Hytronik IP65 High Bay HF Sensor HMW30 User manual

Hytronik
Brand
Hytronik
Model
IP65 High Bay HF Sensor HMW30
Category
Motion detectors
Type
User manual

This manual is also suitable for

Hytronik IP65 High Bay HF Sensor HMW30

The Hytronik IP65 High Bay HF Sensor HMW30 is a high-quality motion sensor designed for use in demanding environments. With its IP65 rating, it is dust-tight and protected against water jets, making it ideal for use in outdoor or harsh industrial settings.

The HMW30 uses advanced high-frequency (HF) technology to detect movement, providing a wide detection range of up to 20 meters in diameter when mounted on a ceiling at a height of 20 meters. It has a built-in daylight sensor that prevents the light from switching on when there is sufficient natural light, saving energy.

Hytronik IP65 High Bay HF Sensor HMW30

The Hytronik IP65 High Bay HF Sensor HMW30 is a high-quality motion sensor designed for use in demanding environments. With its IP65 rating, it is dust-tight and protected against water jets, making it ideal for use in outdoor or harsh industrial settings.

The HMW30 uses advanced high-frequency (HF) technology to detect movement, providing a wide detection range of up to 20 meters in diameter when mounted on a ceiling at a height of 20 meters. It has a built-in daylight sensor that prevents the light from switching on when there is sufficient natural light, saving energy.

2. Installation 1. Technical Specifications
Product type On/off control microwave motion sensor
Operating voltage 220~240VAC 50/60Hz
Capacitive: 800VA
Resistive: 1000W
Power consumption < 0.5W
Detection angle 360o
Detection area (Max.)*
Detection range 10% / 50% / 75% / 100%
Hold time 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min
Daylight threshold 2 ~ 500Lux, Disable
Warmming up time 20s
Operating temperature -20oC ~ +50oC
IP rating IP65
3. Rotary Switch Settings
A rotary switch is built inside the sensor for
scene selection / fast programming. Total of
16 channels available:
Note: settings can also be changed by remote control HRC-11. The last action controls.
HIGH BAY MICROWAVE MOTION SENSOR HMW30
Installation and Instruction Manual
Rotary switch preset (Please
see the location in 2. Installation)
Warnings:
1. Installation of the sensor involves connecting it to the mains supply. This work must be
carried out by a specialist in accordance with electrotechnical regulations.
2. Disconnect power supply before installing.
Detection
range
Channel
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
75%
50%
100%
100%
100%
5s
1min
5min
5min
5min
5min
5min
10min
10min
10min
10min
10min
10min
30min
30min
5s
10s
5min
10min
30min
0s
+∞
+∞
10min
30min
+∞
+∞
+∞
+∞
+∞
+∞
10s
10%
10%
10%
10%
Disable
10%
30%
10%
10%
10%
30%
10%
10%
10%
30%
10%
Disable
2Lux
10Lux
30Lux
10Lux
30Lux
Disable
2Lux
10Lux
30Lux
Disable
30Lux
10Lux
50Lux
Disable
2Lux
Hold
time
Stand-by
time
Stand-by
dimming level
Daylight
threshold
4. Functions
HMW30-20180529-A2
Rated load
A. Ceiling mount
B. Screw to the Luminaire by conduit
C. Attach to the shade by clamp
24.5
91.5
59.3
57.3
47.5
4.1
80.7
75
4.1
66.6
81.5
59.6
66.6
89.9
0.825”
75
64
59.3
57.3
35.2
47.5
84.5
59.3
29
163.2
66.6
75
33.7
15
28.5
4.5
4.5
59.6
Sensor module
Daylight sensor
LED indicator
Infrared receiver
Rotary switch
Cable entry
Installation rack
Sensor module
Daylight sensor
LED indicator
Infrared receiver
Rotary switch
Cable entry
Sensor module
Daylight sensor
LED indicator Infrared receiver
Rotary switch
Angle adjustment
Luminaire clamp
Note:We recommend the mounting distance between sensor to sensor
should be more than 2m to prevent sensors from false-triggering.
zero-cross point
Alternating current
4.2 Zero-cross Relay Operation
Designed in the software, sensor switches on/off the load right at the zero-cross point, to ensure
that the in-rush current is minimised, enabling the maximum lifetime of the relay.
4.1 On/off Control
This sensor is a motion switch, which turns on the light upon detection of motion, and turns off after a
pre-selected hold-time when there is no movement. A daylight sensor is also built in to prevent the light
from switching on when there is sufficient natural light.
Installation Height : 20m (forklift) 15m (person)
Detection Range (Ø) :20m
5. Wiring Diagram
8. Trouble Shooting
Descriptions of the
Button Functions
(remote control HRC-11)
MALFUNCTION CAUSE REMEDY CAUSE REMEDY
The fixture does not light up
The fixture is always on
Check detection area setting
The fixture is on when it should not
Incorrect daylight threshold setting
Continous movement in the detection zone
Sudden change in temperature due to weather (wind, rain, snow) or air
expelled from fans, open windows
Detection zone not targeted
Faulty fixture
No power supply
Adjust daylight threshold setting
Replace fixture
Check power to sensor
Check detection area setting
Adjust zone, change installation site
7. Permanent ON/OFF [ ]
Press button to select permanent ON or permanent OFF mode.
* Press button / to resume automatic operation.
The mode will change to AUTO Mode after power failure.
Power output [ button ]
Press button , the light output shifts between 80% and 100%.
Note: the function of “Sensor off” and “Twilight” are disabled.
Detection range [ zone ]
Press buttons in zone to set detection range at 100% / 75% /
50% / 10%.
Daylight threshold [ zone ]
Press buttons in zone to set the daylight sensor at 2Lux / 10Lux /
50Lux / 100Lux / 300Lux / 500Lux or Disable.
Note: To set daylight sensor at 100Lux / 300 Lux / 500Lux, press
button Shift at first.
button
Auto Mode [ button ]
Brightness +/- [ button ]
Scene prog. [ zone ] (One-key-commissioning)
Shift [ button ]
RESET [ button ]
Press button , all settings go back to the rotary switch settings.
Press button to initiate automatic mode. The sensor starts working
and all settings remain as before the light was switched ON/OFF.
Note: the function of Semi-auto is disabled.
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, / “Daylight threshold”,
“Hold time”, “Stand-by time”, “Stand-by dimming level” to
set all parameters.
3. Press button “Memory” to save all the settings programmed in the
remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to pre-set detection range 100%, daylight threshold
Disable, hold time 5min, stand-by time +∞, stand-by dimming level
30%, the steps should be as follows:
Press button Start, button 100%, Disable, Shift, 5min,
Shift, +∞ , 30%, Memory. By pointing to the sensor unit(s)
and pressing Apply, all settings are passed on the sensor(s).
Press button , the LED on the top left corner is on for indication.
All values / settings in RED are valid for 20 seconds.
18
3
9
Dual tech & RF mode [ zone ]
All buttons in zone are disabled.
14
14
Hold time [ zone ]
2
11
11
11
Ambient daylight threshold [ button ]
1. Press button Shift, the red LED is on for indication.
2. Press button , the ambient lux level is sampled and set as the
new daylight threshold.
3
10
10
9
8
2
2
3
3
4
4
5
6
7
7
7
7
3
3
8
8 9
10
10 11
1312
11 12 13
5
1
2 4
3
HMW30-20180529-A2
Hytronik Industrial Ltd. | www.hytronik.com
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bo'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel: 86-752-2772020 Fax: 86-752-2777877
HRC-11
&
A
4 hh
4h
1
3
7
9
6
8
10
11
12
13
14
2
4
5
HMW30
Brown
LED driver
L
N
L
N
Blue
Grey
These two buttons are disabled.
Press buttons in zone to set the hold time at 2s / 30s / 1min /
5min / 10min / 15min / 20min / 30min.
Note: 1.To set hold-time at 30s / 5min / 15min / 30min, press button
Shift at first.
2. 2s is for testing purpose only, stand-by period and daylight
sensor settings are disabled in this mode.
*To exit from Test mode, press button or any button in zone .
10%
30%
75%
50%
Ceiling mounted detection pattern (m)
Ceiling mounted height(m)
10
0
20
Detection Pattern6.
* For single person walking across, the detection range is reduced by 1/3.
Stand-by time [ zone ]
12
12
All buttons in zone are disabled.
Stand-by dimming level [ zone ]
13
13
All buttons in zone are disabled.
(forklift)
  • Page 1 1
  • Page 2 2

Hytronik IP65 High Bay HF Sensor HMW30 User manual

Hytronik
Brand
Hytronik
Model
IP65 High Bay HF Sensor HMW30
Category
Motion detectors
Type
User manual
This manual is also suitable for

Hytronik IP65 High Bay HF Sensor HMW30

The Hytronik IP65 High Bay HF Sensor HMW30 is a high-quality motion sensor designed for use in demanding environments. With its IP65 rating, it is dust-tight and protected against water jets, making it ideal for use in outdoor or harsh industrial settings.

The HMW30 uses advanced high-frequency (HF) technology to detect movement, providing a wide detection range of up to 20 meters in diameter when mounted on a ceiling at a height of 20 meters. It has a built-in daylight sensor that prevents the light from switching on when there is sufficient natural light, saving energy.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents