OWNER’S MANUAL
DVD MINI HI-FI SYSTEM
Please read this manual carefully before operating
your set and retain it for future reference.
DM5430 (DM5430, DMS5430V)
DM5330 (DM5330, DMS5330V)
DM5230 (DM5230, DMS5230V)
ENGLISH РУССКИЙ
FRANÇAIS
DM5330-AU_BUZBLLK_ENG.indd 1 2013-07-04 1:30:12
DM5330-AU_BUZBLLK_ENG.indd 2 2013-07-04 1:30:13
1 Getting Started
Getting Started 3
Getting Started
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure that
may be of sucient magnitude to
constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specied herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not
try to open the enclosure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specication page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or re. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
DM5330-AU_BUZBLLK_ENG.indd 3 2013-07-04 1:30:16
Getting Started4
Getting Started
1
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or
the local authorities.
3. The correct disposal of your
old appliance will help prevent
potential negative consequences
for the environment and human
health.
4. For more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled
bin symbol is attached to batteries/
accumulators of Your product
it means they are covered by
European Directive 2006/66/EC.
2. This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the
battery Contains more that 0.0005%
of mercury,0.002% of cadmium or
0.004% of lead.
3. All batteries/accumulators should
be disposed separately from
the municipal waste stream via
designated collection facilities
appointed by the government or
the local authorities.
4. The correct disposal of Your old
batteries/accumulators will help
to prevent potential negative
consequences for the environment,
animal and human health.
5. For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your
city office, waste disposal service or
the shop where You purchased the
product.
DM5330-AU_BUZBLLK_ENG.indd 4 2013-07-04 1:30:17
Getting Started 5
Getting Started
1
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, re or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, shall be placed on the
apparatus.
Notes on Copyrights
y
This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
y
Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/
or criminal liability.
DM5330-AU_BUZBLLK_ENG.indd 5 2013-07-04 1:30:17
Table of Contents6
Table of Contents
1 Getting Started
3 Safety Information
8 Unique Features
8 Accessories
8 Introduction
8 – Playable Discs
8 – About the
& Symbol Display
9 – Symbol Used in this Manual
9 – Regional Codes
9 Playable file Requirement
9 – MP3/WMA music file requirement
9 – Compatible USB Devices
10 – USB device requirement
10 – Photo file requirement
10 – DivX file requirement
11 Remote control
12 Front panel
14 Rear panel
2 Connecting
15 Connecting to speakers
15 – Attaching the speakers to the unit
15 Antenna Connection
16 Connections to Your TV
16 – Video Connection
17 – Component Video Connection
17 Optional Equipment Connection
17 – AUX In Connection
18 – USB Connection
19 Adjust the Setup settings
19 – OSD Initial language settings -
Optional
19 – To display and exit the Setup Menu
3 System setting
20 – LANGUAGE
20 – DISPLAY
21 – AUDIO
21 – LOCK (Parental Control)
22 – OTHERS
DM5330-AU_BUZBLLK_ENG.indd 6 2013-07-04 1:30:17
Table of Contents 7
1
2
3
4
5
6
4 Operating
23 Basic Operations
23 – Disc/USB Operations
24 Other Operations
24 – Displaying Disc Information on-screen
24 – To display the DVD Menu
24 – To display the DVD title
24 – Selecting a subtitle language
24 – 1.5 times speed playback
25 – Starting play from selected
time
25 – Last Scene Memory
25 – Changing the character set to display
DivX® subtitle correctly - optional
25 – Creating your own program
25 – Viewing a PHOTO file
26 – Viewing a PHOTO file as a slide show
26 – Setting the Clock
26 – Using your player as an alarm clock
27 – Sleep Timer Setting
27 – Dimmer
27 – DEMO
27 – Turning off the sound temporarily
27 – Screen Saver
27 – System Select - Optional
27 – Displaying file information
(ID3 TAG)
28 – Using Microphone
28 – VOCAL FADER
29 Radio Operations
29 – Listening to the radio
29 – Presetting the Radio Stations
29 – Deleting all the saved stations
29 – Improving poor FM reception
30 Sound adjustment
30 – Setting the surround mode
30 – Setting the USER EQ
31 Advanced Operations
31 – Listening to music from your external
device
31 – Recording to USB
5 Troubleshooting
32 Troubleshooting
6 Appendix
33 Specifications
35 Maintenance
35 – Handling the Unit
35 – Notes on Discs
35 Trademarks and Licenses
36 Language Codes
37 Area Codes
DM5330-AU_BUZBLLK_ENG.indd 7 2013-07-04 1:30:18
Getting Started8
Getting Started
1
Unique Features
USB Direct Recording
Records music to your USB device.
Accessories
Please check and identify the supplied accessories.
