Watlow Electric EZ-ZONE PM User guide

Brand: Watlow Electric

Model: EZ-ZONE PM

Category: Recording Equipment

Type: User guide

This manual is also suitable for

EZ-ZONE PM Express

0600-0065-0000 Rev. E Made in the U.S.A.

April 2013

EZ-ZONE

PM Express

User's Guide

Registered Company

Winona, Minnesota USA

ISO 9001

TOTAL

3 Year Warranty

CUSTOMER

SATISFACTION

PID Controller

1241 Bundy Boulevard., Winona, Minnesota USA 55987

Phone: +1 (507) 454-5300, Fax: +1 (507) 452-4507 http://www.watlow.com

EZ-ZONE PM Express (PID) • 2 •

Safety Information

We use note, caution and warning symbols throughout this book to draw your attention to important operational

and safety information.

A “NOTE” marks a short message to alert you to an important detail.

A “CAUTION” safety alert appears with information that is important for protecting your equipment and perfor-

mance. Be especially careful to read and follow all cautions that apply to your application.

A “WARNING” safety alert appears with information that is important for protecting you, others and equipment

from damage. Pay very close attention to all warnings that apply to your application.

The electrical hazard symbol, (a lightning bolt in a triangle) precedes an electric shock hazard CAUTION or

WARNING safety statement. Further explanations follow:

Symbol Explanation

CAUTION – Warning or Hazard that needs further explanation than label on unit can

provide. Consult users manual for further information.

ESD Sensitive product, use proper grounding and handling techniques when installing or

servicing product.

Unit protected by double/reinforced insulation for shock hazard prevention.

Do not throw in trash, use proper recycling techniques or consult manufacturer for proper

disposal.

Unit can be powered with either alternating current (ac) voltage or direct current (dc)

voltage.

Unit is a Listed device per Underwriters Laboratories®. It has been evaluated to United

States and Canadian requirements for Process Control Equipment. UL 61010 and CSA

C22.2 No. 61010. File E185611 QUYX, QUYX7. See: www.ul.com

Unit is a Listed device per Underwriters Laboratories®. It has been evaluated to United

States and Canadian requirements for Hazardous Locations Class 1 Division II Groups A,

B, C and D. ANSI/ISA 12.12.01-2007. File E184390 QUZW, QUZW7. See: www.ul.com

Unit is compliant with European Union directives. See Declaration of Conformity for

further details on Directives and Standards used for Compliance.

Unit has been reviewed and approved by Factory Mutual as a Temperature Limit Device per

FM Class 3545 standard. See: www.fmglobal.com

Unit has been reviewed and approved by CSA International for use as Temperature

Indicating-Regulating Equipment per CSA C22.2 No. 24. See: www.csa-international.org

Warranty

This EZ-ZONE

PM is manufactured by ISO 9001 registered processes and is backed by a three year warranty to

the first purchaser for use, providing that the units have not been misapplied. Watlow's obligations hereunder, at

Watlow's option, are limited to replacement, repair or refund of purchase price, and parts which upon examina-

tion prove to be defective within the warranty period specified. This warranty does not apply to damage resulting

from transportation, alteration, misuse or abuse. The purchaser must use Watlow parts to maintain all listed

ratings.

EZ-ZONE PM Express (PID) • 3 •

Technical Assistance

You can get assistance from your local Watlow representative (see back cover), send an e-mail with your ques-

tions to: [email protected] or dial +1 (507) 494-5656 between 7 a.m. and 5 p.m. Central Standard

Time (CST) and ask for an Applications Engineer. Please have the following information available when calling:

• Complete model number

• All configuration information

• User's Guide

• Factory Page

The EZ-ZONE PM Controller User’s Guide is copyrighted by Watlow Electric, Inc., © April 2013 with all rights

reserved. The EZ-ZONE PM is covered by U.S. Patent No. 6,005,577 and Patents Pending

Product Overview

The EZ-ZONE PM Express single loop PID controller is available in 1/4, 8

, 16

or 32

DIN panel-mount pack-

ages. Ordering options include high or low voltage units with up to two outputs.

EZ-ZONE PM Express (PID) • 4 • Install and Wire

Installation and Wiring

1/32 DIN (PM3) Recommended Panel Spacing

Side

Front

Top

15.9 mm

(0.63 in)

101.6 mm

(4.00 in)

31.2 mm

(1.23 in)

53.3 mm

(2.10 in)

30.9 mm

(1.22 in)

45.2 mm

(1.78 in)

22.4 mm

(0.88 in)

21.6 mm

(0.85 in)

21.6 mm

(0.85 in)

panel thickness 1.53 to 9.52 mm

(0.060 to 0.075 in)

1/32 DIN (PM3) Dimensions

EZ-ZONE PM Express (PID) • 5 • Install and Wire

Side

Front

Top

15.8 mm

(0.62 in)

101.6 mm

(4.00 in)

51.2 mm

(2.02 in)

53.3 mm

(2.10 in)

53.3 mm

(2.10 in)

1/16 DIN (PM6) Dimensions

45.2 mm

(1.78 in)

45.2 mm

(1.78 in)

21.5 mm

(0.85 in)

21.6 mm

(0.85 in)

panel thickness 1.53 to 9.52 mm

(0.060 to 0.075 in)

1/16 DIN (PM6) Recommended Panel Spacing

EZ-ZONE PM Express (PID) • 6 • Install and Wire

92.00 to 92.80 mm

(3.62 to 3.65 in)

44.96 to 45.60 mm

(1.77 to 1.79 in)

panel thickness 1.53 to 9.52 mm

(0.060 to 0.375 in)

21.6 mm

(0.85 in)

Minimum

21.6 mm

(0.85 in)

Minimum

53.34 mm

(2.10 in)

100.33 mm

(3.95 in)

15.75 mm (0.62 in)

10.16 mm

(0.40 in)

54.8 mm

(2.16 in)

1.52 mm (0.06 in)

30.73 mm (1.21 in)

101.60 mm (4.00 in)

1/8 DIN (PM8) Vertical - Recommended Panel Spacing

1/8 DIN (PM8) Vertical Dimensions

EZ-ZONE PM Express (PID) • 7 • Install and Wire

53.34 mm

(2.10 in)

100.33 mm

(3.95 in)

53.8 mm

(2.16 in)

15.75 mm (0.62 in)

1.52 mm (0.06 in)

10.16 mm

(0.40 in)

30.73 mm (1.21 in)

101.60 mm (4.00 in)

44.96 to 45.6 mm

(1.77 to 1.79 in)

92.00 to 92.80 mm

(3.62 to 3.65 in)

panel thickness 1.53 to 9.52 mm

(0.060 to 0.375 in)

21.6 mm

(0.85 in)

Minimum

21.6 mm

(0.85 in)

Minimum

1/8 DIN (PM9) Horizontal Recommended Panel Spacing

1/8 DIN (PM9) Horizontal Dimensions

EZ-ZONE PM Express (PID) • 8 • Install and Wire

100.33 mm

(3.05 in)

100.33 mm

(3.95 in)

15.75 mm (0.62 in)

12.70 mm

(0.50 in)

1.52 mm (0.06 in)

30.73 mm (1.21 in)

100.84 mm (3.97 in)

92.00 to 93.0 mm

(3.62 to 3.65 in)

panel thickness 1.53 to 9.52 mm

(0.060 to 0.375 in)

21.6 mm

(0.85 in)

Minimum

21.6 mm

(0.85 in)

Minimum

92.00 to 93.0 mm

(3.62 to 3.65 in)

1/4 DIN (PM4) Horizontal Recommended Panel Spacing

1/4 DIN (PM4) Horizontal Dimensions

EZ-ZONE PM Express (PID) • 9 • Install and Wire

Installation

RETENTION COLLAR

CASE

PANEL

BEZEL

GASKET

1. Make the panel cutout using the mounting

template dimensions in this chapter. Insert the

case assembly into the panel cutout.

2. While pressing the case assembly firmly

against the panel, slide the mounting collar

over the back of the controller.

If the installation does not require a NEMA 4X seal,

slide the mounting collar up to the back of the panel

tight enough to eliminate the spacing between the

gasket and the panel.

Slide the mounting col-

lar over the back of the

controller.

Place the blade of a

screwdriver in the

notch of the mount-

ing collar assembly.

3. For a NEMA 4X seal, place the blade of a

screwdriver in the notch of the mounting collar

assembly and push toward the panel while

applying pressure to the face of the controller.

Don't be afraid to apply enough pressure to

properly install the controller.

The seal system is compressed more by mat-

ing the mounting collar tighter to the front

panel (see picture). If you can move the case

assembly back and forth in the cutout, you do

not have a proper seal. The tabs on each side

of the mounting collar have teeth that latch into

the ridges on the sides of the controller. Each

tooth is staggered at a different depth from the

front so that only one of the tabs, on each side,

is locked onto the ridges at a time.

Removing the Mounted Controller from Its Case

1. From the controller's face, pull out the tab on

each side until you hear it click.

Pull out the tab on

each side until you

hear it click.

Grab the unit above

and below the face

and pull forward.

2. Once the sides are released, grab the unit

above and below the face with two hands and

pull the unit out. If it is difficult to pull the unit

out, remove the connectors from the back of

the controller. This should make it easier to

remove.

Ó Warning:

All electrical power to the controller and con-

trolled circuits must be disconnected before

removing the controller from the front panel

or disconnecting other wiring. Failure to follow

these instructions may cause an electrical

shock and/or sparks that could cause an explo-

sion in class 1, div. 2 hazardous locations.

Returning the Controller to its Case

1. Ensure that the orientation of the controller is

correct and slide it back into the housing.

2. Using your thumbs push on either side of the

controller until both latches click.

Note:

The controller is keyed so if it feels that it will not

slide back in do not force it. Check the ori-

entation again and reinsert after correcting.

Chemical Compatibility

This product is compatible with acids, weak

alkalis, alcohols, gamma radiation and ultraviolet

radiation.

This product is not compatible with strong

alkalis, organic solvents, fuels, aromatic hydro-

carbons, chlorinated hydrocarbons, esters and

keytones.

EZ-ZONE PM Express (PID) • 10 • Install and Wire

Terminal Definitions

Slot C Terminal Function Model

power input: ac or dc+

power input: ac or dc-

PM _C_ _ _ - AAAAB _ _

Standard Bus EIA-485 common

Standard Bus EIA-485 T-/R-

Standard Bus EIA-485 T+/R+

PM _C_ _ _ - AAAAB _ _

Slot A

Input 1

(RTD) or current +,

(RTD), thermocouple -, current - or volts

-, thermistor

S1 (RTD), thermocouple + or volts +,

thermistor

Universal Sensor

input 1: all configurations

Outputs Terminal Function Configuration

1 2

common (Any switched dc output can

use.)

dc- (open collector)

dc+

Switched dc/open collector, output 1:

PM _C_ (C) _-_ AAAB _ _

dc-

dc+

Switched dc, output 2:

PM _ C _ _ (C) - _ AAAB _ _

voltage or current -

voltage +

current +

Universal Process, output 1:

PM _ C _ (F) _ - _ AAAB _ _

normally open

common

normally closed

Mechanical Relay 5 A, Form C, output 1:

PM _C_ (E) _-_ AAAB _ _

normally open

common

NO-ARC 15 A, Form A, output 2:

PM (4, 6, 8, 9) C _ _ (H) - _ AAAB _ _

normally open

common

Mechanical Relay 5 A, Form A, output 2:

PM _C_ _ (J) -_ AAAB _ _

normally open

common

Solid-State Relay 0.5 A, Form A

output 1: PM _C_ (K) _ - _ AAAB _ _

output 2: PM _C_ _ (K) - _ AAAB _ _

EZ-ZONE PM Express (PID) • 11 • Install and Wire

Note:

In the graphics below notice that the Slot A connector does not show labeling for the outputs. Labeling for

Slot A outputs is based on the controller part number.

