Winegard AP-8700 User manual

Type
User manual

This manual is also suitable for

Winegard Company3000 Kirkwood St.Burlington, IA 52601-2000800-288-8094fax 800-247-8221www.winegard.comPrinted in U.S.A. ©2011 Winegard Company WC-1051
Wiring Diagram for FREEVISION
®
Antenna to Television
FREEVISION
®
Antenna
(Side View—mount not included with all models)
Note: the matching transformer
must be connected as described
on page 4 of the manual.
Coax Cable
Antenna/Cable In
Coax Connection Port
Back of TV
Winegard model AP-8700 preamplifier and model PS-1403 power inserter are shown above.
Winegard Company3000 Kirkwood St.Burlington, IA 52601-2000800-288-8094fax 800-247-8221www.winegard.comPrinted in U.S.A. ©2011 Winegard Company WC-1051
Wiring Diagram for FREEVISION
®
Antenna with Preamplifier
FREEVISION
®
Antenna
(Side View—mount not included with all models)
Note: the matching transformer
must be connected as described
on page 4 of the manual.
Underside of Preamplifier
Antenna Input
Power Supply Input
Ant.
Input
Power
Input
TV Input
Slide a weather
boot over each
coax cable.
3’–6’ Standard Coax Cable
Coax Cable Coax Cable
AC Adaptor
Winegard model AP-8700 preamplifier and model PS-1403 power inserter are shown above.
Power
Inserter
Coax Cable
Antenna/Cable In
Coax Connection Port
Back of TV
Winegard Company3000 Kirkwood St.Burlington, IA 52601-2000800-288-8094fax 800-247-8221www.winegard.comPrinted in U.S.A. ©2011 Winegard Company WC-1051
Coax Connection on TV
Antenna/Cable In
Coax Connection Port
Wiring Diagram for FREEVISION
®
Antenna with Existing Indoor Coax Connection
FREEVISION
®
Antenna
Existing Coax
Connection*
Coa
x
Cable
Coax Cable
*The existing coax connection may be a 2-, 3-, 4- or 6- port splitter. A 2-port splitter is shown here.
Depending on the amount of signal received, a distribution amplifier may be required to power the system. Winegard recommends model HDA-100 distribution amplifier.
Coa
x
Cable
Winegard Company3000 Kirkwood St.Burlington, IA 52601-2000800-288-8094fax 800-247-8221www.winegard.comPrinted in U.S.A. ©2011 Winegard Company WC-1051
Coax Connection on TV
Antenna/Cable In
Coax Connection Port
Wiring Diagram for FREEVISION
®
Antenna with Grounding Block and Existing Coax Connection
Coax
Ca
b
l
e
*The existing coax connection may be a 2-, 3-, 4- or 6- port splitter. A 2-port splitter is shown here.
Depending on the amount of signal received, a distribution amplifier or preamplifier may be required to power the system. Winegard recommends model HDA-100 distribution amplifier or AP-8700 preamplifier.
Refer to the National Electronic Code for antenna grounding specifications.
Existing Coax
Connection*
OUT
OUT
IN
Coax Cable
Point toward
stations.
FREEVISION
®
Antenna
Grounding
Block
Note: ground wire
(#8 or larger)
must run from
grounding block
to ground rod
(not shown here).
Winegard Company3000 Kirkwood St.Burlington, IA 52601-2000800-288-8094fax 800-247-8221www.winegard.comPrinted in U.S.A. ©2011 Winegard Company WC-1051
Wiring Diagram for FREEVISION
®
Antenna with Preamplifier, Grounding Block & Existing Coax Connection
*The existing coax connection must be a splitter that is AC/DC passive on one leg only. The power supply must be connected to the AC/DC passive leg of the existing coax connection.
Refer to the National Electronic Code for antenna grounding specifications.
Existing Coax
Connection*
Note: ground wire
(#8 or larger)
must run from
grounding block
to ground rod
(not shown here).
OUT
OUT
IN
Coax
Ca
b
l
e
Power
Inserter
Grounding
Block
Point toward
stations.
FREEVISION
®
Antenna
Preamplifier Connections Coax Connection on TV
Antenna/Cable In
Coax Port
Preamplifier
Antenna Input
Power Supply Input
Underside of Preamplifier
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Winegard AP-8700 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI