Siemens LU29050 Owner's manual

Montageanleitung

Installation Instructions

Notice de montage

Montagevoorschriften

Istruzioni di installazione

Instrucciones de montaje

Instruções de montagem

Monteringsanvisning

Asennusohje

Montagevejledning

Ïäçãßåò åãêáôÜóôáóçò

DE

EN

FR

PT

ES

NL

IT

DA

SV

NO

FI

GR

2

de Seite 3-7

en page 8-12

fr page 13-17

nl

pagina

18-22

it

pagina

23-27

es

página

28-32

pt

página

33-37

sv sida 38-42

no side 43-47

fi sivu 48-52

da side 53-57

gr Óåëßäá 58-62

120

598 - 898

500

120

598 - 898

500

Elektrische Kochfelder

Electric cookers

Cuisinières électriques

Elektrisch fornuis

Cucine elettriche

Cocinas electricas

Fogões eléctricos

Elektrisk spis

Elektriske komfyrer

Sähköliesien osalta

Elektriske kogeplader

ÇëåêôñéêÝò êïõæßíåò

> 65 cm

> 50 cm

Gas- oder kombinierte Herde

Gas or mixed cookers

Cuisinières à gaz ou mixtes

Gas- of gemengd fornuis

Cucine a gas o miste

Cocinas a gas o mixtas

Fogões a gás ou mistos

Gasspis eller kombinerad gashäll

Gasskomfyrer og blandede komfyrer

Kaasu- ja sekaliesien osalta

Gasblus og elektriske kogeplader

Êïõæßíåò õãñáåñßïõ Þ ìåéêôÝò

Page is loading ...

8

Installation Instructions:

Important information

Old appliances are not worthless

rubbish.

Valuable raw materials can be reclaimed by

recycling old appliances.

Before disposing of your old appliance,

render it unusable.

This appliance is marked according to the

European directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of

correctly, you will help prevent potential

negative consequences for the environment

and human health, which could otherwise be

caused by inappropriate waste handling of

this product.

The symbol on the product, or on the

documents accompanying the product,

indicates that this appliance may not be

treated as household waste. Instead it

should be taken to the appropriate collection

point for the recycling of electrical and

electronic equipment. Disposal must be

carried out in accordance with local

environmental regulations for waste

disposal.

For more detailed information about

treatment, recovery and recycling of this

product, please contact your local council,

your household waste disposal service or the

shop where you purchased the product.

You received your new appliance in a

protective shipping carton.

All packaging materials are environmentally

friendly and recyclable.

Please contribute to a better environment by

disposing of packaging materials in an

environmentally-friendly manner.

Please ask your dealer or inquire at your

local authority about current means of

disposal.

The extractor hood can be used in

exhaust air or circulating air mode.

Always mount the extractor hood over

the centre of the hob.

The minimum distance between the

supporting surface for the cooking vessels

on the hob and the lowest part of the range

hood must be not less than 50cm from

electric cookers and 65cm from gas or

mixed cookers.

If the instructions for installation for the

gas hob specify a greater distance, this must

be adhered to.

9

Prior to installation

Exhaust-air mode

The exhaust air is discharged upwards

through a ventilation shaft or directly through

the outside wall into the open.

For operating in exhaust-air mode, a one-

way flap should be mounted inside the wall

ventilation box.

If no one-way flap was enclosed with the

hood, it can be obtained from a specialist

retailer.

Installing the one-way flap:

❑ Snap the one-way flap into the air pipe.

The two lightly sprung flaps must be

able to move upwards.

If the exhaust air is going to be

discharged into the open, a telescopic wall

box should be fitted into the outside wall.

❑ For optimum extractor hood efficiency:

❑ Short, smooth air exhaust pipe.

❑ As few bends in the pipe as possible.

❑ Diameter of pipe to be as large as

possible and no tight bends in pipe.

If long, rough exhaust-air pipes, many

pipe bends or smaller pipe diameters

are used, the air extraction rate will no

longer be at an optimum level and

there will be an increase in noise.

