Samsung DIGIMAX 230 User manual

SAMSUNG TECHWIN CO., LTD.

OPTICS & DIGITAL IMAGING DIVISION

145-3, SANGDAEWON 1-DONG, JUNGWON-

GU,SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121

TEL : (82) 31-740-8086,8088, 8090, 8092, 8099

FAX : (82) 31-740-8398, 8399

SAMSUNG OPTO-ELECTRONICS AMERICA, INC.

HEADQUARTERS

40 SEAVIEW DRIVE, SECAUCUS, NJ07094

TEL : (1) 201-902-0347

FAX : (1) 201-902-9342

WESTERN REGIONAL OFFICE

18600 BROADWICK ST.,

RANCHO DOMINGUEZ, CA 90220

TEL : (1) 310-537-7000

FAX : (1) 310-537-1566

SAMSUNG OPTO-ELECTRONICS UK LTD.

SAMSUNG HOUSE, 3 RIVERBANK WAY,

GREAT WEST ROAD, BRENTFORD,

MIDDLESEX,TW8 9RE, U.K.

TEL : (44) 20-8232-3280

FAX : (44) 20-8569-8385

SAMSUNG OPTO-ELECTRONICS GMBH

SAMSUNG HAUS

AM KRONBERGER HANG 6, 65824 SCHWALBACH,

GERMANY

TEL : (49) 6196-66 53 03

FAX : (49) 6196-66 53 66

SAMSUNG FRANCE S.A.R.L.

BP 51 TOUR MAINE MONTPARNASSE 33,

AV .DU MAINE 75755,

PARIS CEDEX 15, FRANCE

TEL : (33) 1-4279-2282/5

FAX : (33) 1-4320-4510

SAMSUNG TECHWIN MOSCOW OFFICE

KOSMODAMIANSKAYA NABEREZNA 40/42,

MOSCOW, 113035, RUSSIA

TEL : (7) 095-937-7950

FAX : (7) 095-937-4851

TIANJIN SAMSUNG OPTO-ELECTRONICS CO.,LTD.

7 PINGCHANG ROAD NANKAI DIST., TIANJIN

P.R CHINA

POST CODE:300190

TEL : (86) 22-2761-8867

FAX : (86) 22-2761-8864

Internet address - http : //www.samsungcamera.com/

The CE Mark is a Directive conformity mark of the

European Community (EC)

Thank you for buying a Samsung Camera. This manual will guide you through using the Digimax 230, including taking

images, downloading images and using MGI PhotoSuite III SE software.

Please read this manual before using your new camera.

ENGLISH

SPECIAL FEATURES

Thank you for buying a Samsung Digital Camera.

This digital camera has the following features.

A high resolution of 2.0 mega pixels

A 3 X optical and 2 X digital zoom lens

Movie clip recording function

Voice Recording & Playback for still image

An easy and fast PC interface with USB Storage Driver & Digimax viewer

This device has been tested in accordance with the limits of a class B digital device

under item 15 of the FCC rules. These limits are designed to provide protection against

harmful interference in commercial installation.

This equipment generates, absorbs and can emit radio frequency energy. If it is not

installed and used in accordance with the instructions, it may cause harmful interference

to radio communication.

There is however, no guarantee that interference will not occur in some situations.

Should any interference occur when this device is in operation, please try one or more of

the following measures.

Change the location and direction of any aerial.

Increase distance between camera and affected device.

Use a different socket away from the affected device.

Please contact a Samsung agent or a radio/TV engineer.

This device complies with part 15 of the FCC Rules.

An FCC warning

MANUFACTURER’S CONTENTS

Manufacturer's contents

Please check that you have the correct contents before using this product.

READY

AC Adapter

Digital camera

CompactFlash

TM

card (CF CARD)

4 AA Alkaline Batteries Pouch

User manual

Accessories (optional)

Product warranty

Applications S/ W ,

Driver CD-ROM

USB cableVideo cable Camera strap

THIS DIGITAL CAMERA CAN BE USED FOR

Editing images

on a PC

Recording images

onto CD

Printing images

Viewing images

on TV

READY

THIS DIGITAL CAMERA CAN BE USED FOR

Inserting images

directly into any

electronic document

Taking a self-portrait

and using the image

to personalize name

cards

You can even create your

own unique gift-wrap paper

by using your digital

images.

