MTX RZRXP-10 Owner's manual

Category
Speaker sets
Type
Owner's manual

MTX Audio RZRXP-10 is a 10-inch all-weather amplified subwoofer enclosure that is perfect for adding some serious bass to your Polaris RZR. With 250 watts of RMS power and 500 watts of peak power, this subwoofer will provide you with plenty of low end to enjoy your music. The integrated amplifier and power and ground connections make installation a breeze, and the low-level input with external gain control allows you to customize the sound to your liking.

MTX Audio RZRXP-10 is a 10-inch all-weather amplified subwoofer enclosure that is perfect for adding some serious bass to your Polaris RZR. With 250 watts of RMS power and 500 watts of peak power, this subwoofer will provide you with plenty of low end to enjoy your music. The integrated amplifier and power and ground connections make installation a breeze, and the low-level input with external gain control allows you to customize the sound to your liking.

MTX.COM
OWNER’S MANUAL
RZRXP-10
POLARIS
®
RZR
®
AMPLIFIED SUBWOOFER ENCLOSURE
MTX.COM
2
IMPORTANT NOTICE
If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support
at 1-800-225-5689.
When connecting power and ground wires ensure that the red power wire is fused at the point
where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a
short circuit develops between the vehicle connection point and the product.
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
IN THE BOX
• RZRXP-10AmpliedSubwooferEnclosure
• EBCandEBCExtensionWire
Mounting Hardware
(1)1"T30TorxScrew
(2)1.5"T30TorxScrews
ADDITIONAL ACCESSORIES NEEDED AND NOT INCLUDED
MTX recommends using StreetWires PS1K-10 amp kit which includes the following:
• PowerandGroundWiretoRuntotheBattery
• 20AATCFuseHolderandFuse
• AccessoryConnectionWire
• RCACablestoConnecttotheSource
INSTALLATION TOOLS
The following is a list of suggested tools needed for installation:
• Torx-T40
• Torx-T30
• Torx-T25
10mm Wrench or Socket
Razor Knife
INTRODUCTION
ThankyouforpurchasingtheMTXAudioampliedsubwooferenclosuredesignedforthePolaris
®
RZR
®
.TheeasytoinstallsubwooferistheperfectdirecttbasssolutionforyourPolaris
®
RZR
®
.
CongratulationsandenjoytheultimateaudioexperiencewithMTX!
FITS THE FOLLOWING VEHICLES
• RZR
®
XP/XP41000(2014andUp)
• RZR
®
XP/XP4TURBO(2016andUp)
• RZR
®
900/900S/1000S(2015andUp)
• RZR
®
4900EPS(2015andUp)
NOTE:Willnottonvehicleswiththeaddedheateraccessory.
MTX.COM
3
FEATURES
• 10"All-WeatherAmpliedSubwooferEnclosure
• Integrated250-WattRMS/500-WattPeakPowerAmplier
• IntegratedPowerandGroundConnections
• LowLevelInputwithExternalGainControl
• DashMountBassControlKnob(Included)
• MountsUnderneathDashboard-DirectFit,NoDrillingRequired
SPECIFICATIONS
RMS Power Handling: 250-Watts
Peak Power Handling: 500-Watts
• FrequencyResponse:34Hz-120Hz
MTX.COM
4
INSTALLATION
Step 1 - Release the two quick locks to remove the hood from the vehicle.
Step 2 - Lift up the hood and slide towards the front of the vehicle.
Step3-Removethetwo(2)T40screwsholdingdownthetopdashcover.
MTX.COM
5
Step4-Liftandpullbackthetopdashcovertoreleasetheclipsholdingitinplace.Unplugthegauge
and switches making sure not to damage the vehicle and ignition wiring. Make note to remember
whatconnectorisassociatedwitheachspecicswitch.
Step5-RemovetheTorxheadscrewfromthedashpocketbrace.Afterthisisremovedtheplastic
dash pocket and bracket can be pulled out of the dash.
MTX.COM
6
Step6-Removethetwo(2)T40screwsholdingthedashboardinplace.
Step 7 - Pull the dashboard towards the back of the vehicle. There are locking clips on the right and
left side that hold it in place. The dash will pop out.
MTX.COM
7
Step 8 - Carefullylift the dash out of the vehicle. If the locking clips have fallen off, place them back
onto the locking tabs on the dash. These are needed to re-assemble the dashboard.
Step9-Removethetwo(2)10mmhexboltsthatareholdingthegloveboxtothevehicleframe.When
thescrewsareremovedthegloveboxcanbelowereddownandoutoftheenclosure.
Step10-Removetheve(5)T25screwsholdingthegloveboxtogether.Thegloveboxwillthenopen
like a book.
MTX.COM
8
Step11-Cutthe“binding”plastichingewitharazorknifetoseparatethefrontandbackoftheglove
