Orion Car Audio XTR52 User manual

Category
Car speakers
Type
User manual

This manual is also suitable for

© 2008 directed electronics—all rights reserved 1
TABLE OF CONTENTS
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Français
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Italiano
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Português
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Practice Safe Sound™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Tools of the Trade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Finding Speaker Mounting Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Door Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Rear Deck Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing the Mid/Woofers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing the Tweeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tweeter level controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . back cover
INTRODUCTION
Thank you for your purchase of the Orion XTR Component Loudspeaker system. These speakers
represent a combination of incredible performance and value. The Orion stamped steel frame
components feature treated paper cones and silk dome tweeters. Capable of maintaining their
balance and clarity at exceptionally high output levels, they are the perfect complement to the
Orion woofers. The crossovers feature tweeter level adjustment. The components are available
in standard 5-1/4" and 6-1/2" sizes to fit most applications.
We at Orion strive to give you all the latest up to date information about this product. What we
can't give you in this manual is personal installation or technical experience. If you have questions
concerning the use or application of this product, please refer to the nearest Authorized Orion
Dealer for assistance or call the Orion technical support hot-line at 1-800-876-0800. As we are
always finding new ways to improve our product, the features and specifications are subject to
change without notice.
PRACTICE SAFE SOUND™
Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss.
High powered automotive sound systems can generate sound pressure levels in excess of 130dB.
When playing your system at high levels, please use hearing protection and prevent long term
exposure.
2 © 2008 directed electronics—all rights reserved
Model Number: _____________________________
Serial Number: _____________________________
Date of Purchase: _____________________________
WHAT’S IN THE BOX
Included in this box are all the necessary mounting hardware and cables for your basic
installation. Listed below is a detailed list of the components included in this system package.
Quantity Description
1 Owner's Manual
2 Orion Tweeter Elements
2 Surface mount hardware
2 Flush mount hardware
2 Orion mid/woofer speakers
2 Passive crossovers with cables
1 Mounting template
2 Grilles
Mounting screws
TOOLS OF THE TRADE
Listed are the majority of the tools required to perform the installation. Having the proper tools
will make the installation much easier. It is very difficult when you get half way through the
installation and discover that you require a specific tool to get yourself through a particular part
of the installation. Some of these tools are necessities. Some make the job much easier.
o Marking Pen o Electric Drill
o 1/4" Drill Bit o Phillips Screwdriver
o 1/8" Drill Bit o Volt/Ohm Meter (Optional)
o 3/8" Drill Bit o Needle Nose Pliers
o Hole Saw Arbor o Assorted Tin Snips
o Wire Crimpers o Wire Strippers
o 4-3/4" Hole Saw (5-1/4" mid/woofer install)
o 5" Hole Saw (6-1/2" mid/woofer install)
o 2" Hole Saw (for flush mount tweeter installation)
INSTALLATION
The performance of the Orion Component Loudspeaker is directly proportional to the quality of
installation. Care taken during the installation process will be rewarded with years of satisfying
performance. If you are unsure about your installation capabilities, please refer to your local
Authorized Orion Dealer for technical assistance. Orion dealers are trained professionals
dedicated to extracting the maximum performance out of your Orion system. If you decide to
install this speaker system yourself, please read the entire installation section before starting
your installation.
FINDING SPEAKER MOUNTING LOCATIONS
Choosing the correct speaker locations will have the greatest effect on the sound quality of the
system. Different considerations are needed when choosing the locations that best suit your
needs. The locations must be large enough for the speakers to fit. Care is needed to ensure that
© 2008 directed electronics—all rights reserved 3
the location you have chosen will not affect any of the mechanical or electrical operations of
the vehicle.
Determining the best location for the speakers will depend on your cosmetic needs and your
vehicle's interior. If minimal intrusion in your vehicle is desired, factory speaker locations may
be the ticket for you. Placing the speaker in the factory location can often give very desirable
results.
DOOR MOUNTING
When checking for possible speaker locations in the doors, check the operation of the window
and all assemblies. There is also a stabilizer stop bar in between the door and the door jamb.
