CR800 ENT FITNESS BIKE
OWNER’S MANUAL
TABLE OF CONTENTS
3 IMPORTANT SAFETY INSTRUCTIONS
3 IMPORTANT ELECTRICAL INSTRUCTIONS
4 PRODUCT REGISTRATION
4 IMPORTANT OPERATION INSTRUCTIONS
5 CR800 ENT ASSEMBLY INSTRUCTIONS
11 CONSOLE OPERATION
23 PROGRAMMABLE FEATURES
34 USING HEART RATE TRANSMITTER
37 GENERAL MAINTENANCE
38 MANUFACTURER’S LIMITED WARRANTY
Thank you for purchasing our product, please save these instructions. Please do not perform or attempt any
customizing, adjustments, repair or maintenance that is not described in this manual.
2
Congratulations on your new tness bike and welcome to the Spirit Fitness family!
Thank you for your purchase of this quality tness bike from Spirit Fitness. Your new tness bike was manufactured by one
of the leading tness manufacturers in the world and is backed by one of the most comprehensive warranties available.
Through your dealer, Spirit Fitness will do all we can to make your ownership experience as pleasant as possible for many
years to come. If not purchased direct from Spirit Fitness, the local dealership where you purchased this tness bike is
your administrator for all Spirit Fitness warranty and service needs. Their responsibility is to provide you with the technical
knowledge and service personnel to make your experience more informed and any difculties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number, and the date of purchase below
to make any future, needed contact easy. We appreciate your support and we will always remember that you are the reason
that we are in business.
Yours in Health,
Spirit Fitness
NAME OF DEALER _____________________________________
DEALER PHONE # _____________________________________
PURCHASE DATE _____________________________________
3
Important Safety Instructions
WARNING
• Before beginning this or any exercise program, consult a
physician. This is especially important for persons over the
age of 35 or persons with pre-existing health conditions.
• Keep children away from the tness bike. There are obvi-
ous pinch points and other
caution areas that can cause harm.
• Keep hands away from all moving parts.
• Never drop or insert any object into any openings.
• Do not use outdoors.
• Do not attempt to use your tness bike for any purpose
other than for the purpose it is intended.
• The hand pulse sensors are not medical devices. Various
factors, including the user’s movement, may affect the
accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate
trends in general.
• Wear proper shoes. High heels, dress shoes, sandals or
bare feet are not suitable for use on your tness bike.
Quality athletic shoes are recommended to avoid leg
fatigue.
• Maximum User Weight: 450 lbs
• This appliance is not intended for use by persons with
reduced physical, sensory or metal capabilities, or lack
of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Keep children under the age of 13 away from this
machine.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Electrical Instructions
WARNING
NEVER expose this tness bike to rain or moisture. This
product is NOT designed for use outdoors, near a pool
or spa, or in any other high humidity environment. The
operating temperature specication is 40 to 120 degrees
Fahrenheit, and humidity is 95% non-condensing (no water
drops forming on surfaces).
4
Important Operation Instructions
• NEVER operate this tness bike without reading and completely understanding the results of any operational change
you request from the computer.
• Understand that changes in resistance do not occur immediately. Set your desired resistance level on the computer
console and release the adjustment key. The computer will obey the command gradually.
• Use caution while participating in other activities while pedaling on your tness bike; such as watching television, reading,
etc. These distractions may cause you to lose balance which may result in serious injury.
• Do not use excessive pressure on console control keys. They are precision set to function properly with little nger
pressure.
Record Your Serial Number
Please record the serial number of this tness product in the space provided
below.
Serial Number:
Register Your Purchase
The self-addressed product registration card must be completed in full and returned to Spirit Fitness.
You can also go to http://www.spirittness.com/commercialwarrantyregistration.html under the Support
tab to register online.
Serial Number Location
5
CR800 ENT PRE ASSEMBLY
UNPACKING
1. Cut the straps, then along the dotted line on the bottom of the box; lift the box over
the unit and unpack.
2. Locate the hardware package. The hardware is separated into four steps. Remove
the tools rst. Remove the hardware for each step as needed to avoid confusion. The
numbers in the instructions that are in parenthesis (#) are the item number from the
assembly drawing for reference.
TOOLS INCLUDED:
14/15mm Wrench
12/14mm Wrench
Phillips Screwdriver
PARTS INCLUDED:
1 Main Frame
1 Console Mast
1 Rear Stabilizer
1 Seat Back Frame
1 Front Handle Bar
1 Handle Bar
1 Seat Back Cover
1 Console Mast Cover
1 Front Stabilizer Cover
1 Rear Stabilizer Cover
1 Console
1 Seat Cushion
2 Cup Holders
2 Pedals
1 Hardware Kit
6
CONSOLE FAN
CONSOLE
FRONT STABILIZER
CRANK ARMS
CONSOLE MAST COVER
MAIN FRAME
PULSE GRIPS
CUP HOLDER
REAR STABILIZER
PEDALS
CONSOLE MAST
SEAT
FRONT HANDLEBARS
7
CR800 ENT STEP ONE
4
21
89
89
77
77
77
77
89
89
27
27
175
71
21
6
71
65
65
65
84
84
84
7
45
44
HARDWARE FOR STEP 1
PART TYPE DESCRIPTION QTY
65 BOLT
3/8”X2-1/4”
4
71 BOLT
3/8”X2”
4
77 FLAT WASHER
3/8”X19
6
84 FLAT WASHER
3/8”X1”
4
89 NYLON NUT
3/8”
6
175 BOLT 3/8X2-3/4” 2
1. Gather HARDWARE FOR STEP 1.
2. Install the REAR STABILIZER (7) onto the
MAIN FRAME with 4 BOLTS (65) and 4
WASHERS (84).
3. Install the HANDLEBAR ASSEMBLY (6) onto
the SEAT CARRIAGE (4) with 4 BOLTS (71)
installed through the top holes and secured with
4 FLAT WASHERS (77) and NYLON NUTS
(89). Install 2 BOLTS (175) through the side holes
and secure with 2 FLAT WASHERS (77) and
NYLON NUTS (89).
4. Plug the LEFT HAND PULSE WIRE (27) into
the corresponding LEFT SOCKET (42) located
in the left plastic side case under the seat carriage,
and the RIGHT HAND PULSE WIRE (21) into
the RIGHT SOCKET (26).
8
CR800 ENT STEP TWO
5
77
77
77
4
176
77
176
HARDWARE FOR STEP 1
PART TYPE DESCRIPTION QTY
77 FLAT WASHER
3/8”X19”
6
136 SCREW
M5X15
4
176 BOLT
3/8”X3/4”
6
1. Gather HARDWARE FOR STEP 2.
2. Install the SEAT BACK FRAME (5) onto the
SEAT CARRIAGE (4) with 6 BOLTS (176) and
FLAT WASHERS (77).
3. Install the SEAT BACK COVER (128) onto the
Seat Back with 4 PHILLIPS HEAD SCREWS
(136).
128
136
136
9
CR800 ENT STEP THREE
3
82
29
68
68
2
31
68
83
76
30
76
76
190
191
192
193
44
195
197
1
HARDWARE FOR STEP 3
PART TYPE DESCRIPTION QTY
68 BOLT
5/16”X5/8”
8
76 WASHER
5/16”X11/16”
6
82 SPLIT WASHER
5/16”
2
83 CURVED WASHER
5/16”X3/4”
2
1. Gather HARDWARE FOR STEP 3.
2. Install the CONSOLE MAST COVER (31)
onto the CONSOLE MAST (2), making
sure it is facing the correct direction as in the
picture below. Run the COMPUTER CABLE
(44), HANDPULSE WIRE(195), CSAFE W/
CABLE(190), TV SIGNAL CABLE(191),
NETWORK W/CABLE(192), CONSOLE
POWER CORD(193), and HDMI CABLE(197)
through the bottom of the console mast tube and
out the top opening.
3. Slide the CONSOLE MAST into the
RECEIVING TUBE (1) being careful to not pinch
the wires. Fasten the console mast with 6 BOLTS
(68) and 4 FLAT WASHERS (76) on the side
bolts and 2 CURVED WASHERS (83) on the
front bolts. Snap the CONSOLE MAST COVER
in place.
4. Install the FRONT HANDLEBARS (3) onto the
CONSOLE MAST with 2 BOLTS (68), SPLIT
WASHERS (82) and FLAT WASHERS (76).
10
CR800 ENT STEP FOUR
38
39
105
105
37
32
99
117
51R
51L
99
2
61
19
186
4
44
197
190
191
192
193
116
99
HARDWARE FOR STEP 4
PART TYPE DESCRIPTION QTY
186 SCREW
M6X18MM
4
99 SCREW
M5X12MM
10
105 SCREW
4MMX16MM
4
1. Gather HARDWARE FOR STEP 4.
2. Install the front and rear STABILIZER COVERS
(32 & 37) and secure to the frame with 4
SCREWS (99).
3. Install the left and right CUP HOLDERS (39
& 38) to the rear handlebars with 4 SELF
TAPPING SCREWS (105).
4. Install the bottom SEAT CUSHION (61) to the
SEAT CARRIAGE (4) with 4 SCREWS (98).
5. Install the PEDALS (116 L, 117 R) into the
CRANK ARMS (51 L, 51 R). Remember that
the left pedal has a reverse thread and will be
screwed in with the opposite rotation. Make sure
to tighten the pedals as much as you possibly can.
6. Connect the 7 WIRE HARNESSES
(44,195,190,191,192,193, & 197) to the
corresponding connectors on the back of
the console. Install the CONSOLE onto the
CONSOLE MAST and secure with 4 SCREWS
(99) being careful to not pinch the wires.
11
CU800 ENT CONSOLE OPERATION
Large Touch-
Screen LCD
Ten innovative
programs offer a
variety of work-outs
Fan to keep
you cool
Easy-Touch
Control Buttons
Convenient cargo
compartment for
keys, phone, or
MP3 player
12
Starting the operation
Plug in the power cord and switch on the main power switch located at the front base of the unit.
When the power is turned on, the screen will show the initial image and then enter the ready mode
which is the beginning of the treadmill operation.
First page for you to operate by touching the
icons.
Quick operating functional buttons are installed.
13
Quick Start
• Press Start button and the console starts performing the program. Press Level up/down buttons
further to change the resistance level you desire.
• Press rst page Home button or Stop button to stop the unit.
Featuring functions of this bike
Touch-control screen is installed for operating the bike. You can directly touch any functional button on
the screen or through quick buttons on the bottom to control. On the bottom, there are the Start
button to begin the workout, Stop button to pause/stop running and Fan button to turn the fan on or
off.
Pause/Stop
• Press Stop button once or Home button on the screen, the bike will stop and keep values of time,
distance and calorie on the screen. The screen will count down for 5 minutes then reset and return
to the initial status.
• Press Start button to continue the workout during pause.
• Press Stop button twice will terminate the setting with displaying the workout summary. If Stop
button is pressed the third time, the console will return to the initial status (the beginning).
14
Heart Rate Feature
The Pulse (Heart Rate) on the screen shows the current value of the heart beats per minute. You must
use both left and right stainless steel sensors to pick up your pulse. Pulse values are displayed anytime
the computer is receiving a Grip Pulse signal. You may use the Grip Pulse feature while in Heart Rate
Control. The Console will also pick up wireless heart rate transmitters that are bipolar compatible,
including signal transmitting.
To Turn Off The Bike
The screen will automatically turn off (go to sleep) after 30 minutes of inactivity. This function is called
sleep mode. In sleep mode, the bike will power down everything except for a minimum of circuitry for
detecting key presses, so it will start up again if this is activated. There is only a tiny amount of current
used in sleep mode (about the same as your TV when it is turned off) and it is perfectly ne to leave
the main power switch on in sleep mode.
15
Touch Screen Operation
Language
There are four items to be selected. Generally the
Language would be the rst item to select.
When you press the Language button on Home
page, it enters the menu with all language
selections.
There are 12 languages to choose. Touch the
desired language, and the system will return to
the rst page to begin the other program, or if
you don’t want to change the language, you could
press Home button at the upper left corner to
return to the rst page or touch the return icon
at right top corner to return to the previous page
to continue your operation.
16
TV
When the TV button on the Home page is pressed, it
directly enters TV interface.
Now you can enjoy TV programs. If you want to enjoy
TV while exercising, press Start button at front of the
treadmill to start it.
You can change the TV channel by using Up/Down
buttons on the TV channel or the channel control
panel buttons at the right side of the screen for quick
channel switching. You can also use up/down buttons
on the volume to change the sound volume. If you
want to be quiet, touch Mute button. Touch Max
Screen to switch to full screen. When you want to
resume the original screen display, just touch the image
and the screen resumes. Use Fast and Slow buttons
to control the speed and Up or Down button to set
the incline level during the exercise. When you want
to pause, just press Home button at left top or press
Stop button once and the pause window will show
up. If you want to stop, you can choose to end the
program or press Stop button again to terminate the
setting and show up the workout summary. If Stop
button is pressed the third time, it returns to the initial
status (the beginning)
17
Internet
When the Internet button on the Home page is
pressed, it directly enters Internet interface.
There are 6 internet connections to choose for you to
go on the internet while you are exercising. (internet
cable connection or WIFI connection is required)
When you want to pause, just press Home button
at left top or press Stop button once and the pause
window will show up. If you want to stop, you can
choose to end the program or press Stop button
again to terminate the setting and show up the
workout summary. If Stop button is pressed the third
time, it returns to the initial status (the beginning)
18
Exercise Programs
When the Exercise Program button on the Home
page is pressed, it directly enters Menu interface.
There are 10 program modes in Menu interface for
you to choose the desired program mode. For Manual
Program as an example, just touch Manual button on
the screen to enter the program for Manual.
MANUAL
Press Prole button to enter the Prole interface. If
this program is unwanted, just press Home icon at left
top to return to the rst page, or return icon at right
top to return to the previous page to continue the last
operation. If other prole is wanted, touch left or right
arrow button to choose the wanted program.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