AM antenna (1) FM antenna (1)
Remote control (1) Battery (1)
Introduction
Playable Discs
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG les. Some DVD±RW/DVD±R or CD-RW/
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc,
or the characteristics of the recording device and
authoring software.
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and nalized only
DVD-RW (8 cm / 12 cm disc)
Video mode and nalized only
DVD+R: Video mode only
Supports the double layer disc also
DVD+RW (8 cm / 12 cm disc)
Video mode and nalized only
Audio CD: Music CDs or CD-R/CD-
RW in music CD format that can be
purchased.
About the
&
Symbol Display
“
&
” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that disc.
DM5330-AU_BUZBLLK_ENG.indd 8 2013-07-04 1:30:21
Getting Started 9
Getting Started
1
Symbol Used in this Manual
DVD and nalized DVD±R/RW
r
DivX les
y
MP3/WMA les, Audio CDs
u
JPG les
i
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labelled
same as the rear of the unit or “ALL”.
y
Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
y
If you try to play a DVD with a dierent regional
code from your unit, the message “Check
Regional Code” appears on the TV screen.
,
Note
Indicates special notes and operating features.
>
Caution
Indicates cautions for preventing possible damages
from abuse.
Playable file
Requirement
MP3/WMA music file
requirement
MP3/ WMA le compatibility with this unit is limited
as follows :
y
Sampling Frequency : 32 - 48 kHz (MP3), 32 - 48
kHz (WMA)
y
Bit rate : 32 - 320 kbps (MP3), 40 - 192 kbps
(WMA)
y
Maximum les : Under 999
y
File extensions : “.mp3”/ “.wma”
y
CD-ROM le format : ISO9660/ JOLIET
y
We recommend that you use “Easy-CD Creator”,
which creates an ISO 9660 le system.
y
You have to set the disc format option to
[Mastered] in order to make the discs compatible
with the LG players when formatting rewritable
discs. When setting the option to Live File
System, you cannot use it on LG players.
(Mastered/ Live File System : Disc format system
for Windows Vista)
Compatible USB Devices
y
MP3 Player : Flash type MP3 player.
y
USB Flash Drive : Devices that support USB2.0 or
USB1.1.
y
The USB function of this unit does not support
all USB devices.
DM5330-AU_BUZBLLK_ENG.indd 9 2013-07-04 1:30:22
Getting Started10
Getting Started
1
USB device requirement
y
Devices which require additional program
installation when you have connected it to a
computer, are not supported.
y
Do not extract the USB device while in operation.
y
For a large capacity USB, it may take longer than
a few minute to be searched.
y
To prevent data loss, back up all data.
y
If you use a USB extension cable or USB hub, the
USB device is not recognized.
y
Using NTFS le system is not supported. (Only
FAT(16/ 32) le system is supported.)
y
This unit is not supported when the total
number of les is 1 000 or more.
y
External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
y
USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
Photo file requirement
Photo le compatibility with this unit is limited as
follows :
y
Max pixel in width :
Normal : 5120 x 3840
Progressive JPEG : 2048 x 1536
y
Maximum les : Under 999
y
Some discs may not operate due to a dierent
recording format or the condition of disc.
y
File extensions : “.jpg”
y
CD-ROM le format : ISO9660 LEVEL 1/ JOLIET
DivX file requirement
DivX le compatibility with this unit is limited as
follows :
y
Available resolution:
up to 800 x 600 (W x H) pixels.
y
The le name of the DivX subtitle should be
entered 45 characters or less.
y
If there is a code impossible to express in the
DivX le, it may be displayed as a “ _ “ mark on
the display.
y
Frame rate : less than 30 fps.
y
If the video and audio structure of recorded
les are not interleaved, either video or audio is
output.
y
Playable DivX le : “.avi”, “.mpg”, “.mpeg”, “.divx”
y
Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
y
Playable Codec format :
“DIVX3.11”, “DIVX4”, “DIVX5”,
“MP4V3”, “3IVX”.
y
Playable Audio format : “AC3”, “PCM”, “MP3”, “WMA”.
y
Sampling frequency : between 32 to 48 kHz
(MP3), between 32 to 48 kHz (WMA)
y
Bit rate : between 32 to 320 kbps (MP3), 40 to
192 kbps (WMA)
y
For Discs formatted in Live le system, you can
not use it on this unit.
y
If the name of movie le is dierent from that of
the subtitle le, during playback of a DivX le,
subtitle may not be display.
y
If you play a DivX le dier from DivX spec, it
may not operate normally.
DM5330-AU_BUZBLLK_ENG.indd 10 2013-07-04 1:30:22
Getting Started 11
Getting Started
1
Remote
control
Battery Installation
Remove the battery cover on
the rear of the Remote Control,
and insert one (size AAA)
battery with
4
and
5
matched
correctly.
