Young One YP-G1T Owner's manual

Brand: Young One

Model: YP-G1T

Type: Owner's manual

BEFORE CALLING FOR SERVICE

Before calling for service, please check the trouble shooting chart below.

It includes several common faults which you can correct, making a service call

unnecessary.

OWNER’S MANUAL

Please read this owner’s manual thoroughly before operating

and keep it handy for reference at all times.

Point- Of-Use

Water Cooler

Model No. : YP-G10 (Hot & Cold Water)

YP-G1T (Hot & Cold Water)

YOUNG ONE Corporation

7.12.Z1 The specific instructions related to the safe operation of this

appliance (as given in 7.12 of this standard) shall be collated together

in the front section of the user instructions. The height of the characters,

measured on the capital letters, shall be at least 3 mm.

These instructions shall also be available in an alternative format, e.g. on

a website.

Check if the machine is placed close to a heat source

or direct sunlight.

Check if the machine is placed too close to a wall.

Machine must be more than 4 inches from the wall.

Check turn hot water switch on at the rear side.

Check if plugged in.

Check voltage. (It may be too high or low)

Cooler does not

operate.

Cooling efficiency

is low.

Heating efficiency

is low.

Is the machine placed on uneven floor?

Put the machine on firm and even surface.

ls there an obstacle at the back of the machine?

Remove the obstacle.

Abnormal noise

Drinking water does

not flow well. Check if the water valve is on “open” position.

CIRCUMSTANCE POSSIBLE CAUSE AND REMEDY

SAFETY INSTRUCTIONS

INSTALLATION

Use the machine for its intended

purpose only as described in this

manual.

Do not put any objects on the machine.

Unplug the machine before cleaning or

replacing parts of it.

Do not locate the machine direct

sunlight.

Do not locate the machine near the

radiator.

Do not locate the machine within or

directly adjacent to toilet facilities.

Do not locate the machine in constantly

damp areas,beneath dripping pipes,

or where water may collect underfoot.

Do not install the machine in a humid or

wet area.

All servicing should be performed by

qualified personnel only.

Do not use multiple socket outlet to

supply power.

If the power cord is damaged, it must

be replaced by the manufacturer or

by its service agent or a similar

qualified person in order to avoid injury

or hazard.

Place the machine on firm and even

surface. Unbalanced installation may

cause noise or vibrations.

Put the machine in an open area and

at a distance of more than 4 inches from

the wall. Otherwise, the cooling efficiency

may decrease.

The machine should be installed

within 6 feet from the nearest power

outlet.

The machine must be attached to a

portable water source.

The tubing job(usually 1/4”) which

connects the machine to the water supply

should not be exceed in 20 meters (65 feet).

Use only grounded outlet wall sockets.

The

machine

should be positioned in

such a way that the plug is easily

accessible.

CAUTION

1. Do not tilt appliance more than

45 degrees when moving system. 2. To avoid a hazard due to instability

of the appliance, it must be fixed in

accordance with the instructions.

Have 100mm space between the wall and the appliance

and install above the floow where

it is solid and flat.

(After transporting, don’t switch on the

power supply for approximately 1 hour)

1. This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible

for their safety.

Children should be supervised to ensure that they do not play with

the appliance.

2. This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision.

3. For appliances with type Y attachment, the instructions shall contain

the substance of the following.

If the supply cord is damaged, if must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

4. WARNING : To avoid a hazard due to instability of the appliance, it

must be fixed in accordance with the instructions.

PARTS IDENTIFICATION

INSTALLATION

HOW TO USE THE HOT WATER

Push the faucet lever for the hot water and press the lock button.

HOW TO USE THE COLD WATER

Push the faucet lever for cold water and push the continuous supply lever to the right.

Cold water lever

Push this lever.

For child lock

button

Lamp for hot

Lamp for cold

Rear Panel

Hot water Switch

Compressor base

1. Connect water tube (”A” side) to water inlet.

(water tube linked to the water valve) (POU Only)

2. Connect water tube (”B” side) to city water line.

Open the water valve after connecting the water tube

(”B” side) to the city water line. (POU Only)

3. Plug in.

4. Check hot water, cold water respectively.

Caution ! Turn the hot water switch on after checking

the hot water flow.

Notes :

1. If the water line pressure exceeds 65PSI,

a pressure regulator must be used.

Refer to user’s manual supplied with each

machine

for operation and care.

Hot

(or Room Temperature)

Water lever

Push this lever.

Tray drip

To gather the

overowing water.

Switch (Rear side)

To turn on (”I” position)

for hot water or

turn o(“O” position)

for room temp. water.

Temp. controller (Rear side

)

To control the temperature

of cooling water.

SPECIFICATIONS

YP-G10 YP-G1T

(220-240)V~ / 50Hz

0.5A

420W

Total

R-134a (32g)

330 W

287x357x970 270x452x515

1.85 ℓ2.3 ℓ

Water Valve

Water Tube

“A” Side

“B” Side

Filter out

Filter in

Water inlet

4 5

SAFETY INSTRUCTIONS CARE AND MAINTENANCE

SAFETY NOTICE

CLEANING

EXTERIOR

INTERIOR

LONG-TERM CARE

WATER LEVER

OPERATION PROCEDURE

CLEAN

The water faucet becomes easily dirty by

constant use. Clean it thoroughly at least

once in 3 months (figure 5).

Unplug the cooler before cleaning.

Clean the cooler regularly to ensure its

maximum efficiency.

Clean the water tank with vinegar if you

do not use the cooler for several days.

Clean the cooler every two months,

unless it includes in-tank sanitization

system. Do not use abrasive cleaning

tools nor sharp tools which may cause

defects or damages on the system.

(figure 4)

For extended vacation or absence, turn off

the power and clean the cooler inside and

out thoroughly.

Do not clean any part of the cooler with

gasoline, kerosene, thinner, etc.

Use clean cloth and mild detergent

when cleaning. Dry the surface with

clean and soft cloth. (figure 3)

Connect the water tube to water

inlet at the rear side and then

open the water valve on position.

1. WATER SUPPLY

2. Plug in.

Check flow of hot water, turn hot

water switch on at the rear side.

4. Check flow of cold water, hot water.

Note:

1. If hot water is connected to machine

as water source, it may damage the

machine. (figure 1)

1. Keep unplugged when the machine is

not in use for long period. (figure 2)

2. Do NOT put hands in the water tank

while in use.

3. Wait at least 4 minutes before restarting

the machine after unplugged.

STOP

Note:

1. Be careful, when hot water is flowing.

Otherwise you may injure yourself.

HOT WATER

Young One YP-G1T Owner's manual

Brand: Young One

Model: YP-G1T

Type: Owner's manual

Download PDF

report

Young One YP-G1T Owner's manual

Young One YP-G1T Owner's manual

Other documents