This bar prevents the door from opening too far. Many shade tree installers overlook this and
check for clearance only when the door is fully open.
Figure 1
Figura 1
Abbildung 1
Inside
of Door
Speaker
cut out
Dampening Mat
Speaker installed
with no gaps
or air leaks
Dampening on
top of outer
door skin
Door
Panel
Grille
Screws
REAR DECK MOUNTING
In rear deck installations, check the operation of the trunk suspension springs or tension bars.
These tension bars move in the opening and closing of the trunk. You cannot be too cautious
during this part of the installation, In addition, do not locate the speakers too close to the back
of the rear deck. Installing the far screws will only be possible with the removal of the rear
window.
Figure 2
Figura 2
Abbildung 2
Rear/Trunk
of Car
Rear Seat
4 © 2008 directed electronics—all rights reserved
INSTALLING THE MID/WOOFERS
Step 1: Determine where the speakers will be mounted. Make sure there is a flat area large
enough for the speakers to fit properly. An uneven mounting surface can damage the
driver.
Step 2: Check to make sure the space you have chosen for the speakers will not interfere with
the operation of the vehicle.
Step 3: Using the supplied template guide, mark the mounting hole and mounting screw hole
locations with a pen for each speaker.
Step 4: Cut the holes for the speaker. When using correctly sized factory locations, this step
can be passed. A hole can be cut either with a pair of metal tin snips, an air or jig saw,
or with a hole saw corresponding to the size of the midrange listed below.
o 4-3/4" Hole Saw (5-1/4" woofer installation)
o 5" Hole Saw (6-1/2" woofer installation)
WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill.
Step 5: Run the speaker wire to the speakers. Make sure to keep wires away from sharp metal
or other edges. When passing through metal, use a protective grommet.
Step 6: Pre-drill mounting screw holes using a 1/8" drill bit.
WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill.
Step 7: Pull the wire through the speaker opening and connect to the speaker. Be sure to
observe proper mid/woofer polarity during this process.
Step 8: Mount the speaker- Place the speaker and the grille in the installation hole. Align the
mounting screw holes and drive in the four mounting screws.
Screws Speaker
Wiring
Harness
Panel
Figure 3
Figura 3
Abbildung 3
© 2008 directed electronics—all rights reserved 5
INSTALLING THE TWEETER
SURFACE MOUNTING
Step 1: Determine the tweeter mounting location, then route the wires from the crossover to
the tweeter location.
Step 2: Place the provided template or tweeter cup against the panel and mark the two holes
at the rear of the housing.
Step 3: Drill the smaller holes using a 1/8" drill bit. These are the mounting screw holes.
WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill.
Step 4: Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the
speaker wire from the crossover through the grommet.
Step 5: After removing the surface mount tweeter assembly trim ring, route the tweeter wires
through the larger hole in the housing and connect to the speaker wires from the
crossover. (See Figure 4.)
Step 6: Insert the excess speaker wire into the hole and position the housing so the housing
will not pinch the wires after final mounting.
Step 7: Attach the housing using the supplied screws of the correct length for a solid mount.
Step 8: Insert the tweeter into the housing and attach the surface mount trim ring.
Figure 4
Figura 4
Abbildung 4
Surface
Mount
Trim Ring
Mounting
Screws
Surface Mount Housing
Tweeter
Tweeter
Wire
Panel
Wiring
Harness
FULL FLUSH MOUNTING
Step 1:. Determine where the tweeter will be mounted. Make sure there is a flat area large
enough for the tweeter and no obstructions behind the area.
Step 2: Using the back half of the tweeter housing, mark with a pen the hole needed for the
tweeter.
Step 3: Be sure the hole is large enough for the tweeter housing, but not so large that the
flange will not cover the hole..
Step 4: Cut the hole for the tweeter. When using factory locations, this step can be skipped.
A hole can be cut either with a pair of metal tin snips or a 2" hole saw for hard
materials.
WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill.
6 © 2008 directed electronics—all rights reserved
Step 5: Install tweeter in flush mount housing.
Step 6: Connect the speaker wires observing the correct polarity.
Step 7: Install tweeter and housing in the hole cut for mounting, so that the trim ring is flat
with the front of the surface.
Step 8: Use the supplied X bracket & screw to secure the housing to the surface.
Figure 5
Figura 5
Abbildung 5
Flush Mount
Tweeter Assembly
Tweeter
Cup
X Bracket
Tweeter
Wire
Flush Mount
Trim Ring
Wiring
Harness
Panel
Screw
INSTALLING THE CROSSOVER
Step 1: Find a location for the crossover away from any factory or after market electrical wires.
It is recommended to mount the passive crossover close to the amplifier.
Step 2: Mount the crossover using the supplied screws.
Step 3: Connect the wires. Make sure the speaker wires for the midrange go to the mid/
woofer output and the tweeter to the tweeter output. Be sure to observe the correct
polarity. Changing the polarity of the tweeter may be necessary for optimum sound
quality.
TWEETER LEVEL CONTROLS
The three position switch in the crossover box labeled “TW Level” adjusts the relative volume
of the tweeter with respect to the midrange. The 0db position is referenced as equal output
from the midrange and the tweeter. The -3dB and +3dB positions offer -3dB less and +3dB more
output from the tweeter respectively. Tweeter level can be adjusted independently for right and
left channels to compensate for different listening tastes and mounting locations.
© 2008 directed electronics—all rights reserved 7
WIRING DIAGRAM
To Woofer
To Tweeter
To Amplifier
Note: The tweeter positive is the wire marked with the stripe.
Note: Le câble positif du haut-parleur d'aigus est rayé.
Nota. El positivo del tweeter es el cable que tiene la franja.
Hinweis: Der positive Hochtönerdraht ist mit dem Streifen markiert.
Nota: il filo positivo del tweeter è contrassegnato da una striscia.
Nota: O cabo positivo do tweeter está marcado com a listra.
Output
Crossover
Input
+
_
+
_
+
_
Figure 6
Figura 6
Abbildung 6
8 © 2008 directed electronics—all rights reserved
SPECIFICATIONS
Model XTR52 XTR62
Nominal Impedance
4 Ω 4 Ω
Power Continuous/Maximum 50 /100 W 60 /120 W
Frequency Response 80 - 22kHz 75 - 22kHz
Sensitivity (2.83V @ 1M) 88dB 90dB
Mounting Depth 2.29"/58mm 2"/51mm
Mounting Diameter 4.72"/120mm 5"/127mm
FEATURES
Cone moisture and UV resistant paper cone
Surround Butyl rubber
Voice Coil 2 layer copper wire on a Kapton former
Tweeter silk dome - Ferrofluid
Spider single interlaced Conex
Stamped steel baskets with Euro mounting configurations
Two way systems have custom crossover with 12 dB high pass, 6 dB low pass and tweeter
protection
Swivel tweeter
3 position tweeter level adjustment switch (-3dB, 0dB & +3dB)
NOTE: All Specifications are subject to change without notice.
Figure 7
Figura 7
Abbildung 7
E
D
A
B
C
XTR52 XTR62
Dimensions inches/mm, Dimensions pouces/mm,
Dimensiones plg./mm, Abmessungen Zoll/mm,
Dimensioni pollici/millimetri, Dimensões
polegadas/mm
A 2.29/58 2/51
B 0.91/23 0.79/20
C 2.76/70 3.19/81
D 4.72/120 5/127
E 5.16/131 6.50/165
© 2008 Directed Electronics. All rights reserved GXTR52 2008-10
Vista, CA 92081
WWW.DIRECTED.COM
Directed Electronics is committed to delivering
world class quality products and services
that excite and delight our customers.
Directed Electronics is an
ISO 9001 registered company.
