Edelbrock 14851485 Operating instructions

Brand: Edelbrock

Model: 14851485

Type: Operating instructions

Edelbrock 14851485 is a Carburetor Calibration Kit designed to optimize the calibration of Edelbrock Marine Carburetor #1409 when combined with Performer intake manifold #2111 on Marine 4.3L V6 engines. This kit includes two Primary Metering Jets, two Secondary Metering Jets, two Metering Rods, and two Step-up Springs. It allows you to fine-tune your carburetor for maximum performance and efficiency. With this kit, you can easily adjust the fuel-air mixture and improve the overall performance of your engine.

Edelbrock 14851485 is a Carburetor Calibration Kit designed to optimize the calibration of Edelbrock Marine Carburetor #1409 when combined with Performer intake manifold #2111 on Marine 4.3L V6 engines. This kit includes two Primary Metering Jets, two Secondary Metering Jets, two Metering Rods, and two Step-up Springs. It allows you to fine-tune your carburetor for maximum performance and efficiency. With this kit, you can easily adjust the fuel-air mixture and improve the overall performance of your engine.

Carburetor Calibration Kit #1485

for Edelbrock Performer Series Carburetor

#1409 when used with Performer manifold

#2111 on Marine 4.3L V6 engines

• Please study these instructions carefully before

installing your new calibration kit. If you have any

questions or problems, do not hesitate to contact our

Technical Hotline at: 1-800-416-8628.

• Applications: This calibration kit was developed to

optimize the calibration of Edelbrock Marine

Carburetor #1409 when combined with Performer

intake manifold #2111 on Marine 4.3L V6 engines.

This kit is intended to be used only with this combi-

nation of parts. For other applications, see your car-

buretor's Owner's Manual for calibration suggestions.

• Installation Instructions

1. Using a 1/4" nut driver, loosen the Step-up Piston

Cover Screws (1) and pivot the Step-up Piston Cover

Plates (2) to the side. The Metering Rods (3) and

Step-up Springs (4) can now be removed.

2. Disconnect the Choke Cam Connector Rod (5),

Pump Connector Rod (6), and Choke Connector

Rod (7).

3. Remove the nine Airhorn Attaching Screws and

remove the Airhorn from the carburetor body. Be

careful not to set the lid down on the floats.

4. A standard screwdriver can now be used to remove

the old Metering Jets and install the new .089"

Metering Jets. Both pairs of Primary (8) and

Secondary Metering Jets (9) should be replaced with

the new Metering Jets; all four Metering Jets sup-

plied in this kit are the same and may be used in

either Primary or Secondary locations. Once the

desired Metering Jets have been installed the carbu-

retor may be reassembled by reversing the above pro-

cedure. Be sure to replace the Step-up Piston

Springs and Metering Rods with the new parts sup-

plied (Pink colored Step-up Springs and .068" x

.057" Metering Rods).

• Kit Contents

2) Primary Metering Jets (.089")

2) Secondary Metering Jets (.089")

2) Metering Rods (.068" x .057")

2) Step-up Springs (pink; 7")

1) Installation Instructions

2

4

3

7

6

5

3

9

8

1

© 1998 Edelbrock Corp. 6/98

1

Edelbrock 14851485 Operating instructions

Brand: Edelbrock

Model: 14851485

Type: Operating instructions

Edelbrock 14851485 is a Carburetor Calibration Kit designed to optimize the calibration of Edelbrock Marine Carburetor #1409 when combined with Performer intake manifold #2111 on Marine 4.3L V6 engines. This kit includes two Primary Metering Jets, two Secondary Metering Jets, two Metering Rods, and two Step-up Springs. It allows you to fine-tune your carburetor for maximum performance and efficiency. With this kit, you can easily adjust the fuel-air mixture and improve the overall performance of your engine.

Related papers

Other documents