PERATOR'S MAN AL

®

1/2 in. 19.2 VOLT CORDLESS DRILL-DRIVER

VARIABLE SPEED/REVERSIBLE

Model Nos.

315.114852

315.114853

A

WARNING: To reduce the risk of injury,

983000-848

12123-08 (REV:07)

Save this manual for future reference

[] Warranty .......................................................................................................................................................................... 2

[] Introduction ..................................................................................................................................................................... 2

[] General Safety Rules .................................................................................................................................................... 3-4

[] Specific Safety Rules....................................................................................................................................................... 4

[] Safety Rules for Charger ................................................................................................................................................. 5

[] Symbols ........................................................................................................................................................................ 6-7

[] Features ........................................................................................................................................................................ 8-9

If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN iT TO ANY

SEARS STORE OR PARTS AND REPAIR CENTER OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR

FREE REPAIR (or rep(acement if repair proves impossib(e).

If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of

purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, iL 60179

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

A

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities

to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust

masks that are specially designed to filter out microscopic particles.

_ WARNING!READANDUNDERSTAND ALL

INSTRUCTIONS. Failure to follow all instructions

listed below may result in electric shock, fire and/or

serious personal injury.

SAVE THESE iNSTRUCTiONS

WORK AREA

[] Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

[] Do not operate power tools in explosive atmo-

ELECTRICALSAFETY

[] A battery operated tool with integral batteries or a

separate battery pack must be recharged only with

the specified charger for the battery. A charger that

may be suitable for one type of battery may create a

risk of fire when used with another battery.

[] Use battery operated tool only with specifically des-

ignated battery pack. Use of any other batteries may

create a risk of fire.

[] Use battery only with charger listed.

MODEL BATTERY PACK CHARGER

(NFCd)

PERSONAL SAFETY

(Multi-Chemistry)

[] Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use tool while tired or under the influence of

drugs, alcohol, or medication. A moment of inatten-

tion while operating power tools may result in serious

personal injury.

[] Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep your hair, clothing,

and gloves away from moving parts. Loose clothes,

[] Remove adjusting keys or wrenches before turning

the tool on. A wrench or a key that is left attached to a

rotating part of the tool may result in personal injury.

[] Do not overreach. Keep proper footing and balance

at all times. Proper footing and balance enable better

[] Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes, hard hat, or hearing

protection must be used for appropriate conditions.

hair. Loose clothes, jewelry, or long hair can be drawn

into air vents.

the work by hand or against your body is unstable and

may lead to loss of control.

[] Do not force tool. Use the correct tool for your

application. The correct tool will do the job better

and safer at the rate for which it isdesigned.

[] Do not use tool if switch does not turn it on or off.

A tool that cannot be controlled with the switch is dan-

gerous and must be repaired.

[] Disconnect battery pack from tool or place the

any adjustments, changing accessories, or storing

the tool. Such preventive safety measures reduce the

nails, screws, or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

sparks, burns, or a fire.

[] Maintain tools with care. Keep cutting tools sharp

and clean. Properly maintained tools with sharp cut-

ting edges are less likely to bind and are easier to

control.

[] Check for misalignment or binding of moving parts,

breakage of parts, and any other condition that

[] Use only accessories that are recommended by the SERVICE

used on another tool.

and deterioration of the enclosure plastic.

section of this manual. Use of unauthorized parts or

rule will reduce the risk of serious personal injury.

electrical outlet; therefore, they are always in

[] Batteries can explode in the presence of a source

of ignition, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product

in the presence of open flame. An exploded battery

[] If the power supply cord is damaged, it must be

[] Use of an attachment not recommended or sold

fire, or serious personal injury.

[] Do not abuse cord or charger. Never use the cord to

carry the charger. Do not pull the charger cord rather

immediately.

plastic.

NOTE: AWG = American Wire Gauge

[] Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any

way. Take it to an authorized serviceman for electrical

check to determine if the charger is in good working

order.

[] Do not disassemble charger. Take it to an authorized

serviceman when service or repair is required. Incorrect

reassembly may result in a risk of electric shock or fire.

[] Risk of electric shock. Do not touch uninsulated

portion of output connector or uninsulated battery

terminal.

CAUTION: To reduce the risk of injury, charge only nickel-cadmium rechargeable batteries. Other types of batteries

may burst, causing personal injury or damage.

Someofthefollowingsymbolsmaybeusedonthisproduct.Pleasestudythemandlearntheirmeaning.Proper

interpretationofthesesymbolswillallowyoutooperatetheproductbetterandsafer.

SYMBOL NAME DESIGNATION/EXPLANATION

A

mz

W

min

n o

@

Hertz

Minutes

Direct Current

No Load Speed

Class II Construction

Wet Conditions Alert

No Hands Symbol

No Hands Symbol

Hot Surface

Thefollowingsignalwordsandmeaningsareintendedtoexplainthelevelsofriskassociatedwiththisproduct.

SYMBOL SIGNAL MEANING

SERVICE

cian. For service we suggest you return the product to

Gear Train .............................................................. 2 Speed

KEYLESS

REARViEW

SWITCH

DiRECTiONOF

CENTERLOCK)

PACK

4-1/2 in.

Before use of this product, familiarize yourself with all op-

erating features and safety rules.

BIT STORAGE

Bits provided with the drill can be placed in the storage

area, located on the base of the drill

The charger has a key-hole hanging feature for conve-

so that the center distance is 4-1/2 in.

(FORWARD/REVERSE/CENTER LOCK}

Your drill has a direction of rotation (forward/reverse/cen-

ter lock) selector located above the switch trigger for

changing the direction of bit rotation. Setting the switch

trigger in the OFF (center lock) position helps reduce the

possibility of accidental starting when not in use.

See Figures 11 - 12..

housing to help keep the drill bit level during use.

[] Check the direction of rotation selector for the correct

setting (forward or reverse).

clamps to keep it from turning as the drill bit rotates.

drilled.

[] Depress the switch trigger to start the drill.

[] Move the drill bit into the workpiece, applying only

A

[] When drilling metals, use a light oil on the drill bit to

keep it from overheating. The oil will prolong the life of

brake is functioning properly, sparks will be visible through

the vent slots on the housing. This is normal and is the

action of the brake.

[] Begin drilling at a very low speed to prevent the bit

behind the workpiece to prevent ragged or splintered

16

slipping off the starting point.

• Wear the bearings;

• Produce off-center or irregular-shaped holes.

A

glasses with side shields when using compressed air

to clean products. If the operation is dusty, also wear

remove the battery pack from the product when

This product will accept DieHard<_19.2 V lithium-ion bat-

maximum trouble-free life. However, like all batteries, they will

eventually wear out. Do not disassemble battery pack and

especially when wearing rings and jewelry, could result in a

To obtain the longest possible battery life, we suggest the

For lithium=ion batteries:

== Remove the battery pack from the charger once it is

fully charged and ready for use.

For battery pack storage longer than 30 days:

== Store the battery pack where the temperature is below

• Store battery packs in a 30%-50% charged condition.

• Every six months of storage, charge the pack as normal.

For nickel=cadmium batteries:

• Remove the battery pack from the charger once it is

fully charged and ready for use.

For battery pack storage longer than 30 days:

80°R

• Store battery packs in a "discharged" condition.

17

[] Lock the switch trigger by placing the direction of rota-

tion selector in center position.

[] Insert a 5/16 in. or larger hex key intothe chuck of the

drill and tighten the chuck jaws securely.

[] Tap the hex key sharply with a mallet in a clockwise di-

MALLET

HEXKEY CHUCK

Open the chuck jaws and remove the hex key. Using a

screwdriver, remove the chuck screw by turning it in a

HEXKEY

[] Open the chuck jaws.

[] Insert the hex key into the chuck and tighten the chuck

jaws securely. Tap the hex key sharply with a mallet in

a clockwise direction. This will tighten the chuck on the

spindle.

[] Open the chuck jaws and remove the hex key.

[] Tighten the chuck screw.

SCREWDRIVER

Fig. 14

Insert the hex key into the chuck and tighten the chuck

clockwise direction. This will loosen the chuck on the

18

4

Key Part

1 6613402

2 6903323

4 1425301

11 900211023

Chuck ............................................................................................................ 1

*Charger (Item No. 9_11041) ............................................................................. 1

Data Plate (114852) (Not shown) ..................................................................... 1

Logo Plate (114852) (Not shown) .................................................................... 1

Data Plate (114853) (Not shown) ..................................................................... 1

Carrying Case (11548 Combo) (Not shown) .................................................... 1

Bag (11588 Combo) (Not shown) .................................................................... 1

Operator's Manual

For repair of carry-in items like vacuums, lawn equipment,

www.sears.com

www.sears.ca

Para pedir servicio de reparaci6n

Au Canada pour service en fran£ais:

1-800-LE-FOYER M°

TM

® Marca Registrada / Marca de Fabrica / SMMarca de Servicio de Sears Brands, LLC

MCMarque de commerce / Marque depos6e de Sears Brands, LLC © Sears Brands, LLC