WARRANTY
LIMITED ONE-YEAR CONSUMER WARRANTY/*LIMITED TWO-YEAR CONSUMER WARRANTY FOR AUTHORIZED
DIRECTED DEALER PURCHASE & INSTALLATION
Directed Electronics (herein “Directed”) promises to the original purchaser of the subwoofer or amplifier, as
applicable (herein “Unit” or “Product”), to repair or replace with a new or refurbished Unit (at Directed’s
sole and absolute discretion) should the Unit prove to be defective in workmanship or material under normal
use, for a period of *two-years from the date of purchase from the authorized Directed dealer PROVIDED
the Unit was purchased and installed by an authorized Directed dealer. During this *two-year period, there
will be no charge for the repair or replacement PROVIDED the Unit is returned to Directed (DO NOT RETURN
THE ENTIRE ENCLOSURE. PLEASE RETURN THE WARRANTIED UNIT ONLY.), shipping prepaid, along with the
required proof of installation, the bill of sale or other dated proof of purchase, and the consumer’s contact
information. If the Unit is installed by anyone other than an authorized Directed dealer, the warranty period
will be one-year from the date of purchase. This warranty is non-transferable and does not apply to any Unit
that has been modified or used in a manner contrary to its intended purpose, and does not cover damage to
the Unit caused by installation or removal of the Unit. During this one-year period, there will be no charge
for the repair or replacement PROVIDED the Unit is returned to Directed, shipping pre-paid, along with
the bill of sale or other dated proof of purchase and the consumer’s contact information. This warranty is
void if the product has been damaged by accident or unreasonable use, neglect, improper service or other
causes not arising out of defects in materials or construction. This warranty does not cover the elimination
of externally generated static or noise, or the correction of antenna problems or weak reception, damage to
speakers, accessories, electrical systems, cosmetic damage or damage due to negligence, misuse, failure to
follow operating instructions, accidental spills or customer applied cleaners, damage due to environmental
causes such as floods, airborne fallout, chemicals, salt, hail, lightning or extreme temperatures, damage due
to accidents, road hazards, fire, theft, loss or vandalism, damage due to improper connection to equipment
of another manufacturer, modification of existing equipment, or Product which has been opened or tam-
pered for any reason. Units which are found to be damaged by abuse resulting in thermally damaged voice
coils are not covered by this warranty but may be replaced at the absolute and sole discretion of Directed.
Unit must be returned to Directed (DO NOT RETURN THE ENTIRE ENCLOSURE. THE UNIT ENCLOSURE IS COV-
ERED BY A SEPARATE 90-DAY LIMITED CONSUMER WARRANTY. PLEASE ONLY RETURN THE WARRANTIED
UNIT UNLESS A WARRANTY CLAIM IS BEING MADE FOR THE ENCLOSURE.), postage pre-paid, with bill of sale
or other dated proof of purchase bearing the following information: consumer’s name, telephone number,
and address, authorized dealer’s name and address, and product description. Unit must be returned to the
following address: ATTN: WARRANTY DEPARTMENT, Directed Electronics , 1 Viper Way, Vista, CA 92081. Note:
This warranty does not cover labor costs for the removal and/or reinstallation of the Unit. IN ORDER FOR
THE TWO-YEAR WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY
AN AUTHORIZED DIRECTED DEALER. ALL UNITS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT
PROOF OF DIRECTED DEALER INSTALLATION AND PURCHASE WILL BE COVERED BY THE LIMITED 1 YEAR
WARRANTY.
BY PURCHASING THIS PRODUCT, ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY,
IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WAR-
RANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM
EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME
FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT. DIRECTED HAS ABSOLUTELY NO
LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS.
IN NO EVENT WILL DIRECTED BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (IN-
CLUDING LOSS OF PROFITS). BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT
ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALI-
FORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA. This warranty is only valid for sale of Product within the
United States of America. Product sold outside of the United States of America is sold “AS-IS,” and shall have
NO WARRANTY, express or implied. Some states do not allow limitation on how long an implied warranty
lasts. In such states, the limitation or exclusions of this Limited Warranty may not apply. Some states do not
allow the exclusion or limitation of incidental or consequential damages. In such states, the exclusion or limi-
tation of this Limited Warranty may not apply to you. This Limited Warranty gives you specific legal rights,
and you may have other rights which vary from state to state. 920-0033 04-07
For more information on Orion products please visit www.orioncaraudio.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

Orion Car Audio XTR52 User manual

Category
Car speakers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI