Garmin 500-PRO-1 Owner's manual

Brand: Garmin

Model: 500-PRO-1

Category: Navigators

Type: Owner's manual

This manual is also suitable for

GPSMAP

500/700 Series and echoMAP

™

50/70

Series

Owner’s Manual

March 2015 Printed in Taiwan 190-01556-10_0D

right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such

changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.

Garmin

, the Garmin logo, BlueChart

, g2 Vision

, GPSMAP

, MapSource

, and Ultrascroll

are trademarks of Garmin Ltd. or its subsidiaries, registered in the

USA and other countries. echoMAP

™

, Garmin Helm

™

, GMR

™

, GSD

™

, GXM

™

, HomePort

™

, LakeVü

™

, and Meteor

™

are trademarks of Garmin Ltd. or its

subsidiaries. These trademarks may not be used without the express permission of Garmin.

Android

™

is a trademark of Google Inc. The Bluetooth

word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is

under license. FUSION-Link

™

is a trademark of Fusion Electronics Ltd. iOS

is a registered trademark of Cisco Systems, Inc. used under license by Apple Inc.

iPod

is a trademark of Apple Inc., registered in the U.S. and other countries. microSD

™

and the microSDHC logo are trademarks of SD-3C, LLC. NMEA

NMEA 2000

, and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. SiriusXM

is a registered trademark of

SiriusXM Radio Inc. Wi‑Fi

is a registered trademark of W-Fi Alliance. Windows

is a registered trademark of Microsoft Corporation in the United States and

other countries. Other trademarks and trade names are those of their respective owners.

Table of Contents

Introduction.....................................................................1

echoMAP 70 Series and GPSMAP 700 Series.......................... 1

Using the Touchscreen.......................................................... 1

echoMAP 50 Series and GPSMAP 500 Series.......................... 1

Device Keys........................................................................... 1

Downloading the Manuals.......................................................... 1

Manual Conventions................................................................... 1

Getting More Information............................................................ 1

Inserting Memory Cards............................................................. 1

Software Update......................................................................... 2

Loading the New Software on a Memory Card...................... 2

Updating the Device Software............................................... 2

GPS Satellite Signals..................................................................2

Selecting the GPS Source..................................................... 2

Customizing the Chartplotter........................................ 2

Customizing the Home Screen................................................... 2

Setting the Vessel Type.............................................................. 2

Adjusting the Backlight............................................................... 2

Adjusting the Color Mode........................................................... 2

Hiding and Showing the Menu Bar............................................. 2

Communication with Wireless Devices........................ 2

Setting Up the Wi‑Fi® Wireless Network.................................... 2

Connecting a Wireless Device to the Chartplotter...................... 3

Changing the Wireless Channel................................................. 3

Using the Garmin Helm App with the Chartplotter...................... 3

Connecting a Bluetooth Wireless Device................................... 3

Disconnecting a Bluetooth Wireless Device............................... 3

Charts and 3D Chart Views........................................... 3

Navigation Chart and Offshore Fishing Chart............................. 3

Zooming In and Out of the Chart........................................... 3

Panning the Chart.................................................................. 3

Selecting an Item on the Map Using the Device Keys........... 4

Measuring a Distance on the Chart....................................... 4

Chart Symbols....................................................................... 4

Navigating to a Point on the Chart......................................... 4

Viewing Location and Object Information on a Chart............ 4

Viewing Details about Navaids.............................................. 4

Selecting a Map..................................................................... 4

Premium Charts.......................................................................... 4

Viewing Tide Station Information........................................... 5

Showing Satellite Imagery on the Navigation Chart.............. 5

Viewing Aerial Photos of Landmarks..................................... 5

Automatic Identification System..................................................5

AIS Targeting Symbols.......................................................... 5

Heading and Projected Course of Activated AIS Targets...... 6

Showing AIS Vessels on a Chart or 3D Chart View.............. 6

Activating a Target for an AIS Vessel.................................... 6

Viewing a List of AIS Threats................................................. 6

Setting the Safe-Zone Collision Alarm................................... 6

AIS Distress Signals.............................................................. 6

Turning Off AIS Reception..................................................... 7

Chart and 3D Chart View Settings.............................................. 7

Navigation and Fishing Chart Setup...................................... 7

Waypoints and Tracks Settings on the Charts and Chart

Views..................................................................................... 7

Laylines Settings.................................................................... 7

Overlay Numbers Settings..................................................... 7

Showing a Navigation Inset................................................... 8

Chart Appearance Settings.................................................... 8

Setting the Heading and Course Over Ground Lines............ 8

Other Vessels Settings on the Charts and Chart Views........ 8

Fish Eye 3D Settings............................................................. 9

Navigation with a Chartplotter...................................... 9

Basic Navigation Questions

........................................................ 9

Destinations................................................................................ 9

Searching for a Destination by Name.................................... 9

Selecting a Destination Using the Navigation Chart.............. 9

Searching for a Marine Services Destination......................... 9

Stopping Navigation....................................................................9

Waypoints................................................................................... 9

Marking Your Present Location as a Waypoint...................... 9

Creating a Waypoint at a Different Location........................ 10

Marking and Starting Navigation to an MOB Location......... 10

Viewing a List of all Waypoints............................................ 10

Editing a Saved Waypoint.................................................... 10

Moving a Saved Waypoint................................................... 10

Browsing for and Navigating to a Saved Waypoint.............. 10

Deleting a Waypoint or an MOB.......................................... 10

Deleting All Waypoints......................................................... 10

Setting and Following a Direct Course Using Go To........... 10

Routes...................................................................................... 10

Creating and Navigating a Route From Your Present

Location............................................................................... 10

Creating and Saving a Route............................................... 11

Viewing a List of Routes and Auto Guidance Paths............ 11

Editing a Saved Route......................................................... 11

Browsing for and Navigating a Saved Route....................... 11

Browsing for and Navigating Parallel to a Saved Route...... 11

Deleting a Saved Route....................................................... 11

Deleting All Saved Routes................................................... 11

Auto Guidance.......................................................................... 11

Setting and Following an Auto Guidance Path.................... 11

Creating and Saving an Auto Guidance Path...................... 12

Adjusting an Auto Guidance Path........................................ 12

Canceling an Auto Guidance Calculation in Progress......... 12

Setting a Timed Arrival.........................................................12

Auto Guidance Line Configurations..................................... 12

Tracks....................................................................................... 12

Showing Tracks................................................................... 13

Setting the Color of the Active Track................................... 13

Saving the Active Track....................................................... 13

Viewing a List of Saved Tracks............................................ 13

Editing a Saved Track.......................................................... 13

Saving a Track as a Route...................................................13

Browsing for and Navigating a Recorded Track.................. 13

Deleting a Saved Track........................................................13

Deleting All Saved Tracks.................................................... 13

Retracing the Active Track................................................... 13

Clearing the Active Track..................................................... 13

Managing the Track Log Memory During Recording........... 13

Configuring the Recording Interval of the Track Log........... 13

Stopping Navigation................................................................. 13

Synchronizing User Data Across the Garmin Marine

Network.....................................................................................13

Deleting All Saved Waypoints, Routes, and Tracks................. 13

Combinations............................................................... 14

Selecting a Combination........................................................... 14

Customizing a Combination Screen......................................... 14

Adding a Custom Combination Screen.................................... 14

Sonar............................................................................. 14

Sonar Views..............................................................................14

Traditional Sonar View......................................................... 14

DownVü Sonar View............................................................ 14

SideVü Sonar View.............................................................. 14

Split-Screen Sonar Views.................................................... 15

Split-Zoom Sonar View........................................................ 15

Split-Frequency Sonar View................................................ 15

Panoptix™ Sonar Views...................................................... 15

Changing the Sonar View......................................................... 16

Table of Contents i

Creating a Waypoint on the Sonar Screen Using the

Touchscreen............................................................................. 16

Creating a Waypoint on the Sonar Screen Using the Device

Keys.......................................................................................... 16

Measuring Distance on the Sonar Screen................................ 16

Pausing the Sonar Display....................................................... 16

Viewing Sonar History.............................................................. 16

Sonar Sharing........................................................................... 16

Selecting a Sonar Source.................................................... 16

Renaming a Sonar Source...................................................16

Customizing the Overlay Numbers........................................... 16

Adjusting the Level of Detail..................................................... 17

Adjusting the Color Intensity..................................................... 17

Adjusting the Range of the Depth or Width Scale.................... 17

Setting the Zoom Level on the Sonar Screen........................... 17

Setting the Scroll Speed........................................................... 17

Sonar Frequencies................................................................... 17

Selecting Frequencies......................................................... 18

Creating a Frequency Preset............................................... 18

Customizing the Panoptix Sonar Views.................................... 18

Adjusting the Appearance of the LiveVü Sonar Views........ 18

Setting the LiveVü Transducer Transmit Angle................... 18

Adjusting the RealVü Viewing Angle and Zoom Level......... 18

Adjusting the Appearance of the RealVü Sonar Views........ 18

Adjusting the RealVü Sweep Speed.................................... 18

Turning On the A-Scope........................................................... 18

Selecting the Transducer Type................................................. 18

Sonar Setup.............................................................................. 18

Sonar Settings..................................................................... 18

RealVü Sonar Settings.........................................................19

LiveVü Sonar Settings......................................................... 19

Sonar Appearance Settings................................................. 19

Sonar Alarm Settings........................................................... 19

Advanced Sonar Settings.................................................... 19

Transducer Installation Settings...........................................19

Sonar Recordings..................................................................... 20

Recording the Sonar Display............................................... 20

Stopping the Sonar Recording............................................. 20

Deleting a Sonar Recording................................................. 20

Playing Sonar Recordings................................................... 20

Depth and Water Temperature Graphs.................................... 20

Setting the Depth and Water Temperature Graph Range and

Time Scales......................................................................... 20

Radar............................................................................. 20

Radar Display Modes............................................................... 20

Transmitting Radar Signals...................................................... 20

Adjusting the Radar Range...................................................... 21

Tips for Selecting a Radar Range........................................ 21

Adjusting the Zoom Scale on the Radar Screen...................... 21

Marking a Waypoint on the Radar Screen................................ 21

Sentry Mode............................................................................. 21

Enabling Timed Transmit..................................................... 21

Setting the Standby and Transmit Times............................. 21

Enabling a Guard Zone........................................................ 21

Defining a Circular Guard Zone........................................... 21

Defining a Partial Guard Zone............................................. 21

Viewing a List of AIS Threats............................................... 21

Showing AIS Vessels on the Radar Screen........................ 21

VRM and EBL........................................................................... 22

Showing the VRM and the EBL........................................... 22

Adjusting the VRM and the EBL.......................................... 22

Measuring the Range and Bearing to a Target Object........ 22

Radar Overlay...........................................................................22

Radar Overlay and Chart Data Alignment........................... 22

Showing the Radar Overlay................................................. 22

Setting a Custom Park Position................................................ 22

Enabling and Adjusting a Radar No Transmit Zone

................. 22

Stopping the Transmission of Radar Signals........................... 22

Optimizing the Radar Display................................................... 22

Radar Gain and Clutter........................................................ 22

Echo Trails........................................................................... 23

Radar Display Settings........................................................ 24

Radar Appearance Settings................................................. 24

Front-of-Boat Offset............................................................. 24

Gauges and Almanac Information.............................. 24

Viewing the Compass............................................................... 24

Viewing Trip Gauges................................................................ 24

Resetting Trip Gauges......................................................... 24

Viewing Engine and Fuel Gauges............................................ 24

Customizing Engine Gauge and Fuel Gauge Limits............ 24

Enabling Status Alarms for Engine Gauges........................ 24

Enabling Some Engine Gauge Status Alarms..................... 25

Selecting the Number of Engines Shown in Gauges........... 25

Customizing the Engines Shown in Gauges........................ 25

Configuring the Fuel Gauges Display.................................. 25

Setting the Fuel Capacity of the Vessel............................... 25

Synchronizing the Fuel Data with the Actual Vessel Fuel... 25

Setting the Fuel Alarm......................................................... 25

Viewing the Wind Gauges........................................................ 25

Configuring the Sailing Wind Gauge.................................... 25

Configuring the Speed Source............................................. 25

Configuring the Heading Source of the Wind Gauge........... 25

Customizing the Close-Hauled Wind Gauge....................... 25

Viewing the Environment Gauges............................................ 25

Configuring the Alignment of the Wind Gauge.................... 25

Configuring the Heading Source of the Environment

Gauge.................................................................................. 26

Setting the Barometer Reference Time............................... 26

Tide, Current, and Celestial Information................................... 26

Tide Station Information....................................................... 26

Current Station Information.................................................. 26

Celestial Information............................................................ 26

Viewing Tide Station, Current Station, or Celestial Information

for a Different Date...............................................................26

Viewing Information for a Different Tide or Current

Station.................................................................................. 26

Viewing Almanac Information from the Navigation Chart.... 26

Digital Selective Calling............................................... 26

Networked Chartplotter and VHF Radio Functionality.............. 26

Turning On DSC....................................................................... 26

DSC List....................................................................................26

Viewing the DSC List........................................................... 26

Adding a DSC Contact......................................................... 26

Incoming Distress Calls............................................................ 26

Navigating to a Vessel in Distress....................................... 27

Man-Overboard Distress Calls Initiated from a VHF

Radio....................................................................................27

Man-Overboard and SOS Distress Calls Initiated from the

Chartplotter.......................................................................... 27

Position Tracking...................................................................... 27

Viewing a Position Report.................................................... 27

Navigating to a Tracked Vessel........................................... 27

Creating a Waypoint at the Position of a Tracked Vessel.... 27

Editing Information in a Position Report.............................. 27

Deleting a Position-Report Call............................................ 27

Viewing Vessel Trails on the Chart...................................... 27

Individual Routine Calls............................................................ 27

Selecting a DSC Channel.................................................... 27

Making an Individual Routine Call....................................... 27

Making an Individual Routine Call to an AIS Target............ 28

Media Player................................................................. 28

ii Table of Contents

Opening the Media Player........................................................ 28

Icons.................................................................................... 28

Selecting the Media Source...................................................... 28

Connecting a Bluetooth Wireless Device to the Media

Player

................................................................................... 28

Playing Music............................................................................28

Browsing for Music...............................................................28

Setting a Song to Repeat..................................................... 28

Setting All Songs to Repeat................................................. 28

Setting Songs to Shuffle...................................................... 28

Listening to the Radio.......................................................... 28

Opening the MTP Source.................................................... 28

Adjusting the Volume................................................................ 28

Enabling and Disabling Zones............................................. 28

Muting the Media Volume.................................................... 29

Scanning VHF Channels.......................................................... 29

Adjusting the VHF Squelch....................................................... 29

Setting the Device Name.......................................................... 29

SiriusXM® Satellite Radio........................................................ 29

Locating a SiriusXM Radio ID.............................................. 29

Activating a SiriusXM Subscription...................................... 29

Customizing the Channel Guide.......................................... 29

Saving a SiriusXM Channel to the Presets List................... 29

Unlocking SiriusXM Parental Controls................................. 29

Viewing Video............................................................... 29

Configuring the Video Appearance........................................... 29

SiriusXM Weather......................................................... 30

SiriusXM Equipment and Subscription Requirements.............. 30

Weather Data Broadcasts.........................................................30

Viewing Precipitation Information............................................. 30

Precipitation Views...............................................................30

Storm Cell and Lightning Information....................................... 30

Hurricane Information............................................................... 30

Weather Warnings and Weather Bulletins................................ 30

Forecast Information................................................................. 30

Viewing Forecast Information for Another Time Period....... 30

Viewing a Marine Forecast or an Offshore Forecast........... 31

Weather Fronts and Pressure Centers................................ 31

City Forecasts...................................................................... 31

Viewing Sea Conditions............................................................ 31

Surface Winds......................................................................31

Wave Height, Wave Period, and Wave Direction................ 31

Viewing Forecast Sea Conditions Information for Another

Time Period..........................................................................31

Viewing Fishing Information......................................................31

Surface Pressure and Water Temperature Data................. 31

Forecasting Fish Locations.................................................. 31

Changing the Sea Surface Temperature Color Range........ 31

Visibility Information.................................................................. 32

Viewing Forecast Visibility Information for Another Time

Period...................................................................................32

Viewing Buoy Reports.............................................................. 32

Viewing Local Weather Information near a Buoy................. 32

Creating a Waypoint on a Weather Chart................................. 32

Weather Overlay....................................................................... 32

Turning On the Weather Overlay on a Chart....................... 32

Weather Overlay Settings on the Navigation Chart............. 32

Weather Overlay Settings on the Fishing Chart.................. 32

Viewing Weather Subscription Information............................... 32

Device Configuration................................................... 32

Turning On the Chartplotter Automatically............................... 32

System Settings........................................................................ 32

Display Settings................................................................... 33

GPS Settings....................................................................... 33

Viewing the Event Log......................................................... 33

Viewing System Software Information

................................. 33

My Vessel Settings................................................................... 33

Setting the Keel Offset......................................................... 33

Calibrating a Water Speed Device....................................... 33

Setting the Water Temperature Offset................................. 34

Communications Settings......................................................... 34

NMEA 0183..........................................................................34

NMEA 2000 Settings............................................................34

Setting Alarms.......................................................................... 34

Navigation Alarms................................................................ 34

System Alarms..................................................................... 34

Setting the Fuel Alarm......................................................... 34

Setting Weather Alarms....................................................... 34

Units Settings............................................................................34

Navigation Settings................................................................... 35

Auto Guidance Line Configurations..................................... 35

Adjusting the Distance from Shore...................................... 35

Other Vessel Settings............................................................... 36

Restoring the Original Chartplotter Factory Settings................ 36

Chartplotter Data Management................................... 36

Copying Waypoints, Routes, and Tracks from HomePort to a

Chartplotter............................................................................... 36

Selecting a File Type for Third-Party Waypoints and Routes... 36

Copying Data from a Memory Card.......................................... 36

Copying Waypoints, Routes, and Tracks to a Memory Card.... 36

Copying Built-In Maps to a Memory Card................................. 36

Backing Up Data to a Computer............................................... 36

Restoring Backup Data to a Chartplotter.................................. 36

Saving System Information to a Memory Card......................... 36

Appendix....................................................................... 36

Registering Your Device........................................................... 36

Cleaning the Screen................................................................. 37

Calibrating the Touchscreen..................................................... 37

Screenshots.............................................................................. 37

Capturing Screenshots........................................................ 37

Copying Screenshots to a Computer................................... 37

Troubleshooting........................................................................ 37

My device will not acquire GPS signals............................... 37

My device will not turn on or keeps turning off..................... 37

My device is not creating waypoints in the correct

location.................................................................................37

The touchscreen is not responding to my touches.............. 37

NMEA 0183 Information........................................................... 37

NMEA 2000 PGN Information...................................................38

Software License Agreement................................................... 38

Index.............................................................................. 39

Table of Contents iii

Introduction

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

echoMAP 70 Series and GPSMAP 700 Series

Power key

Automatic backlight sensor

Touchscreen

microSD

™

memory card slots

Using the Touchscreen

• Tap the screen to select an item.

• Drag or swipe your finger across the screen to pan or scroll.

• Pinch two fingers together to zoom out.

• Spread two fingers apart to zoom in.

Locking the Touchscreen

You can lock the touchscreen to prevent inadvertent screen

touches.

Select .

Select Lock Touchscreen.

echoMAP 50 Series and GPSMAP 500 Series

Automatic backlight sensor

Power key

Device keys

microSD memory card slots

Device Keys

Turns on and off the device when held.

Adjusts the backlight and color mode when quickly pressed

and released.

Zooms out of a chart or view.

Zooms in to a chart or view.

Scrolls, highlights options, and moves the cursor.

SELECT Acknowledges messages and selects options.

BACK Returns to the previous screen.

MARK Saves the present location as a waypoint.

HOME Returns to the Home screen.

MENU Opens a menu of options for the page, when applicable.

Closes a menu, when applicable.

Downloading the Manuals

You can get the latest owner's manual and translations of

manuals from the web.

Go to www.garmin.com/support.

Select Manuals.

Follow the on-screen instructions to download the manual for

your product.

Manual Conventions

In this manual, the term “select” is used to describe these

actions.

• Touching an item on the screen (for touchscreen devices

only).

• Using the arrow keys to highlight a menu item, and then

pressing SELECT (for hard key devices only).

• Pressing a key, such as SELECT or MENU.

When you are instructed to select multiple items in a series,

small arrows appear in the text. For example, "select Menu >

Add," indicates that you need to select the Menu item or hard

key and then select the Add item.

The images in this manual are for reference only and may not

match your device exactly.

Getting More Information

If you have any questions about your device, you can contact

Garmin

Product Support.

The website, www.garmin.com/support, offers many different

troubleshooting tips to help resolve most issues and answer

most questions.

• Frequently-asked questions (FAQs)

• Software updates

• Owner's and installation manuals

• Service alerts

• Video

• Contact numbers and addresses

Inserting Memory Cards

You can use optional memory cards in the chartplotter. Map

cards allow you to view high-resolution satellite imagery and

aerial reference photos of ports, harbors, marinas, and other

points of interest. You can use blank memory cards to record

sonar data and transfer data such as waypoints, routes, and

tracks to another compatible Garmin chartplotter or a computer.

Open the access flap or door on the front of the chartplotter.

Insert the memory card.

Press the card in until it clicks.

Introduction 1

Close the door.

Software Update

You may need to update the device software when you install

the device or add an accessory to the device.

Loading the New Software on a Memory Card

Insert a memory card into the card slot on the computer.

Go to www.garmin.com/support/software/marine.html.

Select Download next to Garmin Marine Network with SD

card.

Read and agree to the terms.

Select Download.

Select Run.

Select the drive associated with the memory card, and select

Next > Finish.

Updating the Device Software

Before you can update the software, you must obtain a

software-update memory card or load the latest software onto a

memory card.

Turn on the chartplotter.

After the home screen appears, insert the memory card into

the card slot.

NOTE: In order for the software update instructions to

appear, the device must be fully booted before the card is

inserted.

Follow the on-screen instructions.

Wait several minutes while the software update process

completes.

The device returns to normal operation after the software

update process is complete.

Remove the memory card.

NOTE: If the memory card is removed before the device

restarts fully, the software update is not complete.

GPS Satellite Signals

When you turn on the chartplotter, the GPS receiver must collect

satellite data and establish the current location. When the

chartplotter acquires satellite signals, appears at the top of

the Home screen. When the chartplotter loses satellite signals,

disappears and a flashing question mark appears over on

the chart.

For more information about GPS, go to www.garmin.com

/aboutGPS.

Selecting the GPS Source

You can select your preferred source for GPS data, if you have

more than one GPS source.

Select Settings > System > GPS > Source.

Select the source for GPS data.

Customizing the Chartplotter

Customizing the Home Screen

You can add items to and rearrange items on the Home screen.

From the Home screen, select Customize Home.

Select an option:

• To rearrange an item, select Rearrange, select the item to

move, and select the new location.

• To add an item to the Home screen, select Add, and

select the new item.

• To remove an item you have added to the Home screen,

select Remove, and select the item.

Setting the Vessel Type

You can select your boat type to configure the chartplotter

settings and to use features customized for your boat type.

Select Settings > My Vessel > Vessel Type.

Select Powerboat or Sailboat.

Adjusting the Backlight

Select Settings > System > Display > Backlight.

TIP: Press from any screen to open the backlight settings.

Select an option:

• Adjust the backlight level.

• Select Auto Backlight.

Adjusting the Color Mode

Select Settings > System > Display > Color Mode.

TIP: Press from any screen to access the color settings.

Select an option.

Hiding and Showing the Menu Bar

NOTE: This feature is not available on all chartplotter models.

You can hide the menu bar automatically to make more screen

space available.

Select Settings > System > Display > Menu Bar Display >

Auto Hide.

After a short period of time on a main page, such as a chart,

the menu bar collapses down.

Swipe the screen from the bottom up to show the menu bar

again.

Communication with Wireless Devices

The chartplotters can create a wireless network to which you

can connect wireless devices.

Some models also can connect to Bluetooth

wireless devices

using the AVRCP profile.

Connecting wireless devices allows you to use Garmin apps,

including BlueChart

Mobile and Garmin Helm

™

. See

www.garmin.com for more information.

Setting Up the Wi‑Fi

Wireless Network

The chartplotters can create a Wi‑Fi network to which you can

connect wireless devices. The first time you access the wireless

network settings, you are prompted to set up the network.

Select Settings > Communications > Wireless Devices >

Wi-Fi® Network > Wi-Fi® > On > OK.

If necessary, enter a name for this wireless network.

Enter a password.

2 Customizing the Chartplotter

You will need this password to access the wireless network

from a wireless device. The password is case-sensitive.

Connecting a Wireless Device to the

Chartplotter

Before you can connect a wireless device to the chartplotter

wireless network, you must configure the chartplotter wireless

network (Setting Up the Wi‑Fi

Wireless Network).

You can connect multiple wireless devices to the chartplotter to

share data.

From the wireless device, turn on the Wi‑Fi technology and

search for wireless networks.

Select the name of your chartplotter wireless network (Setting

Up the Wi‑Fi

Wireless Network).

Enter the network password.

Changing the Wireless Channel

You can change the wireless channel if you have trouble finding

or connecting to a device, or if you experience interference.

Select Settings > Communications > Wireless Devices >

Wi-Fi® Network > Advanced > Wi-Fi® Channel.

Enter a new channel.

You do not need to change the wireless channel of devices

connected to this network.

Using the Garmin Helm App with the

Chartplotter

Before you can control the chartplotter with the Garmin Helm

app, you must download and install the application, and connect

the chartplotter to a mobile device (Connecting a Wireless

Device to the Chartplotter).

Select Settings > Communications > Wireless Devices >

Helm App.

Select an option.

Use the application to view or control the chartplotter.

Connecting a Bluetooth Wireless Device

NOTE: Bluetooth technology is not available on all chartplotter

models.

You can wirelessly connect the chartplotter to a Bluetooth

device.

Place the Bluetooth device within 33 ft. (10 m) of the

chartplotter.

Select Settings > Communications > Wireless Devices >

Bluetooth Devices > Bluetooth.

If necessary, enter a name for this wireless network.

If necessary, enter a password.

You will need this password to access the wireless network

from a wireless device. The password is case-sensitive.

Disconnecting a Bluetooth Wireless Device

Select Settings > Communications > Wireless Devices >

Bluetooth Devices > Device List.

Select a device.

Select Forget Device.

Charts and 3D Chart Views

The charts and 3D chart views that are available depend on the

map data and accessories used.

You can access the charts and 3D chart views by selecting

Charts.

Navigation Chart: Shows navigation data available on your pre-

loaded maps and from supplemental maps, if available. The

data includes buoys, lights, cables, depth soundings,

marinas, and tide stations in an overhead view.

Perspective 3D: Provides a view from above and behind the

boat (according to your course) and provides a visual

navigation aid. This view is helpful when navigating tricky

shoals, reefs, bridges, or channels, and is beneficial when

trying to identify entry and exit routes in unfamiliar harbors or

anchorages.

Mariner’s Eye 3D: Shows a detailed, three-dimensional view

from above and behind the boat (according to your course)

and provides a visual navigation aid. This view is helpful

when navigating tricky shoals, reefs, bridges, or channels,

and when trying to identify entry and exit routes in unfamiliar

harbors or anchorages.

NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are

available with premium charts, in some areas.

Fish Eye 3D: Provides an underwater view that visually

represents the sea floor according to the chart information.

When a sonar transducer is connected, suspended targets

(such as fish) are indicated by red, green, and yellow

spheres. Red indicates the largest targets and green

indicates the smallest.

Fishing Chart: Provides a detailed view of the bottom contours

and depth soundings on the chart. This chart removes

navigational data from the chart, provides detailed

bathymetric data, and enhances bottom contours for depth

recognition. This chart is best for offshore deep-sea fishing.

NOTE: The offshore Fishing chart is available with premium

charts, in some areas.

Radar Overlay: Superimposes radar information on the

Navigation chart or the Fishing chart, when the chartplotter is

connected to a radar. This feature is not available with all

models.

Navigation Chart and Offshore Fishing Chart

NOTE: The offshore Fishing chart is available with premium

charts, in some areas.

The Navigation and Fishing charts allow you to plan your

course, view map information, and follow a route. The Fishing

chart is for offshore fishing.

To open the Navigation chart, select Charts > Navigation

Chart.

To open the Fishing chart, select Charts > Fishing Chart.

Zooming In and Out of the Chart

The zoom level is indicated by the scale number at the bottom of

the chart. The bar under the scale number represents that

distance on the chart.

• Select to zoom out.

• Select to zoom in.

Panning the Chart

You can move the chart to view an area other than your present

location.

From the chart, drag the navigation screen or use the arrow

keys.

Charts and 3D Chart Views 3

Select Stop Panning or Back to stop panning and return the

screen to your present location.

Selecting an Item on the Map Using the Device Keys

From a chart or 3D chart view, select , , , or to move

the cursor.

Select SELECT.

Measuring a Distance on the Chart

From a chart or the Radar overlay, select a location.

Select Measure Distance.

A push pin appears on the screen at your present location.

The distance and angle from the pin is listed in the upper-left

corner.

TIP: To reset the pin and measure from the current location of

the cursor, select Set Reference.

Chart Symbols

This table contains some of the common symbols you might see

on the detailed charts.

Icon Description

Buoy

Information

Marine services

Tide station

Current station

Overhead photo available

Perspective photo available

Other features common to most charts include depth contour

lines, intertidal zones, spot soundings (as depicted on the

original paper chart), navigational aids and symbols,

obstructions, and cable areas.

Navigating to a Point on the Chart

CAUTION

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

When using Go To, a direct course and a corrected course may

pass over land or shallow water. Use visual sightings, and steer

to avoid land, shallow water, and other dangerous objects.

NOTE: The offshore Fishing chart is available with premium

charts, in some areas.

NOTE: Auto Guidance is available with premium charts, in some

areas.

From the Navigation chart or Fishing chart, select a location.

If necessary, select SELECT.

Select Navigate To.

Select an option:

• To navigate directly to the location, select Go To.

• To create a route to the location, including turns, select

Route To.

• To use Auto Guidance, select Auto Guidance.

Review the course indicated by the magenta line.

NOTE: When using Auto Guidance, a gray segment within

any part of the magenta line indicates that Auto Guidance

cannot calculate part of the Auto Guidance line. This is due to

the settings for minimum safe water depth and minimum safe

obstacle height.

Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

Viewing Location and Object Information on a Chart

You can view information about a location or an object on the

Navigation chart or the Fishing chart.

NOTE: The offshore Fishing chart is available with premium

charts, in some areas.

From the Navigation chart or Fishing chart, select a location

or object.

A list of options appears along the right side of the chart. The

options that appear vary based on the location or object you

selected.

Select an option:

• To navigate to the selected location, select Navigate To.

• To mark a waypoint at the cursor location, select New

Waypoint.

• To view the distance and bearing of the object from your

current location, select Measure Distance.

The distance and bearing appear on the screen. Select

Select to measure from a location other than your current

location.

• To view tide, current, celestial, chart notes, or local

services information near the cursor, select Information.

Viewing Details about Navaids

From the Navigation chart, Fishing chart, Perspective 3D chart

view, or Mariner’s Eye 3D chart view, you can view details about

various types of navigation aids, including beacons, lights, and

obstructions.

NOTE: The offshore Fishing chart is available with premium

charts, in some areas.

NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are

available with premium charts, in some areas.

From a chart or 3D chart view, select a navaid.

Select the name of the navaid.

Selecting a Map

If your product has both BlueChart g2 and LakeVü

™

HD built-in

maps, you can select which map to use. Not all models have

both types of built-in maps.

From the Navigation chart, select Menu > Built-in Map.

Select an option:

• When you are on an inland lake, select LakeVü™ HD.

• When you are offshore, select BlueChart® g2.

Premium Charts

CAUTION

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

NOTE: Not all models support all charts.

Optional premium charts, such as BlueChart g2 Vision

, allow

you to get the most out of your chartplotter. In addition to

detailed marine charting, premium charts may contain these

features, which are available in some areas.

Mariner’s Eye 3D: Provides a view from above and behind the

boat for a three-dimensional navigation aid.

Fish Eye 3D: Provides an underwater, three-dimensional view

that visually represents the sea floor according to the

information on the chart.

4 Charts and 3D Chart Views

Fishing Charts: Shows the chart with enhanced bottom

contours and without navigational data. This chart works well

for offshore deep-sea fishing.

High Resolution Satellite Imagery: Provides high-resolution

satellite images for a realistic view of the land and water on

the Navigation chart (Showing Satellite Imagery on the

Navigation Chart).

Aerial Photos: Shows marinas and other navigationally

significant aerial photos to help you visualize your

surroundings (Viewing Aerial Photos of Landmarks).

Detailed Roads and POI data: Shows detailed road and point

of interest (POI) data, which includes highly detailed coastal

roads and POIs such as restaurants, lodging, and local

attractions.

Auto Guidance: Uses specified safe depth, safe height, and

chart data to determine the best course to your destination.

Viewing Tide Station Information

on the chart indicates a tide station. You can view a detailed

graph for a tide station to help predict the tide level at different

times or on different days.

NOTE: This feature is available with premium charts, in some

areas.

From the Navigation chart or Fishing chart, select a tide

station.

Tide direction and tide level information appear near .

Select the station name.

Animated Tide and Current Indicators

NOTE: This feature is available with premium charts, in some

areas.

You can view indicators for animated tide station and current

direction on the Navigation chart or the Fishing chart. You must

also enable animated icons in the chart settings (Showing Tides

and Current Indicators).

An indicator for a tide station appears on the chart as a vertical

bar graph with an arrow. A red arrow pointing downward

indicates a falling tide, and a blue arrow pointing upward

indicates a rising tide. When you move the cursor over the tide

station indicator, the height of the tide at the station appears

above the station indicator.

Current direction indicators appear as arrows on the chart. The

direction of each arrow indicates the direction of the current at a

specific location on the chart. The color of the current arrow

indicates the range of speed for the current at that location.

When you move the cursor over the current direction indicator,

the specific current speed at the location appears above the

direction indicator.

Color Current Speed Range

Yellow 0 to 1 knot

Orange 1 to 2 knots

Red 2 or more knots

Showing Tides and Current Indicators

NOTE: This feature is available with premium charts, in some

areas.

You can show static or animated tide and current station

indicators on the Navigation chart or Fishing chart.

From the Navigation or Fishing chart, select Menu > Chart

Setup > Tides & Currents.

Select an option:

• To show current station indicators and tide station

indicators on the chart, select On.

• To show animated tide station indicators and animated

current direction indicators on the chart, select Animated.

Showing Satellite Imagery on the Navigation Chart

NOTE: This feature is available with premium charts, in some

areas.

You can overlay high-resolution satellite images on the land or

on both land and sea portions of the Navigation chart.

NOTE: When enabled, high-resolution satellite images are

present only at lower zoom levels. If you cannot see high-

resolution images in your optional chart region, you can select

to zoom in. You also can set the detail level higher by changing

the map zoom detail.

From the Navigation chart, select Menu > Chart Setup >

Satellite Photos.

Select an option:

• Select Land Only to show standard chart information on

the water, with photos overlaying the land.

• Select Photo Map Blend to show photos on both the

water and the land at a specified opacity. Use the slider

bar to adjust the photo opacity. The higher you set the

percentage, the more the satellite photos cover both land

and water.

Viewing Aerial Photos of Landmarks

Before you can view aerial photos on the Navigation chart, you

must turn on the Satellite Photos setting in the chart setup.

NOTE: This feature is available with premium charts, in some

areas.

You can use aerial photographs of landmarks, marinas, and

harbors to help orient yourself to your surroundings or to

acquaint yourself with a marina or a harbor prior to arrival.

From the Navigation chart, select a camera icon:

• To view an overhead photo, select .

• To view a perspective photo, select . The photo was

taken from the location of the camera, pointed in the

direction of the cone.

Select Aerial Photo.

Automatic Identification System

The Automatic Identification System (AIS) enables you to

identify and track other vessels, and alerts you to area traffic.

When connected to an external AIS device, the chartplotter can

show some AIS information about other vessels that are within

range, that are equipped with a transponder, and that are

actively transmitting AIS information.

The information reported for each vessel includes the Maritime

Mobile Service Identity (MMSI), location, GPS speed, GPS

heading, time that has elapsed since the last position of the

vessel was reported, nearest approach, and time to the nearest

approach.

Some chartplotter models also support Blue Force Tracking.

Vessels being tracked with Blue Force Tracking are indicated on

the chartplotter with a blue-green color.

AIS Targeting Symbols

Symbol Description

AIS vessel. The vessel is reporting AIS information. The

direction in which the triangle is pointing indicates the

direction in which the AIS vessel is moving.

Target is selected.

Target is activated. The target appears larger on the chart. A

green line attached to the target indicates the heading of the

target. The MMSI, speed, and direction of the vessel appear

beneath the target, if the details setting has been set to Show.

If the AIS transmission from the vessel is lost, a message

banner appears.

Charts and 3D Chart Views 5

Symbol Description

Target is lost. A green X indicates that the AIS transmission

from the vessel is lost, and the chartplotter displays a

message banner asking whether the vessel should continue

to be tracked. If you discontinue vessel tracking, the lost

target symbol disappears from the chart or the 3D chart view.

Dangerous target in range. The target flashes while an alarm

sounds and a message banner appears. After the alarm has

been acknowledged, a solid red triangle with a red line

attached to it indicates the location and the heading of the

target. If the safe-zone collision alarm has been set to Off, the

target flashes, but the audible alarm does not sound and the

alarm banner does not appear. If the AIS transmission from

the vessel is lost, a message banner appears.

Dangerous target is lost. A red X indicates that the AIS

transmission from the vessel is lost, and the chartplotter

displays a message banner asking whether the vessel should

continue to be tracked. If you discontinue vessel tracking, the

lost dangerous target symbol disappears from the chart or the

3D chart view.

The location of this symbol indicates the closest point of

approach to a dangerous target, and the numbers near the

symbol indicate the time to the closest point of approach to

that target.

NOTE: Vessels being tracked with the Blue Force Tracking

feature are indicated with a blue-green color regardless of their

status.

Heading and Projected Course of Activated AIS

Targets

When heading and course over ground information are provided

by an activated AIS target, the heading of the target appears on

a chart as a solid line attached to the AIS target symbol. A

heading line does not appear on a 3D chart view.

The projected course of an activated AIS target appears as a

dashed line on a chart or a 3D chart view. The length of the

projected course line is based on the value of the projected

heading setting. If an activated AIS target is not transmitting

speed information, or if the vessel is not moving, a projected

course line does not appear. Changes in the speed, course over

ground, or rate of turn information transmitted by the vessel can

impact the calculation of the projected course line.

When course over ground, heading, and rate of turn information

are provided by an activated AIS target, the projected course of

the target is calculated based on the course over ground and the

rate of turn information. The direction in which the target is

turning, which is also based on the rate of turn information, is

indicated by the direction of the barb at the end of the heading

line. The length of the barb does not change.

When course over ground and heading information are provided

by an activated AIS target, but rate of turn information is not

provided, the projected course of the target is calculated based

on the course over ground information.

Showing AIS Vessels on a Chart or 3D Chart View

Before you can use AIS, you must connect the chartplotter to an

external AIS device and receive active transponder signals from

other vessels.

You can configure how other vessels appear on a chart or on a

3D chart view. The display range configured for one chart or one

3D chart view are applied only to that chart or to that 3D chart

view. The details, projected heading, and trails settings

configured for one chart or one 3D chart view are applied to all

charts and to all 3D chart views.

From a chart or 3D chart view, select Menu > Other Vessels

> Display Setup.

Select an option:

• To indicate the distance from your location in which AIS

vessels appear, select Display Range, and select a

distance.

• To show details about AIS-activated vessels, select

Details > Show.

• To set the projected heading time for AIS-activated

vessels, select Proj. Heading, and enter the time.

• To show the tracks of AIS vessels, select Trails, and

select the length of the track that appears using a trail.

Activating a Target for an AIS Vessel

From a chart or a 3D chart view, select an AIS vessel.

Select AIS Vessel > Activate Target.

Viewing Information about a Targeted AIS Vessel

You can view the AIS signal status, MMSI, GPS speed, GPS

heading, and other information that is reported about a targeted

AIS vessel.

From a chart or a 3D chart view, select an AIS vessel.

Select AIS Vessel.

Deactivating a Target for an AIS Vessel

From a chart or a 3D chart view, select an AIS vessel.

Select AIS Vessel > Deactivate Target.

Viewing a List of AIS Threats

From a chart or 3D chart view, select Menu > Other Vessels

> AIS List.

Setting the Safe-Zone Collision Alarm

Before you can set a safe-zone collision alarm, you must have a

compatible chartplotter connected to an AIS device.

The safe-zone collision alarm is used only with AIS. The safe

zone is used for collision avoidance, and can be customized.

Select Settings > Alarms > AIS > AIS Alarm > On.

A message banner appears and an alarm sounds when an

AIS-activated vessel enters the safe-zone area around your

boat. The object is also labeled as dangerous on the screen.

When the alarm is off, the message banner and audible

alarm are disabled, but the object is still labeled as

dangerous on the screen.

Select Range.

Select a distance for the safe-zone radius around your

vessel.

Select Time To.

Select a time at which the alarm will sound if a target is

determined to intersect the safe zone.

For example, to be notified of a pending intersection 10

minutes before it will likely occur, set Time To to 10, and the

alarm will sound 10 minutes before the vessel intersects the

safe zone.

AIS Distress Signals

Self-contained AIS distress signal devices transmit emergency

position reports when activated. The chartplotter can receive

signals from Search and Rescue Transmitters (SART),

Emergency Position Indicating Radio Beacons (EPIRB), and

other man overboard signals. Distress signal transmissions are

different than standard AIS transmissions, so they appear

differently on the chartplotter. Instead of tracking a distress

signal transmission for collision avoidance, you track a distress

signal transmission to locate and assist a vessel or person.

Navigating to a Distress Signal Transmission

When you receive a distress signal transmission, a distress

signal alarm appears.

Select Review > Go To to begin navigation to the

transmission.

6 Charts and 3D Chart Views

AIS Distress Signal Device Targeting Symbols

Symbol Description

AIS distress signal device transmission. Select to see more

information about the transmission and begin navigation.

Transmission lost.

Transmission test. Appears when a vessel initiates a test of

their distress signal device, and does not represent a true

emergency.

Transmission test lost.

Enabling AIS Transmission Test Alerts

To avoid a large number of test alerts and symbols in crowded

areas such as marinas, you can select to receive or ignore AIS

test messages. To test an AIS emergency device, you must

enable the chartplotter to receive test alerts.

Select Settings > Alarms > AIS.

Select an option:

• To receive or ignore Emergency Position Indicating Radio

Beacon (EPRIB) test signals, select AIS-EPIRB Test.

• To receive or ignore Man Overboard (MOB) test signals,

select AIS-MOB Test.

• To receive or ignore Search and Rescue Transponder

(SART) test signals, select AIS-SART Test.

Turning Off AIS Reception

AIS signal reception is turned on by default.

Select Settings > Other Vessels > AIS > Off.

All AIS functionality on all charts and 3D chart views is

disabled. This includes AIS vessel targeting and tracking,

collision alarms that result from AIS vessel targeting and

tracking, and the display of information about AIS vessels.

Chart and 3D Chart View Settings

NOTE: Not all settings apply to all charts and 3D chart views.

Some options require premium maps or connected accessories,

such as radar.

These settings apply to the charts and 3D chart views, except

the radar overlay and Fish Eye 3D (Fish Eye 3D Settings).

From a chart or a 3D chart view, select Menu.

Waypoints & Tracks: See Waypoints and Tracks Settings on

the Charts and Chart Views.

Other Vessels: See Other Vessels Settings on the Charts and

Chart Views.

Surface Radar: Shows surface radar details on the Perspective

3D or Mariner's Eye 3D chart views.

Weather Radar: Shows weather radar imaging on the

Perspective 3D or Mariner's Eye 3D chart views.

Navaids: Shows navigational aids on the Fishing chart.

Laylines: Adjusts the laylines, when in sailing mode (Laylines

Settings).

Chart Setup: See Navigation and Fishing Chart Setup.

Overlay Numbers: See Overlay Numbers Settings. This might

appear in the Chart Setup menu.

Chart Appearance: See Chart Appearance Settings. This might

appear in the Chart Setup menu.

Navigation and Fishing Chart Setup

NOTE: Not all settings apply to all charts and 3D chart views.

Some settings require external accessories or applicable

premium charts.

From the Navigation chart or Fishing chart, select Menu > Chart

Setup.

Satellite Photos: Shows high-resolution satellite images on the

land or on both land and sea portions of the Navigation chart,

when certain premium maps are used Showing Satellite

Imagery on the Navigation Chart.

Water Overlay: Enables relief shading, which shows the

gradient of the bottom with shading, or sonar imagery, which

helps identify the density of the bottom. This feature is

available only with some premium maps.

Tides & Currents: Shows current station indicators and tide

station indicators on the chart Showing Tides and Current

Indicators and enables the tides and current slider, which

sets the time for which tides and currents are reported on the

map.

Roses: Shows a compass rose around your boat, indicating

compass direction oriented to the heading of the boat. A true

wind direction or apparent wind direction indicator appears if

the chartplotter is connected to a compatible marine wind

sensor. When in sailing mode, true and apparent wind are

shown on the wind rose.

Lake Level: Sets the present water level of the lake. This

feature is available only with some premium maps.

Overlay Numbers: See Overlay Numbers Settings.

Weather: Sets which weather items are shown on the chart,

when the chartplotter is connected to a compatible weather

receiver with an active subscription. Requires a compatible,

connected antenna and an active subscription.

Chart Appearance: See Chart Appearance Settings.

Waypoints and Tracks Settings on the Charts and

Chart Views

From a chart or a 3D chart view, select Menu > Waypoints &

Tracks.

Tracks: Shows tracks on the chart or 3D chart view.

Waypoints: Shows the list of waypoints (Viewing a List of all

Waypoints).

New Waypoint: Creates a new waypoint.

Waypoint Display: Sets how to display waypoints on the chart.

Active Tracks: Shows the active track options menu.

Saved Tracks: Shows the list of saved tracks (Viewing a List of

Saved Tracks).

Tracks Display: Sets which tracks to display on the chart based

on track color.

Laylines Settings

When in sailing mode (Setting the Vessel Type), you can display

laylines on the navigation chart. Laylines can be very helpful

when racing.

From the navigation chart, select Menu > Sailing > Laylines.

Display: Sets how the laylines and vessel are shown on the

chart, and sets the length of the laylines.

Sailing Angle: Allows you to select how the device calculates

laylines. The Actual option calculates the laylines using the

measured wind angle from the wind sensor. The Manual

option calculates the laylines using manually entered

windward and leeward angles.

Tide Correction: Corrects the laylines based on the tide.

Overlay Numbers Settings

From a chart, 3D chart view, the Radar screen, or a

Combinations screen, select Menu > Overlay Numbers.

Edit Layout: Sets the layout of the data overlay, or data fields.

You can select the data to be shown within each data field.

Navigation Inset: Shows the navigation inset when the vessel

is navigating to a destination.

Navigation Inset Setup: Allows you to configure the navigation

inset to show Route Leg Details, and to control when the

inset appears before a turn or destination.

Charts and 3D Chart Views 7

Compass Tape: Shows the compass tape data bar when the

vessel is navigating to a destination.

Editing the Data Fields

You can change the data shown in the overlay numbers

displayed on the charts and other screens.

From a screen that supports overlay numbers, select Menu.

If necessary, select Chart Setup.

Select Overlay Numbers > Edit Layout.

Select a layout.

Select a data field.

Select the type of data shown in the field.

Available data options vary based on the chartplotter and

network configuration.

Showing a Navigation Inset

You can control whether a navigation inset appears on some

chart views. The navigation inset is shown only when the boat is

navigating to a destination.

From a chart or 3D chart view, select Menu.

If necessary, select Chart Setup.

Select Overlay Numbers > Navigation Inset > Auto.

Select Navigation Inset Setup.

Complete an action:

• To show waypoint velocity made good (VMG) when

navigating a route with more than one leg, select Route

Leg Details > On.

• To show next-turn data based on distance, select Next

Turn > Distance.

• To show next-turn data based on time, select Next Turn >

Time.

• To indicate how the destination data appears, select

Destination, and select an option.

Chart Appearance Settings

You can adjust the appearance of the different charts and 3D

chart views. Each setting is specific to the chart or chart view

being used.

NOTE: Not all settings apply to all charts and 3D chart views

and chartplotter models. Some options require premium maps or

connected accessories.

From a chart or 3D chart view, select Menu > Chart Setup >

Chart Appearance.

Orientation: Sets the perspective of the map.

Detail: Adjusts the amount of detail shown on the map, at

different zoom levels.

Heading Line: Shows and adjusts the heading line, which is a

line drawn on the map from the bow of the boat in the

direction of travel, and sets the data source for the heading

line.

World Map: Uses either a basic world map or a shaded relief

map on the chart. These differences are visible only when

zoomed out too far to see the detailed charts.

Spot Depths: Turns on spot soundings and sets a dangerous

depth. Spot depths that are equal to or more shallow than the

dangerous depth are indicated by red text.

Safety Shading: Sets the shades from the shoreline to the

specified depth.

Depth Range Shading: Specifies an upper and lower depth to

shade between.

Symbols: Shows and configures the appearance of various

symbols on the chart, such as the vessel icon, navaid

symbols, land POIs, and light sectors.

Style: Sets how the chart appears over 3D terrain.

Hazard Colors: Shows shallow water and land with a color

scale. Blue indicates deep water, yellow is shallow water, and

red is very shallow water.

Safe Depth: Sets the appearance of a safe depth for the

Mariner’s Eye 3D chart view.

NOTE: This setting affects only the appearance of hazard

colors for the Mariner’s Eye 3D chart view. It does not affect

the safe water depth Auto Guidance setting or the sonar

shallow water alarm setting.

Range Rings: Shows and configures the appearance of range

rings, which help you to visualize distances in some chart

views.

Lane Width: Specifies the width of the navigation lane, which is

the magenta line in some chart views that indicates the

course to your destination.

Setting the Heading and Course Over Ground Lines

You can show the heading line and the course over ground

(COG) line on the chart.

COG is your direction of movement. Heading is the direction the

bow of the boat is pointed, when a heading sensor is connected.

From a chart view, select Menu > Chart Setup > Chart

Appearance > Heading Line.

If necessary, select Source, and select an option:

• To automatically use the source available, select Auto.

• To use the GPS antenna heading for COG, select GPS

Heading (COG).

• To use data from a connected heading sensor, select

Heading.

• To use data from both a connected heading sensor and

the GPS antenna, select COG and Heading.

This displays both the heading line and the COG line on

the chart.

Select Display, and select an option:

• Select Distance > Distance, and enter the length of the

line shown on the chart.

• Select Time > Time, and enter the time used to calculate

the distance your boat will travel in the specified time at

your present speed.

Other Vessels Settings on the Charts and Chart Views

NOTE: These options require connected accessories, such as

an AIS receiver or VHF radio.

From a chart or 3D chart view, select Menu > Other Vessels.

AIS List: Shows the AIS list (Viewing a List of AIS Threats).

DSC List: Shows the DSC list (DSC List).

Display Setup: See AIS Display Settings.

DSC Trails: Shows the tracks of DSC vessels, and selects the

length of the track that appears using a trail.

AIS Alarm: Sets the safe-zone collision alarm (Setting the Safe-

Zone Collision Alarm).

AIS Display Settings

NOTE: AIS requires the use of an external AIS device and

active transponder signals from other vessels.

From a chart or 3D chart view, select Menu > Other Vessels >

Display Setup.

AIS Display Range: Indicates the distance from your location

within which AIS vessels appear.

Details: Shows details about AIS-activated vessels.

Proj. Heading: Sets the projected heading time for AIS-

activated vessels.

Trails: Shows the tracks of AIS vessels, and select the length of

the track that appears using a trail.

8 Charts and 3D Chart Views

Fish Eye 3D Settings

NOTE: This feature is available with premium charts, in some

areas.

From the Fish Eye 3D chart view, select Menu.

View: Sets the perspective of the 3D chart view.

Tracks: Shows tracks.

Sonar Cone: Shows a cone that indicates the area covered by

the transducer.

Fish Symbols: Shows suspended targets.

Navigation with a Chartplotter

CAUTION

If your vessel has an autopilot system, a dedicated autopilot

control display must be installed at each steering helm in order

to disable the autopilot system.

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

When using Go To, a direct course and a corrected course may

pass over land or shallow water. Use visual sightings, and steer

to avoid land, shallow water, and other dangerous objects.

NOTE: Auto Guidance is available with premium charts, in some

areas.

NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are

available with premium charts, in some areas.

NOTE: The offshore Fishing chart is available with premium

charts, in some areas.

To navigate, you must choose a destination, set a course or

create a route, and follow the course or route. You can follow

the course or the route on the Navigation chart, Fishing chart,

Perspective 3D chart view, or Mariner’s Eye 3D chart view.

You can set and follow a course to a destination using one of

three methods: Go To, Route To, or Auto Guidance.

Go To: Takes you directly to the destination. This is the

standard option for navigating to a destination. The

chartplotter creates a straight-line course or navigation line to

the destination. The path may run over land and other

obstacles.

Route To: Creates a route from your location to a destination,

allowing you to add turns along the way. This option provides

a straight-line course to the destination, but allows you to add

turns into the route to avoid land and other obstacles.

Auto Guidance: Creates a path to a destination using Auto

Guidance. This option is available only when using a

compatible premium chart in a compatible chartplotter. It

provides a turn-by-turn navigation line to the destination,

avoiding land and other obstacles. The navigation line is

based on the chart data and the safe depth, safe height, and

shoreline distance user-defined chartplotter settings. Using

these settings and chart data, the chartplotter creates a

navigation line that avoids all areas that cannot be navigated

between the present location and the destination.

When you are using a compatible Garmin autopilot

connected to the chartplotter using NMEA 2000

, the

autopilot follows the Auto Guidance route.

Basic Navigation Questions

Question Answer

How do I make the chartplotter

point me in the direction in

which I want to go (bearing)?

Navigate using Go To. See Setting

and Following a Direct Course Using

Go To.

How do I make the device

guide me along a straight line

(minimizing cross track) to a

location using the shortest

distance from the present

location?

Build a single-leg route and navigate it

using Route To. See Creating and

Navigating a Route From Your Present

Location.

How do I make the device

guide me to a location while

avoiding charted obstacles?

Build a multi-leg route and navigate it

using Route To. See Creating and

Navigating a Route From Your Present

Location.

How do I make the device

steer my automatic pilot?

Navigate using Route To. See

Creating and Navigating a Route From

Your Present Location.

Can the device create a path

for me?

If you have premium maps that

support Auto Guidance and are in an

area covered by Auto Guidance,

navigate using Auto Guidance. See

Setting and Following an Auto

Guidance Path.

How do I change the Auto

Guidance settings for my boat?

See Auto Guidance Line

Configurations.

Destinations

You can select destinations using various charts and 3D chart

views or using the lists.

Searching for a Destination by Name

You can search for saved waypoints, saved routes, saved

tracks, and marine services destinations by name.

Select Nav Info > Search by Name.

Enter at least a portion of the name of your destination.

If necessary, select Done.

The 50 nearest destinations that contain your search criteria

appear.

Select the destination.

Selecting a Destination Using the Navigation Chart

From the Navigation chart, select a destination.

Searching for a Marine Services Destination

NOTE: This feature is available with premium charts, in some

areas.

The chartplotter contains information for thousands of

destinations offering marine services.

Select Nav Info.

Select Offshore Services or Inland Services.

If necessary, select the marine service category.

The chartplotter shows a list of the nearest locations and the

distance and bearing to each.

Select a destination.

You can select or to view additional information or to

show the location on a chart.

Stopping Navigation

From the Navigation chart or Fishing chart, select Menu >

Stop Navigation.

Waypoints

Waypoints are locations you record and store in the device.

Marking Your Present Location as a Waypoint

From any screen, select Mark.

Navigation with a Chartplotter 9

Creating a Waypoint at a Different Location

Select Nav Info > Waypoints > New Waypoint.

Select an option:

• To create the waypoint by entering position coordinates,

select Enter Coordinates, and enter the coordinates.

• To create the waypoint using a chart, select Use Chart,

select the location, and select Select.

Marking and Starting Navigation to an MOB Location

When you mark a waypoint, you can designate it as a man

overboard (MOB) location.

Select an option:

• From any screen, select Mark > Man Overboard.

• From the Home screen, select Man Overboard > Yes.

An international MOB symbol marks the active MOB point and

the chartplotter sets a direct course back to the marked location.

Viewing a List of all Waypoints

Select Nav Info > Waypoints.

Editing a Saved Waypoint

Select Nav Info > Waypoints.

Select a waypoint.

Select Edit Waypoint.

Select an option:

• To add a name, select Name, and enter a name.

• To change the symbol, select Symbol.

• To change the depth, select Depth.

• To change the water temperature, select Water Temp..

• To change the comment, select Comment.

• To move the position of the waypoint, select Move.

Moving a Saved Waypoint

Select Nav Info > Waypoints.

Select a waypoint.

Select Edit Waypoint > Move.

Indicate a new location for the waypoint:

• To move the waypoint while using the chart, select Use

Chart, select a new location on the chart, and select

Move Waypoint.

• To move the waypoint using coordinates, select Enter

Coordinates, and enter the new coordinates.

Browsing for and Navigating to a Saved Waypoint

CAUTION

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

When using Go To, a direct course and a corrected course may

pass over land or shallow water. Use visual sightings, and steer

to avoid land, shallow water, and other dangerous objects.

NOTE: Auto Guidance is available with premium charts, in some

areas.

Before you can navigate to a waypoint, you must create a

waypoint.

Select Nav Info > Waypoints.

Select a waypoint.

Select Navigate To.

Select an option:

• To navigate directly to the location, select Go To.

• To create a route to the location, including turns, select

Route To.

• To use Auto Guidance, select Auto Guidance.

Review the course indicated by the magenta line.

NOTE: When using Auto Guidance, a gray segment within

any part of the magenta line indicates that Auto Guidance

cannot calculate part of the Auto Guidance line. This is due to

the settings for minimum safe water depth and minimum safe

obstacle height.

Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

Deleting a Waypoint or an MOB

Select Nav Info > Waypoints.

Select a waypoint or an MOB.

Select Delete.

Deleting All Waypoints

Select Nav Info > Manage Data > Clear User Data >

Waypoints > All.

Setting and Following a Direct Course Using Go To

CAUTION

When using Go To, a direct course and a corrected course may

pass over land or shallow water. Use visual sightings, and steer

to avoid land, shallow water, and other dangerous objects.

You can set and follow a direct course from your current location

to a selected destination.

Select a destination (Destinations).

Select Navigate To > Go To.

A magenta line appears. In the center of the magenta line is

a thinner purple line that represents the corrected course

from your current location to the destination. The corrected

course is dynamic, and it moves with your boat when you are

off course.

Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

If you are off course, follow the purple line (corrected course)

to go to your destination, or steer back to the magenta line

(direct course).

Routes

Creating and Navigating a Route From Your Present

Location

You can create and immediately navigate a route on the

Navigation chart or the Fishing chart. This procedure does not

save the route or the waypoint data.

NOTE: The offshore Fishing chart is available with premium

charts, in some areas.

From the Navigation chart or Fishing chart, select a

destination.

Select Navigate To > Route To.

Select the location of the last turn before the destination.

Select Add Turn.

If necessary, repeat step 3 and 4 to add additional turns,

working backward from the destination to the present location

of your vessel.

The last turn you add should be the first turn you make,

starting from your present location. It should be the turn

closest to your vessel.

If necessary, select Menu.

Select Navigate Route.

Review the course indicated by the magenta line.

10 Navigation with a Chartplotter

Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

Creating and Saving a Route

This procedure saves the route and all the waypoints in it. The

starting point can be your present location or another location.

Select Nav Info > Routes & Auto Guidance Paths > New

Route > Route Using Chart.

Select the starting location of the route.

Select Add Turn.

Select the location of the next turn on the chart.

Select Add Turn.

The chartplotter marks the location of the turn with a

waypoint.

If necessary, repeat steps 4 and 5 to add more turns.

Select the final destination.

Viewing a List of Routes and Auto Guidance Paths

Select Nav Info > Routes & Auto Guidance Paths.

If necessary, select Filter to see routes only or Auto

Guidance paths only.

Editing a Saved Route

You can change the name of a route or change the turns the

route contains.

Select Nav Info > Routes & Auto Guidance Paths.

Select a route.

Select Edit Route.

Select an option:

• To change the name, select Name, and enter the name.

• To select a waypoint from the turn list, select Edit Turns >

Use Turn List, and select a waypoint from the list.

• To select a turn using the chart, select Edit Turns > Use

Chart, and select a location on the chart.

Browsing for and Navigating a Saved Route

Before you can browse a list of routes and navigate to one of

them, you must create and save at least one route.

Select Nav Info > Routes & Auto Guidance Paths.

Select a route.

Select Navigate To.

Select an option:

• To navigate the route from the starting point used when

the route was created, select Forward.

• To navigate the route from the destination point used

when the route was created, select Backward.

A magenta line appears. In the center of the magenta line is

a thinner purple line that represents the corrected course

from your present location to the destination. The corrected

course is dynamic, and it moves with your boat when you are

off course.

Review the course indicated by the magenta line.

Follow the magenta line along each leg in the route, steering

to avoid land, shallow water, and other obstacles.

If you are off course, follow the purple line (corrected course)

to go to your destination, or steer back to the magenta line

(direct course).

Browsing for and Navigating Parallel to a Saved

Route

Before you can browse a list of routes and navigate to one of

them, you must create and save at least one route.

Select Nav Info > Routes & Auto Guidance Paths.

Select a route.

Select Navigate To.

Select Offset to navigate parallel to the route, offset from it

by a specific distance.

Indicate how to navigate the route:

• To navigate the route from the starting point used when

the route was created, to the left of the original route,

select Forward – Port.

• To navigate the route from the starting point used when

the route was created, to the right of the original route,

select Forward – Starboard.

• To navigate the route from the destination point used

when the route was created, to the left of the original

route, select Backward – Port.

• To navigate the route from the destination point used

when the route was created, to the right of the original

route, select Backward – Starboard.

If necessary, select Done.

A magenta line appears. In the center of the magenta line is

a thinner purple line that represents the corrected course

from your present location to the destination. The corrected

course is dynamic, and it moves with your boat when you are

off course.

Review the course indicated by the magenta line.

Follow the magenta line along each leg in the route, steering

to avoid land, shallow water, and other obstacles.

If you are off course, follow the purple line (corrected course)

to go to your destination, or steer back to the magenta line

(direct course).

Deleting a Saved Route

Select Nav Info > Routes & Auto Guidance Paths.

Select a route.

Select Review > Delete.

Deleting All Saved Routes

Select Nav Info > Manage Data > Clear User Data >

Routes & Auto Guidance Paths.

Auto Guidance

CAUTION

The Auto Guidance feature is based on electronic chart

information. That data does not ensure obstacle and bottom

clearance. Carefully compare the course to all visual sightings,

and avoid any land, shallow water, or other obstacles that may

be in your path.

NOTE: Auto Guidance is available with premium charts, in some

areas.

You can use Auto Guidance to plot the best path to your

destination. Auto Guidance uses your chartplotter to scan chart

data, such as water depth and known obstacles, to calculate a

suggested path. You can adjust the path during navigation.

Setting and Following an Auto Guidance Path

Select a destination (Destinations).

Select Navigate To > Auto Guidance.

Review the path, indicated by the magenta line.

Select Start Navigation.

Follow the magenta line, steering to avoid land, shallow

water, and other obstacles.

NOTE: When using Auto Guidance, a gray segment within

any part of the magenta line indicates that Auto Guidance

cannot calculate part of the Auto Guidance line. This is due to

the settings for minimum safe water depth and minimum safe

obstacle height.

Navigation with a Chartplotter 11

Creating and Saving an Auto Guidance Path

Select Nav Info > Routes & Auto Guidance Paths > New

Route > Auto Guidance.

Select a starting point, and select Next.

Select a destination, and select Next.

Select an option:

• To view a hazard and adjust the path near a hazard,

select Hazard Review.

• To adjust the path, select Adjust Path, and follow the on-

screen instructions.

• To delete the path, select Cancel Auto Guidance.

• To save the path, select Done.

Adjusting an Auto Guidance Path

From the Navigation chart, follow the on-screen instructions

or use the arrow keys to move the destination point to the

new location.

Select Select > Move Point.

Select Back to return to the navigation screen.

Canceling an Auto Guidance Calculation in Progress

From the Navigation chart, select Menu > Cancel.

TIP: You can select Back to quickly cancel the calculation.

Setting a Timed Arrival

You can use this feature on a route or an Auto Guidance path to

get feedback about when you should arrive at a selected point.

This allows you to time your arrival at a location, such as a

bridge opening or a race starting line.

From the Navigation chart, select Menu.

If necessary, select Navigation Options.

Select Timed Arrival.

TIP: You can quickly open the Timed Arrival menu by

selecting a point on the path or route.

Auto Guidance Line Configurations

CAUTION

The Safe Depth and Safe Height settings influence how the

chartplotter calculates an Auto Guidance line. If an area has an

unknown water depth or an unknown obstacle height, the Auto

Guidance line is not calculated in that area. If an area at the

beginning or the end of an Auto Guidance line is shallower than

the safe water depth or lower than the safe obstacle height, the

Auto Guidance line is not calculated in that area. On the chart,

the course through those areas appears as a gray line. When

your boat enters one of those areas, a warning message

appears.

NOTE: Auto Guidance is available with premium charts, in some

areas.

You can set the parameters the chartplotter uses when

calculating an Auto Guidance line.

Safe Depth: Sets the minimum depth (chart depth datum) the

chartplotter uses when calculating an Auto Guidance line.

NOTE: The minimum safe depth for the premium charts is 3

feet. If you enter a Safe Depth value of less than 3 feet, the

charts only use depths of 3 feet for Auto Guidance route

calculations.

Safe Height: Sets the minimum height (chart height datum) of a

bridge that your boat can safely travel under.

Shoreline Distance: Sets how close to the shore you want the

Auto Guidance line to be placed. The Auto Guidance line

may move if you change this setting while navigating. The

available values for this setting are relative, not absolute. To

ensure that the Auto Guidance line is placed the appropriate

distance from shore, you can assess the placement of the

Auto Guidance line using one or more familiar destinations

that require navigation through a narrow waterway (Adjusting

the Distance from Shore).

Adjusting the Distance from Shore

The Shoreline Distance setting indicates how close to the shore

you want the Auto Guidance line to be placed. The Auto

Guidance line may move if you change this setting while

navigating. The available values for the Shoreline Distance

setting are relative, not absolute. To ensure the Auto Guidance

line is placed the appropriate distance from shore, you can

assess the placement of the Auto Guidance line using one or

more familiar destinations that require navigation through a

narrow waterway.

Dock your vessel or drop the anchor.

Select Settings > Navigation > Auto Guidance > Shoreline

Distance > Normal.

Select a destination that you have navigated to previously.

Select Navigate To > Auto Guidance.

Review the placement of the Auto Guidance line, and

determine whether the line safely avoids known obstacles

and the turns enable efficient travel.

Select an option:

• If the placement of the Auto Guidance line is satisfactory,

select Menu > Stop Navigation, and proceed to step 10.

• If the Auto Guidance line is too close to known obstacles,

select Settings > Navigation > Auto Guidance >

Shoreline Distance > Far.

• If the turns in the Auto Guidance line are too wide, select

Settings > Navigation > Auto Guidance > Shoreline

Distance > Near.

If you selected Near or Far in step 6, review the placement of

the Auto Guidance line, and determine whether the line

safely avoids known obstacles and the turns enable efficient

travel.

Auto Guidance maintains a wide clearance from obstacles in

open water, even if you set the Shoreline Distance setting to

Near or Nearest. As a result, the chartplotter may not

reposition the Auto Guidance line, unless the destination

selected requires navigation through a narrow waterway.

Select an option:

• If the placement of the Auto Guidance line is satisfactory,

select Menu > Stop Navigation, and proceed to step 10.

• If the Auto Guidance line is too close to known obstacles,

select Settings > Navigation > Auto Guidance >

Shoreline Distance > Farthest.

• If the turns in the Auto Guidance line are too wide, select

Settings > Navigation > Auto Guidance > Shoreline

Distance > Nearest.

If you selected Nearest or Farthest in step 8, review the

placement of the Auto Guidance line, and determine

whether the line safely avoids known obstacles and the turns

enable efficient travel.

Auto Guidance maintains a wide clearance from obstacles in

open water, even if you set the Shoreline Distance setting to

Near or Nearest. As a result, the chartplotter may not

reposition the Auto Guidance line, unless the destination

selected requires navigation through a narrow waterway.

Repeat steps 3 through 9 at least once more, using a

different destination each time, until you are familiar with the

functionality of the Shoreline Distance setting.

Tracks

A track is a recording of the path of your boat. The track

currently being recorded is called the active track, and it can be

saved. You can show tracks in each chart or 3D chart view.

12 Navigation with a Chartplotter

Showing Tracks

From a chart or a 3D chart view, select Menu > Waypoints &

Tracks > Tracks > On.

A trailing line on the chart indicates your track.

Setting the Color of the Active Track

Select Nav Info > Tracks > Active Track Options > Track

Color.

Select a track color.

Saving the Active Track

The track currently being recorded is called the active track.

Select Nav Info > Tracks > Save Active Track.

Select an option:

• Select the time the active track began.

• Select Entire Log.

Select Save.

Viewing a List of Saved Tracks

Select Nav Info > Tracks > Saved Tracks.

Editing a Saved Track

Select Nav Info > Tracks > Saved Tracks.

Select a track.

Select Edit Track.

Select an option:

• Select Name, and enter the new name.

• Select Track Color, and select a color.

Saving a Track as a Route

Select Nav Info > Tracks > Saved Tracks.

Select a track.

Select Edit Track > Save Route.

Browsing for and Navigating a Recorded Track

Before you can browse a list of tracks and navigate to them, you

must record and save at least one track (Tracks).

Select Nav Info > Tracks > Saved Tracks.

Select a track.

Select Follow Track.

Select an option:

• To navigate the track from the starting point used when

the track was created, select Forward.

• To navigate the track from the destination point used

when the track was created, select Backward.

Review the course indicated by the colored line.

Follow the line along each leg in the route, steering to avoid

land, shallow water, and other obstacles.

Deleting a Saved Track

Select Nav Info > Tracks > Saved Tracks.

Select a track.

Select Delete.

Deleting All Saved Tracks

Select Nav Info > Manage Data > Clear User Data > Saved

Tracks.

Retracing the Active Track

The track currently being recorded is called the active track.

Select Nav Info > Tracks > Follow Active Track.

Select an option:

• Select the time the active track began.

• Select Entire Log.

Review the course indicated by the colored line.

Follow the colored line, steering to avoid land, shallow water,

and other obstacles.

Clearing the Active Track

Select Nav Info > Manage Data > Tracks > Clear Active

Track.

The track memory is cleared, and the active track continues

to be recorded.

Managing the Track Log Memory During Recording

Select Nav Info > Tracks > Active Track Options.

Select Record Mode.

Select an option:

• To record a track log until the track memory is full, select

Fill.

• To continuously record a track log, replacing the oldest

track data with new data, select Wrap.

Configuring the Recording Interval of the Track Log

You can indicate the frequency at which the track plot is

recorded. Recording more frequent plots is more accurate but

fills the track log faster. The resolution interval is recommended

for the most efficient use of memory.

Select Nav Info > Tracks > Active Track Options > Record

Interval > Interval.

Select an option:

• To record the track based on a distance between points,

select Distance > Change, and enter the distance.

• To record the track based on a time interval, select Time >

Change, and enter the time interval.

• To record the track plot based on a variance from your

course, select Resolution > Change, and enter the

maximum error allowed from the true course before

recording a track point.

Stopping Navigation

While navigating, from the Navigation or Fishing chart, select

an option:

• Select Menu > Stop Navigation.

• When navigating with Auto Guidance, select Menu >

Navigation Options > Stop Navigation.

Synchronizing User Data Across the Garmin

Marine Network

NOTICE

Before you synchronize the user data across the network, you

should backup your user data to prevent possible data loss. See

Backing Up Data to a Computer.

You can share waypoints, tracks, and routes with all compatible

devices connected to the Garmin Marine Network (Ethernet)

automatically.

NOTE: This feature is not available on all models.

Select Nav Info > Manage Data > User Data Sharing > On.

If a change is made to a waypoint, track, or route on one

chartplotter, that data is synchronized automatically across all

chartplotters on the Ethernet network.

Deleting All Saved Waypoints, Routes, and

Tracks

Select Nav Info > Manage Data > Clear User Data > All >

OK.

Navigation with a Chartplotter 13

Combinations

The Combination screen shows a combination of different

screens at the same time. The number of options available on

the Combination screen depends on the optional devices you

have connected to your chartplotter and whether you are using

premium maps.

Selecting a Combination

Select Combinations.

Select a combination.

Customizing a Combination Screen

Not all options are available on all chartplotter models.

Select Combinations.

Select a combination.

Select Menu > Edit Combination.

Select an option:

• To change the name, select Name, and enter a new

name.

• To change the number of windows shown in the

combination screen, select Functions, and select the new

number.

• To change the split orientation, select Split.

• To customize the numbers shown on the screen, select

Overlay Numbers.

• To change the data shown in the combination, select the

screen to change, and select the new data.

• To resize the windows, drag the arrows.

Adding a Custom Combination Screen

You can create a custom combination screen to suit your needs.

Select Combinations > Menu > Add.

Select an option:

• To change the name, select Name, enter a new name,

and select Done.

• To change the number of functions shown, select

Functions, and select a number.

• To change the function of the portion of the screen, select

the area to change, and select a function from the list on

the right.

• To change the vertical or horizontal split orientation of a

multi-function display, select Split, and select an option.

• To change how data appears on the page, select Overlay

Numbers, and select an option.

• To change the type of data shown, select Overlay

Numbers, select a data field, and select the new data

type.

Sonar

When properly connected to an optional Garmin sounder

module and a transducer, your compatible chartplotter can be

used as a fishfinder. There are different sonar views to help you

view the fish in the area.

The adjustments you can make to each sonar view vary

depending on the view you are in and the chartplotter model,

sounder module, and transducer you have connected.

Sonar Views

The sonar views available vary depending on the type of

transducer and optional sounder module connected to the

chartplotter. For example, you can view the Split Frequency

view only if you have a dual-frequency transducer connected.

There are four basic styles of sonar views available: a full-

screen view, a split-screen view that combines two or more

views, a split-zoom view, and a split-frequency view that

displays two different frequencies. You can customize the

settings for each view in the screen. For example, if you are

viewing the split-frequency view, you can adjust the gain for

each of the frequencies separately.

If you do not see an arrangement of sonar views to suit your

needs, you can create a custom screen (xx).

Traditional Sonar View

There are several full-screen views available, depending on the

equipment connected.

The full-screen Traditional sonar view show a large image of the

sonar readings from a transducer. The range scale along the

right side of the screen shows the depth of detected objects as

the screen scrolls from the right to the left.

Depth information

Suspended targets or fish

Bottom of the body of water

DownVü Sonar View

NOTE: Not all models support DownVü sonar technology and

transducers.

NOTE: To receive DownVü scanning sonar, you need a

compatible chartplotter or fishfinder and a compatible

transducer.

DownVü high-frequency sonar provides a clearer picture below

the boat, providing a more detailed representation of structures

the boat is passing over.

Traditional transducers emit a conical beam. The DownVü

scanning sonar technology emits a narrow beam, similar to the

shape of the beam in a copying machine. This beam provides a

clearer, picture-like image of what is beneath the boat.

SideVü Sonar View

NOTE: Not all models support SideVü sonar and scanning

transducers.

NOTE: To receive SideVü scanning sonar, you need a

compatible chartplotter, a compatible sounder module, and a

compatible transducer.

SideVü scanning sonar technology shows you a picture of what

lies to the sides of the boat. You can use this as a search tool to

find structures and fish.

Left side of the boat

Right side of the boat

14 Combinations

Page is loading ...

Garmin 500-PRO-1 Owner's manual

Brand: Garmin

Model: 500-PRO-1

Category: Navigators

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Garmin 500-PRO-1 Owner's manual

This manual is also suitable for

Garmin 500-PRO-1 Owner's manual

Related papers

Other documents