Phobya Touch 6 Installating And Operation Manual

Brand
Phobya
Model
Touch 6
Type
Installating And Operation Manual

Below you will find brief information for Touch 6 Single Bay 5,25". This user manual provides instructions for installing and operating the Phobya Touch 6 fan controller. The device fits into a 5.25" drive bay and features six channels to control fan speeds and monitor temperature. It has a power button, a light bulb button to adjust brightness, and fan buttons for each of the six channels. The device supports a voltage range from 5V to 12V DC and up to 30 watts per channel. It includes an alarm function that is triggered when the temperature reaches 70 degrees Celsius.

Below you will find brief information for Touch 6 Single Bay 5,25". This user manual provides instructions for installing and operating the Phobya Touch 6 fan controller. The device fits into a 5.25" drive bay and features six channels to control fan speeds and monitor temperature. It has a power button, a light bulb button to adjust brightness, and fan buttons for each of the six channels. The device supports a voltage range from 5V to 12V DC and up to 30 watts per channel. It includes an alarm function that is triggered when the temperature reaches 70 degrees Celsius.

Tools required: Phillips head screwdriver
Mount the product into a 5.25 inch drive bay of your computer
chassis using the screws in the accessory bag.
Connect the fans
Connect the
power supply
the mini jumper
Connect the temperature sensors
Use the mini jumper to
activate the alarm function
NOTE:
In order to protect your computer the device has the alarm function.
If the temperature exceeds 70 degrees Celsius, the unit will be
emitting noise. If the fans are not operating when the
voltage is over 6.5v, the unit will be emitting noise. Insert
the mini jumper to enable alarm function or remove it to
disable the alarm function
OPERATION:
Power button: The power button could turn or shut the back
light of the device
THE MAIN INTERFACE
The light bulb button: The light bulb button adjust the brightness
of the screen. There are three settings for the brightness. (If the
light bulb button is not being used, it will disappear in 6 seconds)
The fan 1 button: Touch it to enter the fan 1 branch interface
The fan 2 button: Touch it to enter the fan 2 branch interface
The fan 3 button: Touch it to enter the fan 3 branch interface
The fan 4 button: Touch it to enter the fan 4 branch interface
The fan 5 button: Touch it to enter the fan 5 branch interface
The fan 6 button: Touch it to enter the fan 6 branch interface
1
2
3
4
5
6
7
1 X Installation Guide 1 X Power Cable
6 X Fan Cable 6 X Sensors Cable
4 X Screws 1 X Jumper
6x Sticker for temperature
sensors
1. Connect the fans
Fan1: Connect the first channel fan
Fan2: Connect the second channel fan
Fan3: Connect the third channel fan
Fan4: Connect the fourth channel fan
Fan5: Connect the fifth channel fan
Fan6: Connect the sixth channel fan
P: Connect the power supply
2. Connect the temperature sensors
T1: Connect the first channel temperature sensor
T2: Connect the second channel temperature sensor
T3: Connect the third channel temperature sensor
T4: Connect the fourth channel temperature sensor
T5: Connect the fifth channel temperature sensor
T6: Connect the sixth channel temperature sensor
ALARM: Use the mini jumper to activate the alarm function
148.5mm x 42mm x 79.9mm (5.25” Bay)
112.5mm x 22.2mm
Up to 30 watts per channel
6 Channels
Black Anodized/Silver
+ 12V (Standard 4- Pin Connector)
5V- 12V DC / (40% - 100%)
Six 4 pin connectors
THE FAN BRANCH INTERFACE
For example, you touch the fan 2 button; you will enter the fan 2 branch
interface
The RPM and Voltage readout: Select the RPM or Voltage for
readout by touch.
The temperature readout: Select Celsius or Fahrenheit for readout
by touch.
The left arrow button area: Alternate to the previous branch interface.
NOTE: If the present interface is fan 1 then it will go to the fan 6 interface.
The power output rate line bar: Touch the end tips to adjust by increments of 5%.
The right arrow button: Alternate to the next branch interface.
NOTE: If the present interface is fan 6 then it will go to the fan 1
interface.
The back button: Back to the main interface.
1
2
3
4
5
6
  • Page 1 1
  • Page 2 2

Phobya Touch 6 Installating And Operation Manual

Brand
Phobya
Model
Touch 6
Type
Installating And Operation Manual

Below you will find brief information for Touch 6 Single Bay 5,25". This user manual provides instructions for installing and operating the Phobya Touch 6 fan controller. The device fits into a 5.25" drive bay and features six channels to control fan speeds and monitor temperature. It has a power button, a light bulb button to adjust brightness, and fan buttons for each of the six channels. The device supports a voltage range from 5V to 12V DC and up to 30 watts per channel. It includes an alarm function that is triggered when the temperature reaches 70 degrees Celsius.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents