Digital Watchdog Snapit DWC-V4382TIR User manual

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for future reference.

Vandal-Proof Dome Camera

DWC-V4382D

DWC-V4382TIR

DWC-V4382TIRH

12132012

2

PRECAUTIONS

FCC COMPLIANCE

Do not open or modify.

Do not open the case except during maintenence and installation, for it may be dangerous and can

cause damages.

Do not put objects into the unit.

Keep metal objects and flammable substances from entering the camera.

It can cause fire, short-circuits, or other damages.

Be careful when handling the unit.

To prevent damages, do not drop the camera or subject it to shock or vibration.

Do not install near electric or magnetic fields.

Protect from humidity and dust.

Protect from high temperature.

Be careful when installing near the ceiling of kitchen or a boiler room, as the temperature may rise

to high levels.

Cleaning:

To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.

Mounting Surface:

The material of the mounting surface must be strong enough to support the camera.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference, when the equipment is operated in a residential environment. This equipment

generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance

with the instruction manual, it may cause harmful interference to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

TABLE OF CONTENTS

3

Introduction

Installation

Camera OSD Menu and Glossary

Troubleshooting

Warranty Information

Specifications

Features

Parts and Descriptions

Dimensions

Inside the Box

Mounting the Camera

Connecting to Monitors

Adjusting the Camera Lens

Adjusting the 3-Axis Gimbal

4

5

6

7

8-13

14-15

16

17

18-29

31

32-33

34-37

Remote Control 30

4

FEATURES*

1/3” Sony Super HAD CCD II

620 TV Lines (B&W), 600 TV Lines (Color)

OMNI-Focus 2.9~8.5mm Auto Iris Lens

3X Motorized Zoom

50ft Range IR with Intelligent Camera Sync [DWC-V4382TIR & V4382TIRH]

Electronic Day and Night [DWC-V4382D Only]

True Day and Night [DWC-V4382TIR & DWC-V4382TIRH]

Smart DNR (Digital Noise Reduction)

WDR (Wide Dynamic Range)

Star-Light (Super Low Light Technology)

HME (Highlight Masking Exposure)

Programmable Privacy Zones & Motion Detection

Easy Icon Driven OSD Menu with Built-In Joystick

IP68 Certified (Water Submersible)

Heater Built-in [DWC-V4382TIRH Only]

Junction Box Included

UTP & RS485 Built-In

Auto Sensing 12VDC or 24VAC with Line Lock

Secondary Video-BNC Output

5

PART & DESCRIPTIONS*

1

Lens

Power Input Connector (Dual Voltage)

UTP

RS-485

Primary Video-BNC Output Connector

Camera Control Board

Bubble Dome Cover

Upper Case

Flush Mount Base

Surface Mount Base / Junction Box

Assembly Screws (#8 - 32 x 0.75)

Secondary Video-BNC Output Connector

Safety Wire

Mounting Screws

2

3

4

5

6

7

8

9

10

11

12

13

14

NO IR

IR

7

8

1

2

12

3

4

5

6

9

10

11

13

14

6

DIMENSIONS IN MILLIMETERS (IN)*

101(3.98”)

137(5.39”)

17(0.67”)

28(1.1”)

54(2.13”)

98.8(3.89”)

121

(4.76”)

118.8

(4.68”)

139(5.47”)139(5.47”)

36(1.42”)

29(1.41”)

53.8(2.12”)

Flush Mount

Surface Mount

121

(4.76”)

7

INSIDE THE BOX*

Included with Snapit Vandal Dome Camera

User Manual

Mounting Template

4 Machine Screws and 4 Dry Wall Anchors

TORX-T20 Wrench

L-Wrench

TORX-T20 Bolt

DC Plug

Secondary Video-BNC Cable

IR Remote Controller

1

2

3

4

5

6

7

8

7 8

9

SURFACE MOUNT INSTALLATION INSTRUCTIONS*

Use the camera’s mounting

template or your camera to

mark the holes as required.

Drill holes into the drywall and

insert the drywall mounts into

the holes.

Pull wires through and make

connections.

If you need to keep the wiring within the

camera housing, refer to the diagram

below.

Mount the surface mount

base (junction box) to the

wall.

DC 12V

AC 24V

UTP

RS485

To use the side conduit, remove the

security screw with the supplied

3.0mm Allen key, and unscrew the

conduit plug.

Route wiring behind

the inner posts

(dark gray area).

DC 12V

AC 24V

UTP

RS485

1 2 3

4

8

9

Secure the three (3) assembly

screws.

Adjust the camera’s position

by using the 3-Axis Gimbal.

Tighten the three locking

screws in with the L-Wrench

to secure the dome cover

over the camera.

Snap the camera module onto

the base by aligning the red

and black markings on the

base and the camera module.

5

6 7 8

10

FLUSH MOUNT INSTALLATION INSTRUCTIONS*

For a flush mount housing, detach the surface mount base,

which is also known as the junction box, from the flush

mount base.

Use the mounting template to mark the holes for the screws

and a larger hole for the top extruded component of the

flush mount base.

The three assembly screws (ST4X35) fixed to the flush

mount base should be used to mount the camera to the

surface of the wall or ceiling.

ST4X35

Secure the three (3) assembly

screws.

Adjust the camera’s position

by using the 3-Axis Gimbal.

Tighten the three locking

screws in with the L-Wrench

to secure the dome cover

over the camera.

1

2

3 4 5

WALL MOUNT INSTALLATION INSTRUCTIONS*

Check to see all parts are in

the box.

Insert the wires from the

camera through the wall

mount housing.

Use the mounting template to

make pilot holes. Use the dry

wall anchors and woods screws

to attach the assembly.

Attach the camera’s surface

mount base (junction box) to

the wall mount.

Connect all cables and snap

the camera module onto the

base.

11

Adjust the camera and

secure the dome cover over

the camera module.

1 2 3

4 5 6

PENDANT MOUNT INSTALLATION INSTRUCTIONS*

Check to see all parts are in

the box.

Attach the top shield to the

pendant mount.

Run all necessary cables

from the ceiling to the mount.

Use the mounting template

to make pilot holes. Use the

dry wall anchors and wood

screws to attach the assembly

to the wall.

Connect all cables and verify

camera is operating properly.

Attach the camera to the

ceiling mount and secure the

dome cover properly.

12

1 2 3

4 5 6

CORNER MOUNT INSTALLATION INSTRUCTIONS*

Check to see all parts are in the box.

Attach the two compression fittings to the

corner bracket.

Attach the wall mount bracket to the corner

mount using the machine screws.

Mount the camera assembly to the corner of

the wall, using wall mount anchors and

machine screws.

13

1 2

3 4

CONNECTING TO MONITORS*

Power Connection: 12VDC & 24VDC Dual Voltage (Auto Polarity Detection and Protection)

All cameras are equipped with a second video output for on-site configuration.

Use the diagram below to connect to a Monitor or CRT Monitor properly.

DC 12V / AC 24V

CCTV Monitor

Monitor

300.0mm(11.8”)

Second Video Output

NO IRIR

14

UTP SYSTEM*

Passive to Passive

Passive to Active

UTP Cable (Max.300ft)

Passive UTP

DVR(Digital Video Recorder)

Monitor

Including the Passive UTP

DVR(Digital Video Recorder)

Monitor

UTP Cable (Max 3,000ft)

Including the Passive UTP

Active UTP

15

ADJUSTING THE CAMERA LENS*

Follow the instructions provided below to make any lens adjustments.

ZOOM: TELE - WIDE

FOCUS: FAR - NEAR

Focus

Zoom

NO IR

IR

Loosen the zoom and focus handles by rotating them counter-clockwise.

Adjust the field of view by moving the handle RIGHT (TELE) to zoom in or LEFT (WIDE) to zoom out.

After the desired zoom position has been established, adjust the Focus the same way as described

above.

Once the desired adjustments have been made, tighten the handles back by turning them clockwise.

1

2

3

4

16

Rotation 360

o

Panning 360

o

NO IR

IR

NO IR

IR

Tilting 90

o

NO IR

Tilting 75

o

IR

ADJUSTING THE 3-AXIS GIMBAL*

The Gimbal mechanism yields maximum rotation and placement as shown below.

17

18

MODULE OSD MENU*

LENS

BACKLIGHT

AGC

STARLIGHT

3D DNR

EXIT JUMP

EXPOSURE

PRIVACY

SET-UP

COLOR

FUNCTION

MOTION

WB MODE

RED GAIN

BLUE GAIN

D&N MODE

NIGHT C.

NIGHT A.

MASK 1AREA SET

MIRROR

SHARPNESS

GAMMA

SLC

NIGHT UP

EXIT JUMP

SAVE & EXIT

EXIT

TITLE EDIT

DPC SET

LANGUAGE

OSD COLOR

COMMUNICATION

FACTORY SET.

COLOR MODE

EXIT JUMP

SENSITIV.

SHOW INDI.

EXTER-OUT.

EXIT JUMP

MASK 2

MASK 3

MASK 4

MASK 5

MASK 6

MASK 7

MASK 8

EXIT JUMP

MANUAL / DC

OFF / BLC / HME / WDR

OFF / LOW / MID / HIGH / HIGHEST

OFF / x2 ~ x1024

OFF / LOW / MID / HIGH / SMART

SAVE& EXIT / EXIT

AWC / ATW / MANUAL / PUSHLOCK

0 ~ 255

NORMAL / COOL / WARM

SAVE& EXIT / EXIT

AUTO / COLOR / B&W

0 ~ 100

SAVE & EXIT / EXIT

MIRROR / OFF

0 ~ 30

MANUAL / 0.45 / 0.60 / 1.0

OFF / ON

SAVE& EXIT / EXIT

AREA 1~4 > OFF / ON

1 ~ 30

OFF / ICON / TRACE

OFF / ON

SAVE & EXIT / EXIT

OFF / ON

OFF / AUTO

ENGLISH /

简

/

DEUTSCH / FRENCH / ITALIAN /

RUSSIAN / SPANISH / DUTCH

BLUE / GREEN / CYAN / RED /

MAGENTA / YELLOW / PURPLE /

GRAY

OFF / ON

SAVE& EXIT / EXIT

DAY & NIGHT

EXIT

EXIT JUMP

NO / YES

SAVE & EXIT / EXIT

MONITOR

MODE 1 / MODE 2

19

EXPOSURE

LENS

Manual Manual mode supports the fixed board lens or the manual iris

lens.

DC DC mode supports the auto-iris varifocal lens.

NOTE: Both MANUAL and DC mode have FOCUS TARGET. You can adjust

the focus by finding the highest number on the FOCUS TARGET.

See page 16 for focus information.

ELC Levels and DC Levels are adjustable. The higher the number, the brighter

the image.

E. Shutter sets the shutter speed levels from 1/60 to 1/100000.

*For LENS-MANUAL Mode, the default E.SHUTTER is AUTO.

*For LENS-DC Mode, the default E.SHUTTER is 1/60. Select DC-AUTO for outdoor use.

Select 1/100FLC to run camera in flickerless mode.

Note: The STARLIGHT option cannot be controlled if the E.SHUTTER setting is

above 1/60.

20

EXPOSURE

BACKLIGHT

OFF

BLC BACK LIGHT COMPENSATION

MANUAL User can manually adjust the BLC level in five areas of the scene (TOP, BOTTOM, CENTER, LEFT, RIGHT).

Increase the BLC levels to make the image brighter.

SMART This is recommended. Camera will automatically detect and adjust the BLC zone. BLC levels to choose

from include: LOWEST, LOW, MID, HIGH.

HME HIGHLIGHT MASKING EXPOSURE

HME masks highlights to allow objects to appear clearly on the screen. If ON is selected, HME levels are

adjustable. The lower the number, the darker the masking areas.

WDR (TRUE) WIDE DYNAMIC RANGE

True WDR in this camera is not supported by a double scan CCD. However, this special DSP can automatically

perform two scans depending on the lighting.

Page is loading ...

Digital Watchdog Snapit DWC-V4382TIR User manual

This manual is also suitable for

Digital Watchdog Snapit DWC-V4382TIR User manual

Related papers

Other documents