MTX Audio RZRXP-10 Owner's manual

Brand: MTX Audio

Model: RZRXP-10

Category: Speaker sets

Type: Owner's manual

MTX Audio RZRXP-10 is a 10-inch all-weather amplified subwoofer enclosure that is perfect for adding some serious bass to your Polaris RZR. With 250 watts of RMS power and 500 watts of peak power, this subwoofer will provide you with plenty of low end to enjoy your music. The integrated amplifier and power and ground connections make installation a breeze, and the low-level input with external gain control allows you to customize the sound to your liking.

MTX.COM

OWNER’S MANUAL

RZRXP-10

POLARIS

RZR

AMPLIFIED SUBWOOFER ENCLOSURE

MTX.COM

IMPORTANT NOTICE

If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support

at 1-800-225-5689.

When connecting power and ground wires ensure that the red power wire is fused at the point

where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a

short circuit develops between the vehicle connection point and the product.

PRODUCT INFORMATION

Model #

Serial #

Dealer’s Name

Date of Purchase

IN THE BOX

• RZRXP-10AmpliedSubwooferEnclosure

• EBCandEBCExtensionWire

• Mounting Hardware

  (1)1"T30TorxScrew

  (2)1.5"T30TorxScrews

ADDITIONAL ACCESSORIES NEEDED AND NOT INCLUDED

MTX recommends using StreetWires PS1K-10 amp kit which includes the following:

• PowerandGroundWiretoRuntotheBattery

• 20AATCFuseHolderandFuse

• AccessoryConnectionWire

• RCACablestoConnecttotheSource

INSTALLATION TOOLS

The following is a list of suggested tools needed for installation:

• Torx-T40

• Torx-T30

• Torx-T25

• 10mm Wrench or Socket

• Razor Knife

INTRODUCTION

ThankyouforpurchasingtheMTXAudioampliedsubwooferenclosuredesignedforthePolaris

RZR

.TheeasytoinstallsubwooferistheperfectdirecttbasssolutionforyourPolaris

RZR

CongratulationsandenjoytheultimateaudioexperiencewithMTX!

FITS THE FOLLOWING VEHICLES

• RZR

XP/XP41000(2014andUp)

• RZR

XP/XP4TURBO(2016andUp)

• RZR

900/900S/1000S(2015andUp)

• RZR

4900EPS(2015andUp)

NOTE:Willnottonvehicleswiththeaddedheateraccessory.

MTX.COM

FEATURES

• 10"All-WeatherAmpliedSubwooferEnclosure

• Integrated250-WattRMS/500-WattPeakPowerAmplier

• IntegratedPowerandGroundConnections

• LowLevelInputwithExternalGainControl

• DashMountBassControlKnob(Included)

• MountsUnderneathDashboard-DirectFit,NoDrillingRequired

SPECIFICATIONS

• RMS Power Handling: 250-Watts

• Peak Power Handling: 500-Watts

• FrequencyResponse:34Hz-120Hz

MTX.COM

INSTALLATION

Step 1 - Release the two quick locks to remove the hood from the vehicle.

Step 2 - Lift up the hood and slide towards the front of the vehicle.

Step3-Removethetwo(2)T40screwsholdingdownthetopdashcover.

MTX.COM

Step4-Liftandpullbackthetopdashcovertoreleasetheclipsholdingitinplace.Unplugthegauge

and switches making sure not to damage the vehicle and ignition wiring. Make note to remember

whatconnectorisassociatedwitheachspecicswitch.

Step5-RemovetheTorxheadscrewfromthedashpocketbrace.Afterthisisremovedtheplastic

dash pocket and bracket can be pulled out of the dash.

MTX.COM

Step6-Removethetwo(2)T40screwsholdingthedashboardinplace.

Step 7 - Pull the dashboard towards the back of the vehicle. There are locking clips on the right and

left side that hold it in place. The dash will pop out.

MTX.COM

Step 8 - Carefullylift the dash out of the vehicle. If the locking clips have fallen off, place them back

onto the locking tabs on the dash. These are needed to re-assemble the dashboard.

Step9-Removethetwo(2)10mmhexboltsthatareholdingthegloveboxtothevehicleframe.When

thescrewsareremovedthegloveboxcanbelowereddownandoutoftheenclosure.

Step10-Removetheve(5)T25screwsholdingthegloveboxtogether.Thegloveboxwillthenopen

like a book.

MTX.COM

Step11-Cutthe“binding”plastichingewitharazorknifetoseparatethefrontandbackoftheglove

box.Thebacksideofthegloveboxwillnolongerbeused.Thefrontsideofthegloveboxwillbe

attached to the enclosure.

Step12-Usingtheve(5)T25screwsthatwereremovedfromthefront/backassemblyoftheglove

box,attachthefrontofthegloveboxtotheRZRXP-10enclosure.Takecaretonotstripouttheplastic,

buttightenitenoughsotheenclosureandgloveboxaresolidlyconnected.

Step 13 - The enclosure can now be placed into the vehicle. Place the rectangular protrusion at an

angleintothedasharearst.Theenclosurecantheneasilyslideupintoplace.

MTX.COM

Step14-Holdtheenclosureupandalignthegloveboxscrewholeswiththevehicleframemount.

Replacethetwo(2)10mmhexboltsandtightentheenclosureinplace.Itmayhelptoplacea

supportingobjectundertheenclosuresobothhandsarefreetolineupthescrewholeswiththe

vehicle frame mount.

Step 15 - There are three mounting holes on the bottom of the enclosure to screw the base of

the enclosure into place. The furthest hole to the right uses the included 1" screw. The other two

mounting holes use the 1.5" screws. Tighten the screws down, but take care to not strip them. These

screws lock into the plastic foot board.

MTX.COM

Step 16 - Now that the enclosure is securely tightened in place, the power and signal wires need to

be connected to the battery and signal source.

• The Red wire should be connected directly to the battery’s positive terminal and fused with a

30A fuse.

• The Blackwireshouldbedirectlyconnectedtothebattery’snegativeterminal.

• If your vehicle is equipped with the Polaris

bussbarkit,theRedandBlackwirescanbe

  connectedtothebussbarunderthehoodontherewall.TheRedwirewillstillneedtobe 

fused.

• The BluewirecanbeconnectedtotheACC/KeyTurnOnlocatedonthebussbarofanyvehicle.

Step17-ConnecttheRCAinputstothesignalsourceofyourchoice

Step 18 - Turn the unit on and check to make sure everything works. Set the gain using the gain pot

that is attached to the orange / grey wires. Set the gain to the bass level desired.

Step19-TheincludedEBCcanbeconnectedandmountedtoadesiredlocationtoalloweasytrim

adjustmentofthebasslevelafterthegainhasbeenset.

Step 20 - Replace all the parts and screws that have been removed to return the RZR back to its

completely assembled state.

MTX.COM

For proper perfomance and safety, MTX recommends installing an inline fuse per the owner’s manual

instructions according to the following.

TROUBLESHOOTING

UTVThunderForm 30A Fuse

Problem Cause Solution

NoLEDIndication

No+12VatRemoteConnection Supply+12VtoTerminal

No+12VatPowerConnection Supply+12VtoTerminal

InsufcientGroundConnection VerifyGroundConnection

BlownPowerFuse

Removethe6TorxScrewsonthe

PerimeteroftheAmplier.Carefully

RemovetheAmpliertoAccessthe

FuseHolderonthePowerCable.

Replace with a 30A Fuse.

PowerLEDOn,

NoOutput

VolumeonSourceUnitOff IncreaseVolumeonSourceUnit

GainControlonAmplierOff TurnUpGain

IndicatorLEDSolidRed SpeakerorAmplierDefective

OutputDistorted

HeadUnitVolumeSetTooHigh LowerHeadUnitVolume

AmplierGainSetTooHigh LowerAmplierGain

BassisWeak

SpeakersWiredOutofPhaseFrom

the Subwoofer

WireSpeakerswithCorrectPhase

BlowingFuses

ExcessiveOutputLevels LowertheVolume

AmplierDefective Return for Service

MTX.COM

are property of their respective owners. Designed and Engineered in the U.S.A.

Due to continual product development, all specications are subject to change without notice.

MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689

MTX005491 RevC 9/17 • 21A10545 • AW0015387

MTX Audio RZRXP-10 Owner's manual

Brand: MTX Audio

Model: RZRXP-10

Category: Speaker sets

Type: Owner's manual

Download PDF

report

MTX Audio RZRXP-10 Owner's manual

MTX Audio RZRXP-10 Owner's manual

Related papers

Other documents