T1 S1 R1Output 1 Output 2

CF CD CE

98 99

PM3

Output 2

Output 1

PM6

PM4

Output 2

Output 1

Output 3

Output 4

Input 2

Digital I/O 7 - 12

Communications Card

Output 2

Output 1

PM9

PM8

Output 2

Output 1

Output 3

Output 4

Input 2

Digital I/O 7 - 12

EZ-ZONE PM Express (PID) • 12 • Install and Wire

Warning:

Use National Electric (NEC) or other country-specific

standard wiring and safety practices when wiring and

connecting this controller to a power source and to

electrical sensors or peripheral devices. Failure to do

so may result in damage to equipment and property,

and/or injury or loss of life.

Note:

Maximum wire size termination and torque rating:

• 0.0507 to 3.30 mm

(30 to 12 AWG) single-

wire termination or two 1.31 mm

(16 AWG)

• 0.8 Nm (7.0 lb.-in.) torque

Note:

Adjacent terminals may be labeled differently, de-

pending on the model number.

Note:

To prevent damage to the controller, do not connect

wires to unused terminals.

Note:

Maintain electrical isolation between analog input 1

and switched dc/open collector outputs.

Power

power

Slot C

• 47 to 63 Hz

• 10VA maximum power consumption (PM3 and PM6)

• 14VA maximum power consumption (PM4, 8 and 9

Low Power

• 12 to 40VÎ (dc)

• 20 to 28VÅ (ac) Semi Sig F47

High Power

•85to264VÅ(ac)

•100to240VÅ(ac)SemiSigF47

EZ-ZONE PM Express (PID) • 13 • Install and Wire

Note:

In the drawings below for each input notice that the Slot A connector labeling is identified.

Note:

When using a 2 wire RTD, jumper S1 and T1 together

Inputs

All inputs shown below represent input 1 (the only input) and are to be connected to slot A of the PID Control.

Process Volts and Amperes

• 4 to 20 mA @ 100 Ω input impedance

• 0 to 10VÎ (dc) @ 20 kΩ input impedance

• Scalable

Resistance Temperature Detector (RTD)

• Platinum, 100 Ω @ 0°C

• Calibration to DIN curve (0.00385 Ω/Ω/°C)

• 20 Ω total lead resistance

• RTD excitation current of 0.09 mA typical. Each

ohm of lead resistance may affect the reading by

0.03°C.

• For 3-wire RTDs, the S1 lead must be connected

to R1.

• For best accuracy use a 3-wire RTD to compen-

sate for lead-length resistance. All three lead

wires must have the same resistance.

Thermocouple

• 2 KΩ maximum source resistance

• >20 MΩ input impedance

• 3 microampere open-sensor detection

• Thermocouples are polarity sensitive. The nega-

tive lead must be connected to S1.

• To reduce errors, the extension wire for thermo-

couples must be of the same alloy as the thermo-

couple.

Thermistor

• >20 MΩ input impedance

• 3 microampere open-sensor detection

Thermocouple

RTD

2 or 3 Wire

Process

Volts

Process

Amperes

Thermistor

EZ-ZONE PM Express (PID) • 14 • Install and Wire

negative

volts +

current +

Universal Process

PM _ C _ (F) _ - A A A A B _ _

normally open

common

normally closed

Mechanical Relay

Form C

PM _ C _ (E) _ - A A A A B _ _

Solid-State Relay

Form A

L1 and/or L2

K1 and/or K2

PM _ C _ (K) (K) - A A A A B _ _

W1 and/or W2

dc +

dc -

Y1 and/or Y2

common

Switched DC

PM _ C _ (C) (C) - A A A A B _ _

NO-ARC Relay Form A

PM _ C _ _ (H) - A A A A B _ _

Open Collector

Load

Power

Supply

dc -

common

PM _ C _ (C) _ - A A A A B _ _

Power Supply Note:

Switched dc and Process outputs use a common power supply with a maximum current output of 40mA. As an

example, supplied current (mA) from output 1 and 2 can be 20/20, 30/10, 30/0, 10/30, etc...

Outputs

Please note all outputs are connected exclusively to slot A. Output availability is based on the part number of

your PID Control.

