2. Arris
  3. HD-DTA100u

Arris HD-DTA100u Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Arris HD-DTA100u Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
H D - DTA10 0 u
Quick Start Guide
Cable In
To TV
CH 3/4
Switch
HDMI
Power
The HD-DTA100u
will not turn on
• MakesurethePOWERLEDonthefrontoftheHD‑DTA100u
islitgreen.
• IftheHD‑DTA100uisconnectedtoaswitchedoutlet,make
suretheswitchisturnedon.Itisrecommendedtousean
unswitchedoutlet,ifpossible.
• UnplugtheHD‑DTA100ufromtheACoutlet,andthenplugit
backin.
• MakesuretheremotecontrolisinDTAmode,andturnthe
HD‑DTA100uonbypressingtheDTAbutton.
The remote
control does not
work
• MakesuretheremotecontrolisinDTAmode.
• Makesuretherearenoobstructionsbetweentheremote
controlandtheHD‑DTA100u.Aimtheremotecontroldirectly
attheHD‑DTA100ufrontpanel,nottheTVorVCR.
• TheanglebetweentheremotecontrolandtheHD‑DTA100u
maybetoolarge.StandinfrontoftheHD‑DTA100uandnot
toofartoeitherside.
• Pressandreleaseoperationbuttonsoneatatime,rmlyand
deliberately.
• Checkthebatteriesintheremotecontrol.Installnew
batteriesifneeded.
There is no video
on the TV screen
• MakesuretheTVisonandsettotheappropriateinput
sourcefortheHD‑DTA100u.
• MakesuretheHD‑DTA100uisonandtunedtoanauthorized
cablechannel.
• MakesurethecablesbetweentheHD‑DTA100uandtheTV
arermlyconnected.
• Makesurethecoaxialcablefeedisrmlyconnectedtothe
HD‑DTA100uandthewalljack.
There is no audio
when viewing
cable channels
• PressMUTEontheremotecontroltorestoresound.
No closed
captions display
• MakesureclosedcaptionsareenabledontheTV.(Note:
Closedcaptioningmaynotbeavailableforthecurrent
program.)
Troubleshooting
Checkherebeforecallingyourserviceprovider.
HDTV
HDMI
Coax cable
Power cord
HD-DTA100u
HDTV Electrical OutletCable Outlet
Cable In
+5V DC In
12 3
HDMI
HDMI
MOTOROLAandtheStylizedMLogoaretrademarksorregisteredtrademarksofMotorolaTrademarkHoldings,LLC.HDMI,
theHDMIlogo,andHigh‑DenitionMultimediaInterfacearetrademarksorregisteredtrademarksofHDMILicensing,LLC
intheUnitedStatesand/orothercountries.Allotherproductorservicenamesarethepropertyoftheirrespectiveowners.
Nopartofthispublicationmaybereproducedinanyformorbyanymeansorusedtomakeanyderivativework(suchas
translation,transformation,oradaptation)withoutwrittenpermissionfromMotorolaMobility,LLC.
©2012MotorolaMobility,LLC.Allrightsreserved.
589976‑001‑a09/12
SDTV
Coax cable
HD-DTA100u
SDTV Electrical OutletCable Outlet
Cable In/
RF In
To TVCable In
+5V DC In
12 3
Power cord
Setting Up Your HD-DTA100u and
RF4CE Remote Control
IMPORTANT! Read the enclosed Safety Instructions
before you begin.
1. Connect your cable service.
Connectthecoaxialcablefromyourwalloutlettothe
Cable InportontheHD‑DTA100u.
2. Connect your TV.
Ifyouhaveahigh‑denitionTV,usetheHDMIconnector.
Ifyouhaveastandard‑denitionTV,usetheTo TV
connector.
3. Plug in the HD-DTA100u.
ConnectthepowercordtotheHD‑DTA100u,thenplugit
intoanunswitchedelectricaloutlet.
4. Turn on the TV and select the input.
IfyouhaveanHDTV,usetheremotecontrolforyour
TVtoselecttheHDMIportyouusedtoconnectthe
HD‑ DTA100u.
IfyouhaveanSDTV,tuneyourTVtoChannel3and
settheswitchonthebackoftheHD‑DTA100uto
CH3.Ifyourscreenremainsblack,switchyourTVand
HD‑DTA100utoCH4.
5. Put the batteries in the HD-DTA100u remote
control.
6. Program the RF4CE remote control.
PointtheremotecontrolattheHD‑DTA100u.Pressand
holdtheSETUPbuttonuntiltheLEDontheremote
controlblinkstwice,thenpresstheMenubutton.The
LEDwillblinkcontinuouslyuntiltheremotecontrolis
paired.Followthepairinginstructionsonthescreen.
(Pairinginstructionsarealsoprintedonthebackofthe
remotecontrol.)
/