VENOM Atomik Barbwire XL 24in Brushless RC Boat Owner's manual

Brand: VENOM

Model: Atomik Barbwire XL 24in Brushless RC Boat

Category: Toys & accessories

Type: Owner's manual

www.

atomikrc

.com

18008

Atomik RC

14028 N. Ohio Street

Rathdrum, Idaho 83858 USA

www.atomikrc.com

www.facebook.com/AtomikRC www.twitter.com/Atomik_RCwww.pinterest.com/atomikrc www.youtube.com/theatomikrc

0-14

Customer Service

For Customer Service issues

and the quickest warranty service

please visit www.atomikrc.com.

READY-TO-RUN

INSTRUCTION

MANUAL

ATOMIKRC.COM

Included Items

Important Notes

Included Items Pg.1

Important Notes Pg.1

Important Warnings Pg.2

Charging Instructions Pg.2

Proper Connection & LED Indicators Pg.2

LiPO Battery Safety Guidelines Pg.2-3

New Battery Break-In Pg.3

Discharging Instructions Pg.4

Battery Installation Pg.4-5

Transmitter/Receiver Binding Pg.5

Basic Controls Pg.5

Pre-Run Checklist Pg.6

Driving Your Boat Pg.6

Transmitter Introduction Pg.6

EPA & Trim Adjustments Pg.7

Lubricating the Drive Shaft Pg.7

Troubleshooting Pg.8

Replacement Parts Pg.8

Warranty and Warnings Pg.9

Table of Contents

- Your Atomik Barbwire XL RC RTR Boat comes with a water-cooling system. Before using your

model, carefully check the silicone tubing to make sure the water-cooling system is working

correctly and that all tubes are properly attached and free of debris. If the system is not

correctly installed, this could lead to ESC burn out and motor defect.

The Atomik Barbwire XL is designed for use in fresh water only. They are not designed to be

used in salt water.

Boat

Boat Stand 40C 3S 2200mAh 11.1

Venom LiPO Battery

Allen Wrenches

2.5mm & 2.0mm

Receiver Balloon for Receiver

Spare Nylon

Propeller

Velcro

Strap

Transmitter

2-3 Cell LiPO

Balance Charger

ATOMIKRC.COM

18008

Important Warnings

LiPO Battery Safety Guidelines

Charging and discharging batteries has the potential for re, serious injury to persons and damage to

property. The user of this charger agrees to accept responsibility for all such risks. Atomik®, its aliates,

manufacturers, distributors, and retail partners cannot control the use, application, charging or installation

of this product and shall not be held responsible for any accident, injury to persons, or damage to property

resulting from the use of this product.

REFER TO THE LiPO SAFETY GUIDELINES IN THESE INSTRUCTIONS FOR MORE INFORMATION.

Always use a charger specically designed for LiPO batteries. ONLY charge 2 - 3 Cell LiPO Batteries with this

charger. Never use NiCD or NiMH type chargers to charge LiPO batteries. Failure to do so will damage the

batteries and may cause re and personal injury. Read all Safety Guidelines, Charging Instructions, New

Battery Break-In, and Battery Disposal Instructions before using batteries. Store battery packs out of the

reach of children and pets. Children under the age of 18 must be supervised by a responsible adult.

Always use a charger specically designed for Lithium Polymer batteries. Never use NiCD or NiMH type chargers

to charge LiPO batteries. Doing so will damage the batteries and may cause re and personal injury.

Always charge batteries in a re proof container or in the open, away from ammable materials. Do not charge

batteries on wood, cloth, carpet, in your model, or on any other ammable material. Keep a chemical re

extinguisher nearby in case of re.

Never leave batteries unattended while charging. Always observe batteries when charging so that you may react

quickly to any problems that may occur.

4. Venom LiPO cells feature a separate balancing plug that isolates each cell in a pack and charges it

independently. This ensures that all cells peak equally and discharge at the same rate during use,

preventing one or more cells from discharging past their safe low voltage cut o rating. The balancing plug

can be identied by the multi wire JST XH plug.

5. Charge each battery pack individually. Never charge battery packs in series. Charging packs in series may

result in improper charger cell recognition and an improper charging rate that may lead to overcharging,

cell damage and re.