• • • • • •
a
• • • • •
FUNCTION : Selects the
function and input source.
SLEEP : Sets the system to turn
o automatically at a specied
time.
POWER (
1
) : Switches the unit
ON or OFF.
OPEN/CLOSE (
B
) : Opens and
closes the disc tray.
TITLE : If the current DVD
title has a menu, the title
menu appears on the screen.
Otherwise, the disc menu may
appear.
DISPLAY : Accesses On-Screen
Display.
MENU : Accesses the menu on a
DVD disc.
SETUP : Accesses or removes
setup menu.
• • • • • •
b
• • • • •
PRESET (
W/S
) : Selects
programme of Radio.
TUN. -/+(
A/D
) : Tunes in the
desired radio station.
W/S/A/D
(up/ down/ left/
right) : Used to navigate on-
screen displays.
ENTER (
b
) : Acknowledges
menu selection.
RETURN (
x
) : Moving back
wards in the menu.
REC (
X
) : Recording.
• • • • • •
c
• • • • •
STOP (
Z
) : Stops playback or
recording.
PLAY (
d
), MO./ST. : Starts
playback.
Selects Mono/ Stereo.
PAUSE/STEP (
M
) : Pauses
playback.
SKIP (
C/V
) : Goes to next
or previous chapter/ track/ le.
SCAN (
c/v
) : Searches
backward or forward.
D.SKIP : Chooses a desired disc.
MUTE : Mutes the sound.
VOL (+/-) (Volume) : Volume
control.
EQ (
$
) : You can choose sound
impressions.
LG EQ (
9
) : Select a Natural or
Local Specialization equalizer
eect by LG EQ.
• • • • • •
d
• • • • •
0 to 9 numerical buttons :
Selects numbered options in a
menu.
REPEAT/RANDOM : Selects a
play mode.
SUBTITLE (
]
) : During
playback, press SUBTITLE (
]
)
repeatedly to select a desired
subtitle language.
TV Control buttons : Controls
the TV. (LG TV only)
Controlling the TV.
You can control the sound
level, input source, and power
switching of LG TVs as well.
Hold POWER (TV) and press
PR/CH (+/–) button repeatedly
until the TV turns on or o.
PROG./MEMO. : Accesses
Program menu.
CLEAR : Removes a track
number on the Program List.
MIC VOL (+/ - ) : Adjusts
microphone volume.
ECHO VOL (+/ - ) : Adjusts echo
volume.
VOCAL FADER : You can enjoy
the function as karaoke, by
reducing singer vocal of music
in the various source.
DM5330-AU_BUZBLLK_ENG.indd 11 2013-07-04 1:30:24
Getting Started12
Getting Started
1
Front panel
DM5330-AU_BUZBLLK_ENG.indd 12 2013-07-04 1:30:25
Getting Started 13
Getting Started
1
a
Disc tray
b
1
/
!
STANDBY/ON
c
Display window
d
CLOCK
For setting the clock and checking the time.
e
TIMER
With the TIMER function you can turn USB, CD
play and TUNER reception on or o at a desired
time.
f
USER EQ
g
Selects DVD/CD function.
Selects TUNER function.
Selects USB function.
Selects AUX function.
h
SET
Conrms the settings. (TIMER/ CLOCK)
CD
M
Pauses.
PRESET (-)
TUNING (-)
DEMO In power o state to demonstrate the
function on display window. To cancel it, press
1
/
!
or this button again.
i
Headphone jack
j
USB connector
k
B
OPEN/CLOSE
l
DISC SKIP
Choose a desired disc.
m
EQ
You can choose xed sound impression.
n
BASS BLAST
Extreme Dynamic Sound System.
Reinforce the treble, bass and surround eect.
MP3 OPT.
Optimizes compressible MP3 les so that it
improves the bass sound.
o
REC.
p
LG EQ
You can choose xed sound impression.
q D
PRESET (+)
TUNING(+)
I
(STOP)
r
MIC VOL.
Adjust microphone volume.
s
MIC 1, 2
t
Volume control
DM5330-AU_BUZBLLK_ENG.indd 13 2013-07-04 1:30:26
Getting Started14
Getting Started
1
Rear panel
a
AUX IN connector
b
VIDEO OUT connector
c
ANTENNA (FM, AM)
d
COMPONENT VIDEO OUT (PROGRESSIVE SCAN) connector
e
POWER IN
f
SPEAKERS terminals
g
Cooling Fan (Except DM5230)
DM5330-AU_BUZBLLK_ENG.indd 14 2013-07-04 1:30:27
2 Connecting
Connecting 15
Connecting
2
Connecting to
speakers
Attaching the speakers to the
unit
To connect the cable to the unit, press each plastic
nger pad to open the connection terminals on the
unit. Insert the wire and release the nger pad.