EZ-ZONE PM Express (PID) • 15 • Install and Wire

Switched DC

• Supplied current up to a maximum of 30 mA. See

Power Supply note above.

• Short circuit limited to <50 mA

• 22 to 32VÎ (dc) open circuit voltage

• Use dc- and dc+ to drive external solid-state relay.

• DIN-A-MITE compatible

- single-pole: up to 4 in parallel or 4 in series

- 2-pole: up to 2 in parallel or 2 in series

- 3-pole: up to 2 in series

Open Collector

• 100 mA maximum output current sink

• 30VÎ (dc) maximum supply voltage

• Any switched dc output can use the common

terminal.

• Use an external power supply to control a dc load,

with the load positive to the positive of the power

supply, the load negative to the open collector and

common to the power supply negative.

See Quencharc note.

Mechanical Relay Form C

• 5 A at 240VÅ (ac) or 30VÎ (dc) maximum resis-

tive load

• 20 mA at 24V minimum load

• 125 VA pilot duty at 120/240VÅ (ac), 25 VA at

24VÅ (ac)

• 100,000 cycles at rated load

• Output does not supply power.

• For use with ac or dc

See Quencharc note.

Mechanical Relay Form A

• 5 A at 240VÅ (ac) or 30VÎ (dc) maximum resis-

tive load

• 20 mV at 24V minimum load

• 125 VA pilot duty @ 120/240VÅ (ac), 25 VA at

24VÅ (ac)

• 100,000 cycles at rated load

• Output does not supply power.

• For use with ac or dc

See Quencharc note.

NO-ARC Relay Form A

• 15 A at 85 to 264VÅ (ac) resistive load only

• 1/16 DIN models only

• 2,000,000 cycle rating for NO-ARC circuit

• 100 mA minimum load

• 2 mA maximum off state leakage

• Do not use on dc loads.

• Output does not supply power.

Solid-State Relay Form A

• 0.5 A at 20 to 264VÅ (ac) maximum resistive

load

• 20 VA 120/240VÅ (ac) pilot duty

• Opto-isolated, without contact suppression

• Maximum off state leakage of 105 microamperes

• Output does not supply power

• Do not use on dc loads.

• See Quencharc note.

Universal Process

• 4 to 20 mA into 800 Ω maximum load

• 0 to 10VÎ (dc) into voltage 1 kΩ minimum load

• Scalable

• Output supplies power (See Power Supply note

previous page).

• Cannot use voltage and current outputs at same

time

Quencharc Note:

Switching pilot duty inductive loads (relay coils, solenoids, etc.) with

the mechanical relay, solid state relay or open collector output op-

tions requires use of an R.C. suppressor.

Mechanical Relay Form A

PM _ C _ _ (J) - A A A A B _ _

EZ-ZONE PM Express (PID) • 16 • Keys and Displays

Zone Display:

When [2onE] (found in the

Factory Page) is set to on, indi-

cates the controller zone.

[1] to [9] = zones 1 to 9

[A] = zone 10 [E] = zone 14

[b] = zone 11 [F] = zone 15

[C] = zone 12 [h] = zone 16

[d] = zone 13

Lower Display:

Indicates the set point or output

power value during operation,

or the parameter whose value

appears in the upper display.

A/M Key:

This key will toggle the control

mode between the current value of

the C.M prompt (Off, MAn, AUto)

and Manual when the A/M button

is pushed and held for 3 seconds.

Infinity Key: ˆ

Clears and Silences alarms, press

to back up one level, or press and

hold for two seconds to return to

the Operations Menu.

Temperature Units Indicator

Lights:

Indicates whether the tempera-

ture is displayed in Fahrenheit

or Celsius.

Output Activity:

Number lights indicate activity of

outputs 1 and 2.

Percent Units Indicator:

Lights when the controller is

displaying values as a percentage

or when the open-loop set point

is displayed.

Communications Activity:

Flashes when another device

is communicating with this

controller.

Up and Down Keys: ¿ ¯

In the Operations Menu, adjusts the

set point in the lower display. In other

pages, changes the upper display to

a higher or lower value, or changes a

parameter selection.

Keys & Displays 16

DIN PID Controller

Advance Key:

‰

Advances through

parameter

prompts.

Left Display:

In the Operations Menu, displays

the process value, otherwise dis-

plays the value of the parameter

in the left display.

With a few exceptions, all of the key functions described for the 16

DIN PID Controller apply to the 32

DIN PID Controller as well.

Right Display:

Indicates the set point or output

power value during operation,

or the parameter whose value

appears in the right display.

DIN PID Controller

PM3

PM6

Upper Display:

In the Operations Menu,

displays the process

value, otherwise displays

the value of the parameter

in the lower display.

Note:

As shown in the graphics on the following page the PM4, 8 and 9 controls will include two "EZ" buttons (EZ1

and EZ2). The button identified as EZ1 is equivalent to the EZ button described above where the button identi-

fied as EZ2 has no functionality. Assuming the issue that caused the limit to trip has been rectified pushing

the EZ1 will reset the limit as described for the Reset button above. All other buttons found on these controls,

maintain the same functionality as described above for the 16

DIN.

EZ-ZONE PM Express (PID) • 17 • Keys and Displays

Responding to a Displayed Message

Keys & Displays for 1/8

or 1/4 DIN PID Controllers

PM8

PM9

PM4

An active message will cause the display to toggle

between the normal settings and the active mes-

sage in the upper or left display and [Attn] in the

lower or right display. Your response will depend

on the message and the controller settings. Some

messages, such as Tuning, indicate that a process

is underway. If a message is generated in the

right or lower display that can be cleared (such

as [AL;h1]), simply push the infinity ˆ key to

execute the action ([CLr]).

[AL;L1] Alarm Low 1 (sensor input below low

alarm set point)

[AL;h1] Alarm High 1 (sensor input above high

alarm set point)

[AL;E1] Alarm Error 1 (alarm state cannot be

determined due to lack of sensor input)

[Er;i1] Error Input 1 (sensor is not providing a

valid signal to the control)

[tUn1] Tuning (controller is autotuning the

control loop)

[`rP1] Ramping (controller is ramping to a

new set point)

EZ-ZONE PM Express (PID) • 18 • Operations Menu

‰

[````] PAr1

[````] PAr2

[`AUt] Autotune

[`C;M] Control Mode

[`h;pb] Heat Proportional Band

[`C;pb] Cool Proportional Band

[``ti] Time Integral

[``td] Time Derivative

[o;tb1] Time Base

[o;tb2] Time Base

[`A;lo] Alarm Low Set Point

[`A;hi] Alarm High Set Point

[`i;Ca] Calibratin Offset

Operations Menu

Upon power up of the control, using

the advance key will scroll through the

various prompts found in the Operations

Menu. At any point within the Operations

menu to return to the default display

push the Inﬁnity ˆ key.

Operations Menu

Display Parameter Name Description

[`AUt]

[ AUt]

Autotune

Start an autotune. While active the upper

or left and lower or right display will flash

[tUn1] and [Attn].

Appears if: Heat or cool algorithm set to PID

[`C;M]

[ C.M]

Control Mode Active

View the current control mode.

Appears if: Always

[`h;Pb]

[ h.Pb]

Heat Proportional Band

Set the PID proportional band for the heat

outputs.

Appears if: Heat algorithm set to PID

[`C;Pb]

[ C.Pb]

Cool Proportional Band

Set the PID proportional band for the cool

outputs.

Appears if: Cool algorithm set to PID

[``ti]

[ ti]

Time Integral

Set the PID integral for the outputs.

Appears if: Heat or cool algorithm set to PID

[``td]

[ td]

Time Derivative

Set the PID derivative time for the outputs.

Appears if: Heat or cool algorithm set to PID

[o;tb1]

[o.tb1]

Time Base Output 1

Set the time base for fixed-time-base

control.

Appears if: Output 1 set to heat or cool with

control algorithm set to PID.

[o;tb2]

[o.tb2]

Time Base Output 2

Set the time base for fixed-time-base

control.

Appears if: Output 2 set to heat or cool with

control algorithm set to PID.

[`A;Lo]

[ A.Lo]

Alarm Low Set Point

Process - set the process value that will trig-

ger a low alarm.

Deviation - set the span of units (using nega-

tive numbers) from the closed loop set

point that will trigger a low alarm.

Appears if: If Alarm Type [`A;ty] is set to

Process or Deviation Alarm

Range (Defaults are shown bold)

[``no] No

[`yES] Yes

[`off] Off

[AUto] Auto

[MAn] Manual

0 to 9,999.000°F or units

0 to 5,555.000°C

Units, 25.0°F or 14.0°C

0 to 9,999.000°F or units

0 to 5,555.000°C

Units, 25.0°F or 14.0°C

0 to 9,999 seconds per repeat

180

0 to 9,999 seconds

0 seconds

0.1 to 60.0 seconds (solid-state relay or switched dc)

5.0 to 60.0 seconds (mechanical relay & NO-ARC power control)

1 sec. [SSR & sw dc], 20.0 sec. [mech. relay & NO-ARC]

0.1 to 60.0 seconds (solid-state relay or switched dc)

5.0 to 60.0 seconds (mechanical relay & NO-ARC power control)

1 sec. [SSR & sw dc], 20.0 sec. [mech. relay & NO-ARC]

-1,999.000 to 9,999.000°F or units

-1,128.000 to 5,537.000°C

Units, 32.0°F or 0.0°C

EZ-ZONE PM Express (PID) • 19 • Operations Menu

Range (Defaults are shown bold)

[``no] No

[`yES] Yes

[`off] Off

[AUto] Auto

[MAn] Manual

0 to 9,999.000°F or units

0 to 5,555.000°C

Units, 25.0°F or 14.0°C

0 to 9,999.000°F or units

0 to 5,555.000°C

Units, 25.0°F or 14.0°C

0 to 9,999 seconds per repeat

180

0 to 9,999 seconds

0 seconds

0.1 to 60.0 seconds (solid-state relay or switched dc)

5.0 to 60.0 seconds (mechanical relay & NO-ARC power control)

1 sec. [SSR & sw dc], 20.0 sec. [mech. relay & NO-ARC]

0.1 to 60.0 seconds (solid-state relay or switched dc)

5.0 to 60.0 seconds (mechanical relay & NO-ARC power control)

1 sec. [SSR & sw dc], 20.0 sec. [mech. relay & NO-ARC]

-1,999.000 to 9,999.000°F or units

-1,128.000 to 5,537.000°C

Units, 32.0°F or 0.0°C

EZ-ZONE PM Express (PID) • 20 • Operations Menu

Operations Menu (cont.)

Display Parameter Name Description

[`A;hi]

[ A.hi]

Alarm High Set Point

Process - set the process value that will trig-

ger a high alarm.

Deviation - set the span of units from the

closed loop set point that will trigger a

high alarm.

Appears if: If Alarm Type (A.ty) is set to

Process or Deviation Alarm

[`i;CA]

[ i.CA]

Calibration Offset

Set an offset value for a process output.

Appears if: Always

‰

[````] PAr1

[````] PAr2

[`AUt] Autotune

[`C;M] Control Mode

[`h;pb] Heat Proportional Band

[`C;pb] Cool Proportional Band

[``ti] Time Integral

[``td] Time Derivative

[o;tb1] Time Base

[o;tb2] Time Base

[`A;lo] Alarm Low Set Point

[`A;hi] Alarm High Set Point

[`i;Ca] Calibratin Offset

Operations Menu

Upon power up of the control, using

the advance key will scroll through the

various prompts found in the Operations

Menu. At any point within the Operations

menu to return to the default display

push the Inﬁnity ˆ key.

Page is loading ...

Watlow Electric EZ-ZONE PM User guide

Brand: Watlow Electric

Model: EZ-ZONE PM

Category: Recording Equipment

Type: User guide

This manual is also suitable for

EZ-ZONE PM Express

Download PDF

report

Watlow Electric EZ-ZONE PM User guide

This manual is also suitable for

Watlow Electric EZ-ZONE PM User guide

Related papers

Other documents