 One (1) slim DVD-ROM drive [DVM-PNSC-824(B)]

 Four (4) sets of 4-cm counter-rotating fans (FAN-0086L)

 One (1) IDE cable (CBL-0139L)

 Two (2) passive CPU heatsinks (SNK-P0017)

 Riser Cards: (see Section 5-6 for details)

One (1) RSC-R1UU-XR for PCI-X card (pre-installed)

One (1) RSC-R1UU-E8R for PCI-X card (in accessory box)

One (1) CSE-R1UU-UE8 for PCI-E card (6015B-UR/6015B-U only)

One (1) CSE-R1UU-2E8 for two PCI-E cards (6015B-NTR/6015B-NT only)

 SATA Accessories

One (1) SATA backplane (BPN-SAS-815TQ)

One (1) SATA iPASS cable (CBL-0188L) (6015B-UR/6015B-U only)

Four (4) SAS drive carriers (MCP-220-00001-01)

One (1) SATA cable (CBL-0190L) (6015B-NTR/6015B-NT only)

One (1) SGPIO cable (CBL-0157) (6015B-NTR/6015B-NT only)

 One (1) rackmount kit (CSE-PT51L)

 One (1) CD containing drivers and utilities

 SuperServer 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

Note: a "V" at the end of a server name indicates the chassis is silver.

Chapter 1: Introduction

1-1

1-2

S

UPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

1-2 Serverboard Features

At the heart of the SuperServer 6015B-UR/6015B-U/6015B-NTR/6015B-NT lies

the X7DBU, a dual processor serverboard based on Intel's 5000P chipset. Below

are the main features of the X7DBU (see Figure 1-1 for a block diagram of the

chipset).

Processors

The X7DBU supports single or dual 771-pin Intel Xeon 5300/5100/5000 series pro-

cessors at a FSB speed of 1333/1066/667 MHz. Please refer to the serverboard

description pages on our web site for a complete listing of supported processors.

Memory

The X7DBU has eight 240-pin DIMM sockets that can support up to 32 GB of ECC

FBD (Fully Buffered DIMM) DDR2-667 or DDR2-533 SDRAM. The memory is an

interleaved conﬁ guration, which requires modules of the same size and speed to be

installed in pairs. Please refer to Chapter 5 for memory speed jumper settings.

UIO (6015B-UR/6015B-U)

The X7DBU is a specially-designed serverboard that features Supermicro's UIO

(Universal I/O) technology. UIO serverboards have a PCI-Express x8 connector

that can support any one of several types of UIO card types to add SAS ports,

additional LAN ports, etc. to the serverboard. This allows the user to tailor the

serverboard to their own needs. Note: the 6015B-UR/6015B-U does not come

with a UIO card installed.

Serial ATA

An on-chip (ESB2) SATA controller is integrated into the X7DBU to provide a

six-port, 3 Gb/sec Serial ATA subsystem, which is RAID 0, 1 and 10 supported.

The SATA drives are hot-swappable units. Note: The operating system you use

must have RAID support to enable the hot-swap capability and RAID function of

the Serial ATA drives.

Onboard Controllers/Ports

One ﬂ oppy drive controller and one onboard ATA/100 controller are provided to

support up to two IDE hard drives or ATAPI devices. The color-coded I/O ports

include one COM port, a VGA (monitor) port, two USB 2.0 ports, PS/2 mouse and

keyboard ports and two gigabit Ethernet ports.

1-3

Chapter 1: Introduction

ATI Graphics Controller

The X7DBU features an integrated ATI video controller based on the ES1000 graph-

ics chip. The ES1000 was designed speciﬁ cally for servers, featuring low power

consumption, high reliability and superior longevity.

Other Features

Other onboard features that promote system health include onboard voltage moni-

tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

1-3 Server Chassis Features

The 6015B-UR/6015B-NTR is built upon the SC815TQ-R650U chassis while the

6015B-U/6015B-NT is built upon the SC815TQ-560U chassis. The following is a

general outline of the main features of both chassis.

System Power

The SC815TQ-R650U features a redundant 650W power supply consisting of two

power modules. The system does not need to be shut down when replacing or

removing a single power supply module. The SC815TQ-560U features a single

560W power supply module. The system must be shut down when replacing or

removing this power supply module.

SATA Subsystem

The SC815TQ-R650U/SC815TQ-560U chassis was designed to support four hot-

swap SATA hard drives. Note: In the 6015B-NTR/6015B-NT, SATA drives are

connected to the onboard SATA ports.

PCI Expansion Slots

6015B-UR/6015B-U: A riser card on the right side of the chassis can support either

one PCI-X 133 card or one PCI-E x8 card. The left side supports a UIO card and

one PCI-E x8 card.

6015B-NTR/6015B-NT: A riser card on the right side of the chassis can support

either one PCI-X 133 card or one PCI-E x8 card. The left side supports two PCI-E

x8 cards. See section 5-6 for details. (Right and left refer to the side when viewed

from the front of the system. The 6015B-NTR/6015B-NT does not support a UIO

card.)

1-4

S

UPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

Front Control Panel

The chassis' control panel provides you with system monitoring and control. LEDs

indicate system power, HDD activity, network activity (two) and UID/overheat/fan

fail/power fail. A main power button and system reset button is also included.

I/O Backplane

The SC815TQ-R650U/SC815TQ-560U is an extended ATX form factor chassis that

is designed to be used in a 1U rackmount conﬁ guration. Ports on the I/O backplane

include one COM port, a VGA port, two USB 2.0 ports, PS/2 mouse and keyboard

ports and two gigabit Ethernet ports. A UID (Unit Identiﬁ er) button and LED are

also located beside the LAN2 Ethernet port.

Cooling System

The SC815TQ-R650U/SC815TQ-560U chassis has an innovative cooling design

that features four sets of 4-cm counter-rotating fans located in the middle section

of the chassis. There is a "Fan Speed Control Mode" setting in BIOS that allows

chassis fan speed to be determined by system temperature. The power supply

module also includes a cooling fan.

1-5

Chapter 1: Introduction

Figure 1-1. Intel 5000P Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

5000 P

ESB2

CPU #1

PCI-E x8 slot

Gb LAN Ports (2)

SATA Ports (4)

IDE

USB Ports (5)

S I/O

FWH

Kybd/

Mouse

FDD

COM

Ports

CPU #2

FBD CH0

SXB1: PCI-E x16

PCI-X slot

ATI

ES1000

USB 2.0

LPC Bus

DDR2-667/533 ( FBD)

DIMM 1B

DIMM 1A

DIMM 2B

DIMM 2A

DIMM 3B

DIMM 3A

DIMM 4B

DIMM 4A

FBD CH1

FBD CH2

FBD CH3

UIOP (PWR)

PCI-E x8

PCI-X 133

ATA100

3 Gb /s

1-6

S

UPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer, B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Paciﬁ c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8228-1366, ext.132 or 139

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 6015B-UR/

6015B-U/6015B-NTR/6015B-NT up and running. Following these steps in the order

given should enable you to have the system operational within a minimum amount

of time. This quick setup assumes that your system has come to you with the

processors and memory preinstalled. If your system is not already fully integrated

with a serverboard, processors, system memory etc., please turn to the chapter or

section noted in each step for details on installing speciﬁ c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 6015B-UR/6015B-U/6015B-NTR/

6015B-NT was shipped in and note if it was damaged in any way. If the server itself

shows damage you should ﬁ le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the 6015B-UR/6015B-

U/6015B-NTR/6015B-NT. It should be situated in a clean, dust-free area that is well

ventilated. Avoid areas where heat, electrical noise and electromagnetic ﬁ elds are

generated. You will also need it placed near a grounded power outlet. Be sure to

read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6015B-UR/6015B-U/6015B-NTR/6015B-NT was shipped

in should include two sets of rail assemblies, two rail mounting brackets and the

mounting screws you will need to install the system into the rack. Follow the steps

in the order given to complete the installation process in a minimum amount of time.

Please read this section in its entirety before you begin the installation procedure

outlined in the sections that follow.

2-2

S

UPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack to allow for

sufﬁ cient airﬂ ow and ease in servicing.

- This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

- This product is not suitable for use with visual display work place devices according

to §2 of the the German Ordinance for Work with Visual Display Units.

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully extended to the

ﬂ oor with the full weight of the rack resting on them.

- In single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component from the

rack.

- You should extend only one component at a time - extending two or more simul-

taneously may cause the rack to become unstable.

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you install the

rails.

- Install the heaviest server components on the bottom of the rack ﬁ rst, and then

work up.

- Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a power

failure.

-

Allow the hot plug SATA drives and power supply modules to cool before touching

them.

-

Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

!

Warnings and Precautions!

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera-

ture of the rack environment may be greater than the ambient temperature of the

room. Therefore, consideration should be given to installing the equipment in an

environment compatible with the manufacturer’s maximum rated ambient tempera-

ture (Tmra).

Reduced Airﬂ ow

Equipment should be mounted into a rack so that the amount of airﬂ ow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply connec-

tions other than the direct connections to the branch circuit (i.e. the use of power

strips, etc.).

2-4

S

UPERSERVER 6015B-UR/6015B-U/6015B-NTR/6015B-NT User's Manual

2-4 Installing the System into a Rack

This section provides information on installing the 6015B-UR/6015B-U/6015B-NTR/

6015B-NT into a rack unit with the rack rails provided. If the system has already

been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There are

a variety of rack units on the market, which may mean the assembly procedure will

differ slightly. You should also refer to the installation instructions that came with

the rack unit you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies in the rack mounting kit. Each

assembly consists of two sections: an inner ﬁ xed chassis rail that secures directly

to the server chassis and an outer ﬁ xed rack rail that secures directly to the rack

itself (see Figure 2-1). Two pairs of short brackets to be used on the front side of

the outer rails are also included.

Installing the Inner Rails

Both the left and right side inner rails have been pre-attached to the chassis.

Proceed to the next step. A

Figure 2-1. Identifying the Sections of the Rack Rails

(right side rail shown)

Page is loading ...

Supero 6015B-NTR User manual

Related papers

Other documents