Connect the black stripe of each wire to the
terminals marked - (minus) and the other end to
the terminals marked + (plus).
The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
>
Caution
Antenna Connection
Connect the supplied FM/ AM antenna for listening
to the radio.
y
To prevent noise pickup, keep the AM Loop
antenna away from the unit and other
components.
y
Be sure to fully extend the FM wire antenna.
,
Note
DM5330-AU_BUZBLLK_ENG.indd 15 2013-07-04 1:30:29
Connecting16
Connecting
2
Connections to Your
TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
y
Depending on your TV and other equipment
you wish to connect, there are various ways
you could connect the unit. Use only one of
the connections described in this manual.
y
Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
y
Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel.
y
Do not connect your unit via your VCR.
The image could be distorted by the copy
protection system.
,
Note
Video Connection
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
Yellow
TV
DM5330-AU_BUZBLLK_ENG.indd 16 2013-07-04 1:30:30
Connecting 17
Connecting
2
Component Video Connection
Connect the COMPONENT VIDEO OUT
(PROGRESSIVE SCAN) jacks on the unit to the
corresponding input jacks on the TV using
component cables.
You can hear the sound through the system’s
speakers.
Green
Blue
Red
If your TV accepts progressive format signals,
you must use this connection and set
[Progressive Scan] in [Display] setup to [On]
(See page 20).
,
Note
Optional Equipment
Connection
AUX In Connection
Connect an Output of auxiliary device to the AUX
(L/R) IN Connector.
Red
White
To the audio output jacks
of your component
(TV, VCR, etc.)
If your TV has only one output for audio
(mono), connect it to the left (white) audio jack
on the unit.
,
Note
TV
DM5330-AU_BUZBLLK_ENG.indd 17 2013-07-04 1:30:31
Connecting18
Connecting
2
USB Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Removing the USB Device from the unit
1. Choose a different function/mode or
press STOP (
Z
) twice in a row.
2. Remove the USB device from the unit.
,
Note
DM5330-AU_BUZBLLK_ENG.indd 18 2013-07-04 1:30:32
3 System setting
System setting 19
System setting
3
Adjust the Setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and
the Setup menu, among other things. For details on
each Setup menu item.
OSD Initial language settings
- Optional
When using this unit for the rst time, the initial
language setup menu appears on your TV screen.
You must complete initial language selection
before using the unit. English will be selected as the
initial language.
1. Press POWER (
1
) to turn the unit on.
The language setup menu will appear on the
screen.
2. Use
W/S/A/D
to select a language then
press ENTER (
b
).
The confirm menu will appear.
3. Use
A/D
to select [Enter] then press
ENTER (
b
) to finish the language setup.
To display and exit the Setup
Menu
1. Select the DVD/CD or USB function by pressing
FUNCTION.
2. Press SETUP.
Displays the [SETUP] Menu.
3. Press SETUP or RETURN (
x
) to exit in the
[SETUP] Menu.
About help menu for Setup
Menu Buttons Operation
w/s
Move
W/S
Moving to another
menu.
a
Prev.
A
Moving to previous
level.
d
Select
D
Moving to next level
or selecting menu.
x
Close
RETURN
To exit the [Setup]
menu.
b
Enter
ENTER To conrm menu.
DM5330-AU_BUZBLLK_ENG.indd 19 2013-07-04 1:30:32
System setting20
System setting
3
LANGUAGE
OSD
Select a language for the Setup menu and then on
screen display.
Disc Audio/Disc Subtitle/Disc Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the disc
was recorded.
[Other]
To select another language, press numeric
buttons and then ENTER (
b
) to enter the
corresponding 4-digit number according to the
language code list on the page 36. If you enter
the wrong language code, press CLEAR.
[O (for Disc Subtitle)]
Turn o Subtitle.
DISPLAY
TV Aspect
Select which screen aspect to use based on the
shape of your TV screen.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
[Letterbox]
This displays a wide screen picture with black
bands at the top and bottom of the screen.
[Panscan]
This lls the entire 4:3 screen, cropping the
picture as necessary.
Progressive Scan
(For Component Video connections)
Selects whether the COMPONENT
VIDEO(PROGRESSIVE SCAN) OUT jacks output
progressive signal. If your TV accepts progressive
format signals, you will enjoy accurate color
reproduction and high quality image by selecting
[On]. If your TV does not accept progressive format
signals, select [O ].
If you set Progressive Scan to [On] in error, you
must reset the unit. First, remove the disc from the
unit. Next, press and hold STOP (
Z
) for about ve
seconds. The video output will be restored to the
standard setting, and a picture will be visible on
your TV.
DM5330-AU_BUZBLLK_ENG.indd 20 2013-07-04 1:30:32
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI