Minka Ceiling Fan Co. 84013 Installation guide

Brand
Minka Ceiling Fan Co.
Model
84013
Type
Installation guide

This manual is also suitable for

Minka Ceiling Fan Co. 84013 is a 50-inch smart ceiling fan featuring an energy-saving DC motor and a 20W LED light. The 3-blade fan offers 6-speed options and a reversible motor for year-round comfort. It comes with a hand-held remote control for easy operation and allows for customization using the "Learning Mode" feature. The fan also includes a light kit with an acrylic shade for added illumination. With its sleek modern design and whisper-quiet operation, the Minka Ceiling Fan Co. 84013 is not only stylish but also functional, providing both comfort and convenience to your space.

Minka Ceiling Fan Co. 84013 is a 50-inch smart ceiling fan featuring an energy-saving DC motor and a 20W LED light. The 3-blade fan offers 6-speed options and a reversible motor for year-round comfort. It comes with a hand-held remote control for easy operation and allows for customization using the "Learning Mode" feature. The fan also includes a light kit with an acrylic shade for added illumination. With its sleek modern design and whisper-quiet operation, the Minka Ceiling Fan Co. 84013 is not only stylish but also functional, providing both comfort and convenience to your space.

ANZANI
50" Ceiling fan
84011,84012,84013
Minka
Minka
Minka
Minka
Minka
Minka
RC120-HL
DC8
MORE NOT LESS
1. Fan body
2. 20W LED light kit
3. Fan blade(3 pcs)
4. canopy
5. light kit plate
6. light shade
7. downrod assembly
8. hanger bracket
9. coupling cover
10. canopy cover
11. Hand Held Remote+holder+2
Mounting Screws+ 1.5v *2 Battery
12. receiver(8 pcs wire nuts)
A. Blade attachment hardware
1/4x13mm+S screws(10pcs)
B. Mounting hardware
#8-32*38mm screw(2pcs)
#10x38mm wood screw(2 pcs)
Φ5*14*1mm flat washer(2 pcs)
5/32(Φ4.4*9.4*0.5-1.0mm-10) star washer(2pcs)
3/16(Φ5.2*8.4*1.0mm) spring washer(2pcs)
C. Balance kit
D. wire nut(3pcs)
Minka
Minka
35
Minka Minka
Step 2: Remove the hitch pin and lock pin from downrod assembly. （Fig.6）
DOWNROD
SER
SCREWS
HITCH PIN
LOCK PIN
DOWNROD
COUPLING
COVER
OUTLET BOX
HANGER
BRACKET
(Fig.7&Fig.8&Fig.9)
HANGER
BALL
CANOPY
CANOPY
COVER
COUPLER
COVER
BLACK
WHITE
GREEN
GREY
PURPLE
WHITE
RED
BLUE
RECEIVER
HANGER
BRACKET
SCREW
CANOPY
CANOPY COVER
motor
BLADE
SCREW
MOUNTING RING
SCREW
MOUNTING
RING
LIGHT KIT
PLATE
LIGHT KIT
PLATE
INSTALLING THE LIGHT KIT PLATE
light kit
light kit
LIGHT
KIT PLATE
SCREW
LIGHT KIT
PLATE
LED LIGHT KIT
Step3.Screw back the 3 previously removed screws and tighten the light kit.
light kit
Blue to Blue
FIG.16 FIG.17
(Fig.16)
(Fig.15)
(Fig.17)
LIGHT SHADE
light
18
light kit
FIG.18
when
ON/OFF
Dimming
Should
There is a "Universal Mode" and "Learning Mode" with the remote control.
When selecting "Universal Mode", simply place dip (code) switch to the UP
Position (COMMON CODE). There will be no need to pair your fan and
remote control.
Please Note: Under the universal mode setting, your fan can be controlled
by other transmitters also using the “Universal Mode” with no need to pair them.
To prevent any possible Interference with other fans in your home.
Minka recommends the use of the “Learning Mode” setting
by placing the dip (code) switch to the LOWER position (L. CODE) and follow
the steps below.
Learn Mode setting: Within 60 second of restoring power source to your fan, press
and hold the "LEARN" button for at least 3 seconds.
If the fan is installed with light, the light will blink 3 times.
This will indicate the process is complete and your fan is ready for use.
For fans without light, check operation using remote transmitter.
Note: Power must be off for a minimum of 10 seconds, before restoring power to attempt
the Learn Mode setting procedure.
Note:
If Multiple fans require to be controlled by a single remote transmitter Minka Recommends
Using the Learn Mode setting. Power to both fans will need to be restored at the same time and
Press the Learn button on the remote control so that both desired fans can receive the remotes signal simultaneously.
when
5. The controller is capable to recording 2 frequency setting, to avoid any frequency issues please ensure both
frequencies have been set.
19
20
FIG.19 FIG.20
There is a "Universal Mode" and "Learning Mode" with the remote control.
When selecting "Universal Mode", simply place dip (code) switch to the UP
Position (COMMON CODE). There will be no need to pair your fan and
remote control.
Please Note: Under the universal mode setting, your fan can be controlled
by other transmitters also using the “Universal Mode” with no need to pair them.
To prevent any possible Interference with other fans in your home.
Minka recommends the use of the “Learning Mode” setting
by placing the dip (code) switch to the LOWER position (L. CODE) and follow
the steps below.
Learn Mode setting: Within 60 second of restoring power source to your fan, press
and hold the "LEARN" button for at least 3 seconds.
If the fan is installed with light, the light will blink 3 times.
This will indicate the process is complete and your fan is ready for use.
For fans without light, check operation using remote transmitter.
Note: Power must be off for a minimum of 10 seconds, before restoring power to attempt
the Learn Mode setting procedure.
Note:
If Multiple fans require to be controlled by a single remote transmitter Minka Recommends
Using the Learn Mode setting. Power to both fans will need to be restored at the same time and
Press the Learn button on the remote control so that both desired fans can receive the remotes
signal simultaneously.
18
Minka
50
0.09
0.47
1.62
30.32
33
182
359
3390
5.2 7.0 2.05
6
1,970
100
20
19
MKA19102501
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Minka Ceiling Fan Co. 84013 Installation guide

Brand
Minka Ceiling Fan Co.
Model
84013
Type
Installation guide
This manual is also suitable for

Minka Ceiling Fan Co. 84013 is a 50-inch smart ceiling fan featuring an energy-saving DC motor and a 20W LED light. The 3-blade fan offers 6-speed options and a reversible motor for year-round comfort. It comes with a hand-held remote control for easy operation and allows for customization using the "Learning Mode" feature. The fan also includes a light kit with an acrylic shade for added illumination. With its sleek modern design and whisper-quiet operation, the Minka Ceiling Fan Co. 84013 is not only stylish but also functional, providing both comfort and convenience to your space.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents