AL-KO Garden Pump Jet 601 3.100 L/h User manual

JET 601 / 802

JET 601 INOX / JET 802 INOX

JET 1002 INOX

INfOrmaTION I maNuals I sErvIcE

QUALITY FOR LIFE

Garden + Hobby

467 353_b I 08/2010

GB

f

I

slO

DK

Pl

sK

D

NlE

H

Hr

s

fIN cZ

rus

ua

P

Tr

Page is loading ...

Introduction

Please read the operating instructions carefully

before you use the garden pump to prevent

accidents and ensure the trouble-free operation

of the pump.

Make sure you keep the instructions at hand for

quick reference. If you resell your pump or give it

to another user, please include these instructions

in the sale or the gift.

The following symbols are used in the instruc-

tions:

DANGER

This symbol draws your attention to work

processes or operating procedures that

have to be carefully observed in order to

prevent serious injury to the user or an-

other person.

CAUTION

This symbol draws your attention to infor-

mation you need to ensure that your

system is not damaged due to improper or

careless use.

PLEASE NOTE

The information symbol draws your atten-

tion to essential technical requirements.

For your safety

The garden pump may only be connected

to an electrical device which is compliant

with DIN/VDE 0100, Parts 737, 738 and

702 (swimming pools). Make sure that fuse

protection in the form of a 10 A automatic

cut-out and a fault current guard circuit

with a nominal fault current of 10/30 mA is

installed.

The supply voltage and current specified

on the type plate must be identical with the

voltage and current of your electrical

system.

If you need to connect your pump to an

extension cord, make sure that the cable is

3 x 1.5 mm

2

, that it corresponds to type

H07RN-F and is compliant with DIN

57282/57245. The connector must be

splash-proof. Cable drums must be com-

pletely unwound.

The garden pump may not operated by

anyone who has not read or does not fully

understand the operating instructions or is

under the age of 16.

The garden pump may not be used for any

other than its designated use. Before

putting the system into operation, make

sure that the garden pump, the electric

cable and the plug are not worn or dam-

aged and the garden pump is not exposed

to water jets or is operated in the rain.

Do not operate the garden pump if it is

damaged. Necessary repairs must be

carried out in a qualified AL-KO service

centre.

Never use the electric cable to lift, carry or

attach the garden pump to another object.

Do not pull on the cable when unplugging

the pump.

Make sure that the pump is unplugged

before beginning any maintenance, repair

or cleaning work. In the event of a malfunc-

tion, immediately unplug the pump. Make

sure that the plug does not get wet.

Do not attempt to make any changes or

modifications to the garden pump by

yourself. You may endanger your life or

invalidate the warranty.

Make sure that the garden pump is placed

securely onto a flat surface when in opera-

tion so that it cannot tip over.

Risk of injury due to hot water!

The water in the pump can heat up signifi-

cantly, during longer periods of operation

(>10 min) against closed outlet side.

This hazard can occur due to:

− side under compression closed

− water shortage in the suction line

− improper installation

− faulty pressure switch

In this case:

− isolate the pump from the mains

− allow the pump and water to cool down

− check water level on inlet side

− check lines for tightness

− check installation

− check pressure switch

− only restart pump after rectifying the

cause of the fault

GB 1

Use

GB 2

Designated use

The garden pump is designed for home use in

your house or garden. Please observe the tech-

nical data given in the instructions before putting

the pump into operation.

Your garden pump has been designed for use in

the following applications:

– irrigation and watering, e.g. of your lawn or

flower and vegetable gardens,

– emptying containers or pumping liquid from

one container into another (e.g. swimming

pools),

– pumping water from wells, rain drums or

cisterns.

The system is designed to pump only the follow-

ing liquids:

– clear water,

– rain water,

– chlorine water (pool water).

Prohibited use

Your garden pump is not intended for permanent

operation. The pump may not be used to pump

the following liquids:

– drinking water

– saltwater,

– beverages or liquid foods,

– corrosives or chemicals,

– acids or combustible, explosive or gas-

forming liquids,

– liquids with a temperature above 35 °C,

– sandy water or water containing abrasives.

Description of the pump

Garden pump/accessories (Figs. A, B,C)

1 Pump inlet/suction hose connector

2 Filler screw

3 Pump outlet/pressure hose connector

4 Motor housing

5 Electric cable

6 On/Off switch

7 Suction body

8 Pump chamber

9 Draining screw

10 Elbow nipple with washer (accessories)

11 Threaded connector (accessories)

12 AL-KO suction kit (accessories)

13 Filter (accessories)

Function

The garden pump sucks the liquid to be pumped

into the pump through the suction hose (1) and

pumps it out at the outlet (3).

Use the On/Off switch (6) to switch the garden

pump on or off as desired.

Thermal protection

Your pump is equipped with a thermal protection

switch, which switches the pump off if it over-

heats. The pump will remain off until it has

cooled down. After about 15 - 20 minutes, the

pump will automatically switch on.

Setting up and operating the sys-

tem

• Place the garden pump onto a hard, flat

surface so that it cannot tip over and so that

it will not be near the flow of water.

• Make sure that the pump is protected from

rain and any direct exposure to water.

Attaching the suction hose

Choose a hose which is long enough so

that the pump will not suck in air and run

dry. The hose should be at least 30 cm

under the surface of the liquid to be

pumped while the pump is in operation.

• Attach the suction hose. Make sure to screw

it in tightly, but take care not to damage the

threads.

If the liquid to be pumped is deeper than 4

m, you should use a suction hose which is

larger than 1“ in diameter for the best

performance. We recommend our AL-KO

suction set (12), which consists of a

suction hose, strainer and non-return

valve. The suction set is available at your

local retailer’s.

Before pumping sandy water, you must

insert a filter (13) between the suction hose

and the pump inlet or you will dam- age

your garden pump. The filter is available at

your local retailer’s.

• When laying the suction hose, make sure

that it is lower than the pump.

If the suction hose is laid so that it is higher

than the pump, bubbles will be- come

trapped in the line and the pump will suck

air.

Cleaning the pump

• Fill the suction hose.

If you have used your garden pump to pump

chlorine water (swimming pool water) or liquids

which leave a residue, flush your pump out with

clear water after use.

Attaching the pressure hose

• Screw the threaded connector (11) into the

pump outlet (3).

• Attach the elbow nipple (10) to the connector

and turn the nipple so that it points in the de-

sired direction.

Clearing blockages

If your garden pump should become blocked so

that it does not suction or pump out liquid, re-

move the obstruction as follows:

• Attach a hose to the elbow nipple. The nipple

can be cut to fit the size of the hose used.

• Clear the pressure line (open valves, spray-

ers, etc.).

• Remove the suction hose from the pump

inlet (1).

• Attach the pressure hose to the water tap

and spray water into the pump chamber until

the blockage is flushed out.

Filling the garden pump

Before putting your garden pump into

operation, you must fill it with water until it

overflows to achieve full suction power. Do

not operate the pump while it is dry be-

cause this will cause serious damage to

the pump.

• Check to see that the obstruction has been

cleared entirely by switching on the pump for

a short time. Do not let the pump suck air.

• If the pump runs trouble-free, put it into ope-

ration as described in the instructions.

• Remove the filler screw (2).

Frost protection

• Pour water into the opening until the cham-

ber of the pump (8) is full.

Store your pump so that it is protected from frost.

Remember to empty it of any remaining liquid

before storing it by removing the filler screw (9)

and dumping out any water.

• Replace the filler screw (2) and tighten it.

Switching the pump on and off

• Plug the electric cable into the socket.

RL 2002/96 EG

Do not dispose of worn-out

units through the household

garbage!

The appliance, its packaging and

accessories are all produced from

recyclable materials and must be

disposed of accordingly.

Make sure that the pump does not run on a

blocked or closed pressure hose.

• Clear the pressure line (open valves, spray-

ers, etc.).

• Switch the pump on by pushing the switch

(6) to On.

• Switch the pump off by pushing the switch

(6) to Off.

Switching off the system

• Switch the system off by unplugging the

electric cable from the socket.

Maintenance and Cleaning

Before beginning any maintenance or

cleaning work, make sure that the garden

pump has been unplugged and take

precautions to ensure that it cannot be

switched on during work!

GB 3

Malfunctions

Before you attempt to remedy any malfunction of your pump, pull the plug to prevent injury or

death due to electrocution!

What is wrong?

What is the possible reason?

How to remedy the malfunction:

Motor does not run. Impeller is blocked.

Remove blockage in inlet area. Clean

the impeller with a jet of water.

Thermal switch has switched off. Wait until the thermal switch has

automatically switched the pump on

again. Check the temperature of the

liquid. Have the pump checked.

No power. Check the fuses. Have a qualified

electrician check the power supply.

Garden pump runs

but is not pumping out

liquid.

Water level too low. Lower the hose further underwater.

Air is trapped in the pump chamber. Fill the pump chamber with water.

Suction hose is blocked. DANGER!

Risk of injury due to hot water!

Clear blockage in suction hose.

Pressure line is blocked. DANGER!

Risk of injury due to hot water!

Clear blockage in pressure line.

Pressure hose is bent. Straighten out pressure hose.

Garden pump is only

pumping out liquid

very slowly or weakly.

Pressure hose is bent. Straighten out pressure hose.

Hose diameter is too small.

Pump sucks air

Attach a hose with a larger diameter.

Check all connections and the cover

for tightness

Suction hose is blocked. Clear blockage in suction hose.

Pumping height is too great.

Lower pumping height (see technical

data).

Suction height is too great.

Lower suction height (see technical

data).

If you are unable to remedy a malfunction, please call the AL-KO service centre nearest you.

GB 4

Page is loading ...

GB

2

EC declaration of conformity

We hereby declare that this product, in the form in which it is marketed,

meets the requirements of the harmonised EU guidelines,

EU safety standards, and the product-specic standards.

Product

Garden pump, electric

Serial number

G3013015

Manufacturer

AL-KO Geräte GmbH

Ichenhauser Str. 14

89359 KOETZ

DEUTSCHLAND

Executive Ofcer

Anton Eberle

Ichenhauser Str. 14

89359 KOETZ

DEUTSCHLAND

Model

JET601, JET601 INOX

JET802, JET802 INOX

JET1002 INOX

EU directives

2006/95/EG

2004/108/EG

2000/14/EG (13)

Harmonised standards

EN 60335-1; VDE 0700-1:2007-02

EN 60335-2-41; VDE 0700-41:2004-12

EN 60335-2-41/A2; VDE 0700-41/A2:2009-02

EN 55014-1; VDE 0875-14-1:2007-06

EN 55014-1/A1; VDE 0875-14-1/A1:2008-12

EN 55014-2; VDE 0875-14-2:2009-06

EN 61000-3-2; VDE 0838-2:2006-10

EN 61000-3-2/A1; VDE 0838-2/A1:2007-05

EN 61000-3-2/A7; VDE0838-2/A7:2007-06

EN 61000-3-2/A4; VDE 0838-2/A4:2007-06

EN 61000-3-3; VDE 0838-3:2009-06

Sound power level

measured / guaranteed

JET601, JET601 INOX 74/76 dB(A)

JET802, JET802 INOX 74/77 dB(A)

JET1002 INOX 83/86 dB(A)

Conformity evaluation

2000/14/EG

Appendix V

Kötz, 2010-08-30

Antonio De Filippo, Managing Director

Warranty

If any material or manufacturing defects are found during the statutory customer protection period, we will either repair or

replace the equipment, whichever we consider the more appropriate. This statutory period may vary according to the legisla-

tion in force in the country where the equipment was purchased.

Our warranty is valid only if: The warranty is no longer valid if:

 The equipment has been used properly

 The operating instructions have been followed

 Genuine replacement parts have been used

 The equipment has been tampered with

 Technical modications have been made

 The trimmer was not used for its intended purpose (for exa-

mple, used for commercial or communal applications)

The following are not covered by warranty:

 Paint damage due to normal wear

 Wear parts identied by a border XXX

XXX

(X) on the spare parts list

 Combustion motors – these are covered by a separate warranty from the manufacturer concerned

To make a claim under warranty, please take this statement of warranty and proof of purchase to the nearest authorised

customer service centre. This warranty does not affect the usual statutory rights of the customer relative to the seller.

┌──────┐

└──────┘

Page is loading ...

AL-KO Geraete GmbH l Head Quarter l Ichenhauser Str. 14 l 89359 Koetz l Deutschland

Telefon: (+49)8221/203-0 l Telefax: (+49)82 21/ 203 -138 l www.al-ko.com

Country Company Telephone Fax

A AL-KO Kober Ges.m.b.H. (+43) 35 78 / 2 5152 27 (+4 3) 35 78 / 25 15 3 8

AUS AL-KO International PTY. LTD (+61) 3 / 97 67- 3700 (+61)3 / 97 67-3799

B / L Eurogarden NV (+32) 16 / 80 54 27 (+32) 16 /80 54 25

BG Valerii S&M Group SJ (+359) 2 942 34 02 (+359) 2 942 34 10

CH AL-KO Kober AG (+41) 56 / 4 18 3150 (+ 41) 56 / 4 18 31 60

CZ AL-KO Kober Spol.sr.o. (+420) 3 82 / 2103 81 (+420)3 82 / 212782

D AL-KO Geräte GmbH (+49) 82 21/ 2 03 - 0 (+49) 82 21/ 2 03 -138

DK AL-KO Ginge A/S (+45) 98 82 10 00 (+45)98825454

EST/LT/LV AL-KO Kober SIA (+371) 67409330 (+371) 67807018

F AL-KO S.A.S. (+33)3/85-763540 (+33)3/85-763588

GB Rochford Garden Machinery Ltd. (+44) 19 63 / 82 80 50 (+ 44) 19 6 3 / 82 80 52

H AL-KO KFT (+36) 29 / 53 70 50 (+36)29/537051

HR Brun.ko.-prom d.o.o. (+385)1 3096 567 (+385)1 3096 567

I AL-KO Kober GmbH / SRL (+39)039/9329311 (+39)039/9329390

IN AGRO-COMMERCIAL (+91) 3322874206 (+91)3322874139

IQ Gulistan Com (+946) 750 450 80 64

IRL Cyril Johnston & Co. Ltd. (+44) 2890813121 (+44)2890914220

LY ASHOFAN FOR AGRICULT. ACC. (+218)512660209 (+218)512660209

MA BADRA Sarl (+212)022447128 (+212)022447130

MK Techno Geneks (+389) 2 2551801 (+389) 2 2520175

N AL-KO GINGE A/S (+47)64862550 (+47)64862554

NL O.DE LEEUW GROENTECHNIEK (+31)38/ 444 6160 (+31)38/ 444 6358

PL AL-KO Kober z.o.o. (+48) 61 / 8 16 19 25 (+48)61/81619 80

RO OMNITECH Technology SRL (+4) 021 326 36 72 (+4) 021 326 36 79

RUS OOO AL-KO Kober (+7 ) 499/ 168 87 18 (+7) 499/96600-00

RUS AL-KO St. Petersburg GmbH (+7) 8 12 / 4 46 10 75 (+7 ) 8 12 / 4 4 6 10 75

S AL-KO Ginge Svenska AB (+46)(0)31573580 (+46) (0) 3157 56 20

SK AL-KO Kober Slovakia Spol.s.r.o. (+421) 2 / 45 99 4112 (+4 21) 2 / 4 5 6 4 81 17

SLO DARKO OPARA S.P. (+386) 17225858 (+386)17225851

SRB Agromarket doo (+381)34/30800 (+381)34/30816

TR ZIMAS A.S. (+90) 232 4580586 (+90) 232 4572697

UA TOV AL-KO Kober (+380) 44 / 4 92 33 96 (+380) 44 / 4 92 33 97

AL-KO Garden Pump Jet 601 3.100 L/h User manual

AL-KO Garden Pump Jet 601 3.100 L/h User manual

in other languages

Related papers

Other documents