6. Always check to make sure that your charger settings match those listed on the battery pack label. Refer to

the battery label for the proper cell count and charging amperage setting. Selecting a cell count or

amperage charge rate other than the one listed on the battery pack will damage the battery and may

cause a re.

7. Make sure the battery connections are connected in the correct polarity. Incorrect connections will

damage the battery/charger and may cause a re.

8. Always check battery pack voltage before charging. Do not discharge LiPO batteries below 3.0 Volts per

cell. The voltage of a typical LiPO cell at rest is 3.7 Volts. If the battery pack appears swollen or damaged,

DO NOT attempt to charge it. Check the voltage and follow the steps listed in the discharging instructions

section.

9. Do not charge at over 1C current. C= battery pack mah capacity ÷ 1000. Divide the battery mah

capacity by 1000 to determine the proper charge rate. Example: 1200mah ÷ 1000 = 1.20 Amps

Charge Rate for Venom Power LiPO Battery Packs, example:

a. 800mah Capacity

b. 1200mah Capacity

c. 2000mah Capacity

= 0.80 Amps

= 1.20 Amps

= 2.00 Amps

ATOMIKRC.COM

LiPO Battery Safety Guidelines Cont.

New Battery Break-In

10. Do not charge to more than 4.2 Volts per cell. Example: A 2S Battery Pack contains two

cells, therefore the voltage should not exceed 8.4 Volts.

11. Battery temperature is critical. For optimum performance in cold climates, warm the pack to

100Fº/ 37Cº before use. Please use the following guidelines:

a. Charge Temp Range:

b. Discharge Temp Range:

c. Storage Temp Range:

12. If the battery exceeds the temperature guidelines as above, isolate the battery pack and follow the

steps listed in the discharging instructions section.

1. New LiPO battery packs may require 12 or more charge/discharge cycles before the battery’s

optimum performance is reached.

2. During this time, it is recommended that the battery pack is not discharged over 7C.

7C = 7 x 1C, where 1C= battery pack mah capacity ÷ 1000.

Example: [(1250mah ÷ 1000) x 7] = 8.75 Amps

Recommended Maximum Discharge Rates During Break-In Period

a. 800mah Capacity

b. 1200mah Capacity

c. 2000mah Capacity

32 - 110Fº / 0-43Cº

32 - 140Fº / 0-60Cº

40 - 80Fº / 4-26Cº

= 5.4 Amps

= 8.4 Amps

= 14 Amps

Charging Instructions

Proper Connection & LED Indicators

1) Plug the power cord into the LiPO Balance Charger and then into an open wall outlet.

2) All three cell indicator LEDs will illuminate green indicating power is applied and is ready to charge.

3) Plug the LiPO battery into the correct charging port on the charger. The cell indicator LEDs will change

from Green to Red indicating that the battery is charging.

4) When charging is complete, the LEDs will change from Red to Green. Charge times will vary depending on

the capacity of the battery and if there is already a partial charge on the battery. Time estimates are based

on a battery discharged to 3.0V per cell.

5) If the battery gets warm or hot during charging, immediately disconnect the battery, set it on a

non-ammable surface and allow it to cool down. During the cool down period, monitor the pack for any

signs of swelling or “ballooning” indicating a damaged battery. If the battery is damaged, follow the

disposal instructions found in the “LiPO Battery Safety Guideline” section in this manual.

1) Power Plug

2) Charging LEDs

3) Battery Balance Ports

ATOMIKRC.COM

18008

Discharging Instructions

1. Never discharge a LiPO battery pack at more than the manufacturers recommended discharge rate.

The discharge rate is: Battery pack capacity (mah) ÷ 1000 x Pack C rating:

Example for 15c packs: (3200 mah ÷ 1000) x 15c = 48 Amps

Example for 20c packs: (2100 mah ÷ 1000) x 20c = 42 Amps

2. If the battery swells “balloons” or if the battery exceeds temperature guidelines, follow these safety steps:

a. Immediately remove the battery pack from your model or charger.

b. Place the battery in a non-ammable, well ventilated area.

c. Observe the battery for 30 minutes from a safe distance.

d. After 30 minutes, if the pack appears stable, is not swollen and does not show any signs of

damage, return the battery pack to normal use with caution.

3. If a battery is deformed, swollen or appears damaged, DO NOT CHARGE, DISCHARGE or

USE IN ANY WAY. Please contact Venom Customer Service for further instructions.

4. Do not let exposed battery wires touch each other. This may cause the battery to short and potentially

cause a re.

5. Store your batteries in a cool, dry place between 40-80 Fº / 4-26 Cº. LiPOs should be charged to 50% of

their capacity minimum before being stored.

Battery Installation

Installing the LiPO Battery in your Boat

(Always turn on the transmitter before connecting the

battery to the ESC.)

1. Remove the hatch by turning the hatch pull at the rear.

2. Insert the battery into the left side of the hull. Strap the

pack with the included strap inside the hull. When

installing the battery, make sure the wires point

towards the bow (front of the boat). Battery leads that

point towards the stern (back of the boat) may

become entangled with the outrunner motor causing

damage to the battery, motor, and could

possibly start a re.

3. Attach the battery connector to the matching connector inside the model. Listen for three continuous

beeps. (Signal noise of auto detection of the ESC.)

4. Replace the hatch. BE SURE THE HATCH IS SECURELY FASTENED TO THE BOAT!

5. Use two 2” - 3” strips of included hatch tape on both sides of the hatch.

NOTE: 1. There is a rubber ring placed along the slot of the hull. Always make sure it is secured properly

before re-positioning the hatch.

2. When you are not using the boat, remove the rubber ring from the hull. This will keep the rubber

ring exible and provide eective water-resistance for future use. Always remove the

LiPO battery when not in use!

Beep 3x’s

CHARGING OR DISCHARGING A DEFORMED, SWOLLEN OR DAMAGED BATTERY

WILL INCREASE THE RISK OF FIRE AND/OR PERSONAL INJURY.

WARNING:

ATOMIKRC.COM

Battery Installation Cont.

Installing the AA Batteries in your Transmitter

1. Make sure the transmitter ON/OFF switch is in the “OFF”

position.

2. Remove battery cover by pressing down on the

embossed arrow and sliding the cover as indicated.

3. Insert 4 AA batterries, playing close attention to the + and

- polarity.

4. Slide the battery cover back into place.

NOTE: Remove all AA batterries from the transmitter if you

do not intend to use it for an extended period of time.

Transmitter/Receiver Binding

The binding process ties the transmitter and receiver together. Under normal circumstances, this will be

done at the factory. If, however, you nd that your transmitter and boat are not communicating (receiver’s

red LED light is on), please follow these instructions:

1. Switch “ON” the transmitter.

2. Switch “ON” the receiver by attaching the 11.1V LiPO battery pack’s connector to the matching connector

in the boat.

3. Press down the “BIND” button on the receiver. The receiver’s green LED light will be on to indicate that

binding has been successful and the receiver will now accept commands from the transmitter.

NOTE 1: During the binding process, the transmitter and receiver should be no more than 3ft. apart and no

other similar devices should be within 35ft.

NOTE 2: If the green LED light is ashing, the binding process has failed. Please repeat the steps above.

Basic Controls

1. Forward Throttle Trigger

Your Atomik Barbwire can be driven forward by pulling the

throttle trigger. Release the trigger to stop the boat.

2. Left/Right Steering Wheel

The steering wheel controls the model’s left and right

movement. Turn the wheel to the left to steer to the left. Turn

the wheel right to steer the boat right. Release the wheel to

go straight.

RACING TIP: This model is an oval racer designed for clockwise

racing and will be less responsive to steering inputs at high

speed, particularly left turns. Decrease your speed to allow

tighter turning.

ATOMIKRC.COM

18008

Pre Run Checklist

Driving Your Boat

1. Switch “ON” the transmitter. Check that the transmitter’s red LED light glows brightly.

2. Switch “ON” the model. (Connect the LiPO battery pack.)

3. Check that the propeller and rudder respond to the transmitter inputs before placing the boat in the water.

After Use:

1. When you have nished using the boat, rst switch “OFF” the model by disconnecting the battery pack. Then

switch “OFF” the transmitter.

2. Remove all batteries from the transmitter and model.

3. Leave the boat’s upper deck o to allow moisture to evaporate. Place the model in a safe, dry place until it is

dry and then store it away.

NOTE: If the boat begins to operate sluggishly when running, it may have taken on an excessive amount of water.

In this case, you should immediately return to shore, remove the upper deck and drain the water

from the hull.

If the boat does not run in a straight line when not being steered, you

can x this by adjusting the steering trim located on the upper right

hand side of the transmitter.

1. Run your model on calm water when adjusting the steering. If your

model runs to the right when not being steered, press the “ST. TRIM-L”

button. Re-center the model and see if this has corrected the

problem. Keep making small adjustments in this way until the model

runs straight.

2. Press the “ST. TRIM-R” button to correct if the model steers to the left

without being steered in the same way as explained above.

Transmitter Introduction

REV

POWER

NOR

Steering Switch Reverse

Throttle Trim Brake

Throttle Trim Forward

Power Indicator

Steering Switch Normal

Steering Trim Right

Steering Trim Left

Steering Travel Angle Left

Steering Travel Angle Right

Always use Atomik RC Hatch Tape

(part# 0864) to secure the hatch.

Racing Tip:

Inspect all running hardware. Look for loose screws and nuts. Make sure all screws on the motor

and ex shaft coupler are snug. Tighten the ex shaft coupler using (2) 10mm wrenches (not

included). Do not over tighten.

Inspect the cooling lines for any cracks, clogging, or wear.

Install battery making sure they are charged and secure.

Perform a radio test by range checking your transmitter.

100 feet recommended.

Be very certain the hatch is 100% secure.

ATOMIKRC.COM

Lubricating the Drive Shaft

End Point Adjustment

Trim Adjustments

IMPORTANT:

The bearing in the water cooled motor mount must be regularly lubricated with oil, grease or

Vaseline® petroleum jelly to prevent corrosion through the ingress of water. Insucient

lubrication may lead to the premature failure of the bearing. Note: Image shows drive shaft

removed for clarity - the bearing can be lubricated with the drive shaft in place.

REV

POWER

NOR

REV

POWER

NOR

Functions

Use this when performing left and right steering angle adjustments, throttle high

side/brake side operation amount adjustment during linkage. End Point

Adjustment (EPA) adjusting value range: 0% - 100%.

Settings

1. Steering (right side) adjustment

Rotate “ST/R” knob to the left end points means minimum value 0%, right end

point means maximum value 100%.

2. Steering (left side) adjustment

Rotate “ST/L” knob to the left endpoint means minimum value 0%, right end

point means maximum value 100%.

CAUTION:

When adjusting this function, make sure the direction is in agreement

with the boat direction, you can adjust by the “REV - NOR” button.

Steering trim, adjust “ST/TRIM” “R/L” so that rudder is centered prior to operation,

you may adjust this control to make the boat run straight during operation.

Throttle trim, adjust “TH/TRIM” “B/F” to stop propeller from turning while the

throttle trigger is in the neutral position.

CAUTION:

When adjusting this function, make sure the direction is in agreement with the

boat direction, you can adjust by the “REV - NOR” button.

Using (2) 10mm wrenches (not included) loosen the ex shaft coupler

and slide the ex shaft w/prop shaft out of the stung tube.

Lubricate the ex shaft w/prop shaft with waterproof marine grease.

Reinstall the ex shaft w/ prop shaft in reverse order, be sure to

retighten the ex shaft coupler.

ATOMIKRC.COM

18008

Troubleshooting

Replacement Parts

Model will not move No battery in transmitter/model

Battery installation is incorrect

Weak battery in transmitter

Weak battery in model

Install batteries

Install batteries correctly

Install a fresh battery

Recharge the LiPO battery

No control of model Weak battery in transmitter Install a fresh battery

Install a fresh battery

Weak battery in transmitter

Limited radio range

18110

Hatch - Barbwire XL

18112

Water-Cooled Motor

Mount - Barbwire XL

18111

Outrunner Brushless

Motor - Barbwire XL

18113

30A Water-Cooled

Brushless ESC -

Barbwire XL

18114

Flex Shaft Set -

Barbwire XL

18116

Strut Set -

Barbwire XL

18115

Rudder and Support

Set - Barbwire XL

18117

Waterproof Rubber

Rings - Barbwire XL

ATOMIKRC.COM

Warranty & Warnings

Keep the packaging and instruction manual as they contain important information.

Always check your model for loose screws and components before operating.

Always unplug the battery in the model before removing debris that has become tangled in the prop.

The transmitter's range will vary depending on your surroundings and battery strength. Do not operate too far away or control will be lost.

Ensure that all batteries are correctly installed and that the 6V NiMH battery is fully charged.

Do not touch moving parts during operation, especially the propeller.

Some of the electronic components may become very hot during use and can severely burn you if touched before they cool. Let the model stand and cool

down before handling the motor, ESC and cooling components.

If you lose control of your model, never wade into the water with strong currents to retrieve it. First, hold the transmitter as high as you can and try to

re-establish control. If this does not work, nd another way to move closer to the model, but do not endanger yourself in the process.

GENERAL WARRANTY POLICIES

Atomik® warrants this product to be free of material and workmanship defects when new. Atomik® will at its sole discretion repair or replace defective

components free of charge within 90 days from date of purchase or within 30 days for all electronic components. This warranty does not cover wear and

tear, crash damage, modications, failure to perform routine maintenance, or any damages arising as a result of improper use. All warranty claims are to be

directed to Atomik® Customer Service at: www.atomik rc.com

GUARANTEE

All products are inspected and adjusted individually before leaving the manufacturer and are guaranteed to be free of material defects and

manufacturing faults.

IMPORTANT NOTICE

Atomik® assumes sole responsibility for our products; therefore, dealers should not be involved in any warranty issues. All warranty claims are to be

directed to Atomik® Customer Service. Before returning any defective product, please contact Atomik® Customer Service at 800-705-0620 (208-762-0620)

to receive a Return Merchandise Authorization Number. A dated & itemized sales receipt must accompany any product returned for warranty work.

RELEASE OF LIABILITY

Atomik®, It’s aliates, manufacturers, distributors, or retail partners shall not be held liable for any accident, injury to persons, or damage to property

resulting from use, misuse, or abuse of any Atomik® product. In purchasing a Atomik® product the user agrees to accept responsibility for all such risks.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Charging and discharging batteries has the potential for serious injury to persons and damage to property. In purchasing this product, the user agrees to

accept responsibility for all such risks, and will not hold Atomik®, it’s aliates, manufacturers, distributors, or retail partners responsible for any accident,

injury to persons, or damage to property resulting from the use of this product.

Adult supervision is required when using this product. This product should be assembled by an adult before use. Proper assembly should be checked by

an adult before use. This product should be periodically examined by an adult for potential hazards. Any potential hazardous parts should be repaired or

replaced.

WARNING: This product contains sharp edges or objects that can cause cuts or other bodily injury. To prevent cuts or other bodily injury, do not contact

sharp edges or objects.

FCC WARNING:

FCC ID: ZDTJ3C0001

CAUTION: Atomik® is not responsible for any radio or TV interference caused by unauthorized modications to this product. Changes or modications

not authorized by Atomik® will void all warranties.

NOTE: This product has been tested and found to comply with the limits for a Class B digital device, compliant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio

frequency energy and, if not installed and used as instructed, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be

determined by turning the product on and o, correct the interference by trying one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from the receiver.

- Consult the dealer or an experienced radio/TV technician for help.

This product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Be responsible, dispose of

properly.

NOTICE OF RIGHTS

or otherwise, without the prior written permission of Atomik®. For information on getting permission for reprints and excerpts, contact Atomik® Customer

Service.

NOTICE OF LIABILITY

The information in this manual is distributed on an “As Is” basis, without warranty. While every precaution has been taken in the preparation of the manual,

Atomik® does not have any liability to any person or entity with respect to any loss or damage caused or alleged to be caused directly or indirectly by the

information contained in this manual or by the products described in it.

Actual product may vary from product shown. Product is subject to change.