❑ Round pipes:

We recommend Internal diameter:

120 mm

❑ Flat ducts must have an internal cross

section that equates to that of round

pipes.

There should be no sharp bends.

Ø 150 mm approx. 177 cm

2

.

❑ If pipes have different diameters:

Insert sealing strip.

❑ For exhaust-air mode, ensure that there

is an adequate supply of fresh air.

Connecting a Ø 150 mm exhaust-air pipe:

❑ Mount the pipe directly onto the air outlet

on the hood.

Circulating-air mode

❑ With activated carbon filter if exhaust-air

mode is not possible.

The complete installation set can be

obtained from specialist outlets.

The corresponding accessory numbers can

be found at the end of these operating

instructions.

10

Electrical connection

The mains power supply must correspond to

the rating indicated on the plate situated

inside the hood. If provided with a plug

connect the hood to a socket in compliance

with current regulations and positioned in an

accessible area. If it not fitted with a plug

(direct mains connection) or if the plug is not

located in an accessible area apply a bi-

polar switch in accordance with standards

which assures the complete disconnection of

the mains under conditions relating to over-

current category III, in accordance with

installation instructions.

Warning! Before re-connecting the hood

circuit to the mains supply and checking the

efficient function, always check that the

mains cable is correctly assembled.

Warning! Power cable replacement must be

undertaken by the authorized service

assistance centre or similar qualified person.

Connect the hood to a norm complying plug

only. The plug should be located in an

accessible zone.

❑ The plug must be equipped with a

protection circuit.

❑ If after installation the plug can not be

reached, a disconnecting device must be

envisaged.

Fixed installation:

The fixed installation can be carried out by a

qualified and authorized person only.

Envisage an omnipolar switch having a

contact opening of at least 3mm, including

an automatic circuit breaker.

The cable must be replaced by the

manufacturer, the assistance centre or a

qualified and authorized person only, in

order to avoid any dangers.

Electrical data:

The technical data of the device are on the

distinctive label inside the device behind the

grease filters.

In case of repair, disconnect the electric

supply from the cooker hood.

Length of the feeding cable: 1,30m.

The hood complies with the EMC directives.

11

Installation

WARNING! Do not connect the appliance to the mains until the installation is fully

complete.

To the wall

With 4 screws.

g. 6

1

2

3

2

3

1. Mark mounting boreholes.

Dimensions can be found in or use

template.

2. Drill 8 mm dia. holes and insert wall

plugs flush with the wall.

3. Screw in the upper screws (on left and

right) until there is a gap of approx.

7 mm between the screw head and the

wall.

❑ Remove the grease filters (see

Instructions for use).

In circulating-air mode,

apply the plug supplied

to close the exhaust

hole.

To a wall-hanging cupboard

With 4 screws.

1. Dimensions for the mounting boreholes

can be found in, or place a template on

the base of the wallhanging cupboard.

2. Mark the mounting holes and make pilot

holes with a bradawl.

In exhaust-air mode (upwards) mark the

exhaust-air opening and saw out.

In circulating-air mode,

apply the plug supplied

to close the exhaust

hole.

❑ Consider the location of the connection

cable; if required, saw out the cupboard.

3. Remove the filter grille (see Instructions

for use).

4. Screw the extractor hood to the base of

the cupboard.

1

2

1

2

12

4

4. Secure the nuts inside the box of the

hood on the square slots and screw in,

from outside, the metric screws supplied

to their maximum.

7 mm

5

6

7

5. Hook the hood to the upper screws.

6. Adjust the structure of the hood.

7. Insert and totally screw the screws in the

lower holes for the final fixing.

❑ Reinstall the grease filters (see

Instructions for use)

Installation Final assembly

Selecting the operating mode:

A

F

❑ Exhaust-air mode: Position A

A

F

❑ Circulating-air mode: Position F

❑ Refit the grease filter.

❑ Connect to the power supply.

Page is loading ...

Siemens LU29050 Owner's manual

Siemens LU29050 Owner's manual

in other languages

Related papers

Other documents