box.Thebacksideofthegloveboxwillnolongerbeused.Thefrontsideofthegloveboxwillbe
attached to the enclosure.
Step12-Usingtheve(5)T25screwsthatwereremovedfromthefront/backassemblyoftheglove
box,attachthefrontofthegloveboxtotheRZRXP-10enclosure.Takecaretonotstripouttheplastic,
buttightenitenoughsotheenclosureandgloveboxaresolidlyconnected.
Step 13 - The enclosure can now be placed into the vehicle. Place the rectangular protrusion at an
angleintothedasharearst.Theenclosurecantheneasilyslideupintoplace.
MTX.COM
9
Step14-Holdtheenclosureupandalignthegloveboxscrewholeswiththevehicleframemount.
Replacethetwo(2)10mmhexboltsandtightentheenclosureinplace.Itmayhelptoplacea
supportingobjectundertheenclosuresobothhandsarefreetolineupthescrewholeswiththe
vehicle frame mount.
Step 15 - There are three mounting holes on the bottom of the enclosure to screw the base of
the enclosure into place. The furthest hole to the right uses the included 1" screw. The other two
mounting holes use the 1.5" screws. Tighten the screws down, but take care to not strip them. These
screws lock into the plastic foot board.
MTX.COM
10
Step 16 - Now that the enclosure is securely tightened in place, the power and signal wires need to
be connected to the battery and signal source.
• The Red wire should be connected directly to the battery’s positive terminal and fused with a
30A fuse.
• The Blackwireshouldbedirectlyconnectedtothebattery’snegativeterminal.
If your vehicle is equipped with the Polaris
®
bussbarkit,theRedandBlackwirescanbe
connectedtothebussbarunderthehoodontherewall.TheRedwirewillstillneedtobe
fused.
• The BluewirecanbeconnectedtotheACC/KeyTurnOnlocatedonthebussbarofanyvehicle.
Step17-ConnecttheRCAinputstothesignalsourceofyourchoice
Step 18 - Turn the unit on and check to make sure everything works. Set the gain using the gain pot
that is attached to the orange / grey wires. Set the gain to the bass level desired.
Step19-TheincludedEBCcanbeconnectedandmountedtoadesiredlocationtoalloweasytrim
adjustmentofthebasslevelafterthegainhasbeenset.
Step 20 - Replace all the parts and screws that have been removed to return the RZR back to its
completely assembled state.
MTX.COM
11
For proper perfomance and safety, MTX recommends installing an inline fuse per the owner’s manual
instructions according to the following.
TROUBLESHOOTING
UTVThunderForm 30A Fuse
Problem Cause Solution
NoLEDIndication
No+12VatRemoteConnection Supply+12VtoTerminal
No+12VatPowerConnection Supply+12VtoTerminal
InsufcientGroundConnection VerifyGroundConnection
BlownPowerFuse
Removethe6TorxScrewsonthe
PerimeteroftheAmplier.Carefully
RemovetheAmpliertoAccessthe
FuseHolderonthePowerCable.
Replace with a 30A Fuse.
PowerLEDOn,
NoOutput
VolumeonSourceUnitOff IncreaseVolumeonSourceUnit
GainControlonAmplierOff TurnUpGain
IndicatorLEDSolidRed SpeakerorAmplierDefective
OutputDistorted
HeadUnitVolumeSetTooHigh LowerHeadUnitVolume
AmplierGainSetTooHigh LowerAmplierGain
BassisWeak
SpeakersWiredOutofPhaseFrom
the Subwoofer
WireSpeakerswithCorrectPhase
BlowingFuses
ExcessiveOutputLevels LowertheVolume
AmplierDefective Return for Service
MTX.COM
12
© 2016 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. All other trademarks
are property of their respective owners. Designed and Engineered in the U.S.A.
Due to continual product development, all specications are subject to change without notice.
MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689
MTX005491 RevC 9/17 • 21A10545 • AW0015387
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

MTX RZRXP-10 Owner's manual

Category
Speaker sets
Type
Owner's manual

MTX Audio RZRXP-10 is a 10-inch all-weather amplified subwoofer enclosure that is perfect for adding some serious bass to your Polaris RZR. With 250 watts of RMS power and 500 watts of peak power, this subwoofer will provide you with plenty of low end to enjoy your music. The integrated amplifier and power and ground connections make installation a breeze, and the low-level input with external gain control allows you to customize the sound to your liking.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI