Instruction manual
Brings up data broadcast screen
for data broadcasting programs.
Data button
After setting the manufacturer of your
TV (see next page), this remote control
can be used to operate your TV.
After setting the manufacturer of your
TV (see next page), this remote control
can be used to operate your TV.
TV control
Turns tuner ON or OFF.
Tuner power button
TV control
Brings up number entry screen for
selecting channels directly using number
buttons.
Channel number entry button
Selects "Japanese", "Original-language",
or "Japanese + Original-language".
Changes language for bilingual broadcasts.
Audio-select button
Selects controllable digital tuner.
Select same number as "Remote
control select setup (p.74)".
Tuner-select switch
Enlarges image on screen.
Refer to Japanese instruction manual
for explanation of other buttons.
Zoom button
Changes your selection (highlighted item)
on the selection or setting screens and
activates your selection.
, Entry button
Brings up "" (menu)
setting screen.
MENU button
Brings up Electronic Program
Guide (EPG) screen "" of
current broadcast selection.
EPG button
Select for terrestrial "",
satellite(BS) or CS broadcasts.
Broadcast-select button
Changes channel by moving up or
down through all channels.
Channel button
Select terrestrial digital broadcast
channels, BS digital broadcasts
channels and 110˚CS digital broadcasts
channels with buttons numbered
to .
Press the channel number entry button
then to can also be
used to select.
( button functions as "0".)
Press the next button
within 10 seconds.
Number buttons
Example : For "011"
Press the buttons in order.
Instruction manual
Example
Instruction manual (Continued)
Basic operation for digital TV viewing
Television operation setting
When image freezes and / or operation is disabled
Precautions
"Tuner-select switch" on remote control must be set to same number as "Remote
control select setup (p.74)". Operation cannot be enabled until this is done.
Turn on Power Supply switch.
Press to select program.
If reset button does not enable operation,
pull out plug from wall outlet and plug it in
again for recovery.
Press to bring up
sub menu screen.
Press to bring up EPG.
Press for sequential
selection.
Press power button of Remote control.
Select a program from the following A or B.
Press to select ",
" or
".
Press to tune
in to program.
ASelect channels one by one
BTune it in with EPG
Tuner-select switch
Refer to Japanese instruction manual for further details.
B
A
Set the number of corresponding
manufacturer. When there is more than
one number, try each until you find the
one that enables operation of your TV.
Manufacturer
Panasonic
SHARP
MITSUBISHI
Victor
HITACHI
SANYO
SONY
NEC
FUJITSU GENERAL
01, 02
03, 04, 47
05, 06
07, 44, 45
08
09, 10, 46
11, 50
12, 51
13, 48, 49
Pioneer
AIWA
SUMSUNG
FUNAI
TOSHIBA
LG
PHILIPS
ORION
—
14
15, 16, 17
18, 19, 20, 21, 22
23, 24, 25, 26, 27, 28
29, 30, 31
32, 33, 34, 35, 36, 37, 38
39, 40, 41
42, 43
—
Number Manufacturer Number
Push reset button.
Example : FOR television manufacturer number "01".
( button functions as "0".)
While pushing (TV Power button)
Push and buttons in order.
How to set manufacturer number
Instruction manual
Reset button
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Dreambox DM7020 HD User manual
-
Devolo dLAN TV Sat PC Owner's manual
-
Wintal PD1200HD User manual
-
JVC TU-DB1SFR User manual
-
-
Sanyo LCD32F1080P User manual
-
Hitachi L42VP01U Instructions For Use Manual
-
-
Dream Dreambox DM800 HD se Owner's manual
-