Creation of

a digital photo album

CONTENTS

Ready

Getting to Know your camera 7

Safety note 8

Identification of features 10

Product Exterior 10

Viewfinder 12

LCD panel indicator 14

LCD monitor indicator 15

LCD monitor menu indicator 17

Preparation 19

Connecting to Power 19

Using the batteries 19

Using the AC power adapter 20

Attaching the strap 20

Inserting the CF CARD 21

Removing the CF CARD 21

Instructions on how to use the CF CARD 23

Selecting the date and time 24

Advanced

Setting up play function

by using the camera button 54

Setting up play back function using the LCD

monitor 59

Setting up the camera system 65

Starting Set up mode 65

Connecting to an external monitor 74

PC mode 75

Important notes 76

Caution 76

Warning indicator 78

Before contacting a service center 79

Specification 82

Camera working mode 26

Taking photos 27

Setting up the shooting function 30

Movie clip shot 30

Using the camera buttons

to adjust the camera 31

Using the LCD monitor

to adjust the camera 38

Setting up play back functions 53

Starting play mode 53

Software

Software manual 84

How to set up the software for Windows 85

Setting up USB driver for Windows 86

Setting up DirectX 8.1 for windows 88

Setting up Digimax Viewer 90

Setting up the MGI PhotoSuite III SE 92

Connecting the camera for Windows 95

Removable Disk 95

How to use the software 97

Digimax Viewer 97

MGI PhotoSuite III SE 98

Removing USB Driver for Windows 111

Connecting the camera for MAC 113

How to install and

use the USB driver for MAC 114

FAQ 115

GETTING TO KNOW YOUR CAMERA

Symbol Explanations

Prior to using this camera, please read the user manual thoroughly.

Keep the manual in a safe place.

This manual contains instructions on using this camera that will help you to use this camera

safely and correctly. This will help prevent danger and injury to others.

READY

Warning

This is a descriptive statement warning of the result if the instructions are ignored or not

understood.

Note

This explains use of the camera, please refer to this.

Reference

This should further assist camera operation.

SAFETY NOTE

WARNING

Do not attempt to modify this camera in any way. This may result in fire, injury, electric

shock or severe damage to you or your camera. Internal inspection, maintenance and

repairs should be carried out by your dealer or Samsung Camera Service Center.

Do not use the flash in close proximity to the people or animals. Positioning the flash too

close to your subject’s eyes, may cause eyesight damage. Do not attempt to photograph

children using a flash closer than 1 meter proximity.

When taking photographs, never point the lens of the camera directly into very strong

light. This may result in permanent damage to the camera or your eyesight.

Please do not use this product in close proximity to flammable or explosive gases, as this

could increase the risk of explosion.

For safety reasons keep this product and accessories out of reach of children or animals

to prevent accidents e.g.:

Swallowing batteries or small camera accessories.

In case of accidents, please consult a doctor immediately.

There is a risk of permanent eye damage if the flash is operated at a distance of less

than one meter from a person’s eyes.

There is a possibility of injury from the camera’s moving parts.

Should any form of liquid enter the camera, do not use it. Switch off the camera, and then

disconnect the power source (batteries or AC Power Adapter). You must contact your

dealer or Samsung Camera Service Center. Do not continue to use the camera as this

may cause a fire or electric shock.

Do not insert or drop metallic or inflammable foreign objects into the camera through

access points e.g. CARD slot and battery chamber. This may cause a fire or electric

shock.

Do not operate this camera with wet hands. This could pose a risk of electric shock.

READY

SAFETY NOTE

NOTE

Do not leave this camera in places subject to extremely high temperatures, such as a

sealed vehicle, direct sunlight or other places of extreme variances in temperature.

Exposure to extreme temperatures may adversely affect the camera’s internal

components and could cause a fire.

When in use, do not cover the camera or AC Power Adapter. This may cause heat to build

up and distort the camera case or cause a fire.

Always use the camera and its accessories in a well-ventilated area.

Leakage, overheating, or burst batteries could result in fire or injury.

Do not short circuit, heat or dispose of batteries in fire.

Do not use old batteries with new ones, or mix brands of batteries.

Ensure the batteries are positioned correctly with regard to polarity (+ / -).

When the camera is not in use for long periods, always unplug the camera from its power

source (batteries or AC Power Adapter) for safety purposes.

Leaking batteries can cause fire and pollution to the environment.

Allowing dust to accumulate in the camera over a long period is hazardous as extreme

circumstances may cause a fire. It is best to clean your camera prior to seasonal periods

of high humidity.

Consult your dealer or Samsung Camera Service Center for information on the cost of

cleaning your camera.

Do not move the camera while it is switched on, if you are using the AC Power Adapter.

After use, always switch off the camera before unplugging the adapter from the AC Power

wall socket. Then make sure that any connector cords or cables to other devices are

disconnected before moving the camera.

Failure to do so may damage the cords or cables and cause a fire or electric shock.

IDENTIFICATION OF FEATURES

Product Exterior (Front / Top / Bottom)

Microphone

Shutter button

(page 31)

Mode dial (page 26)

Strap eyelet

Lens

Self-timer lamp

Viewfinder

Flash fading control

sensor

LCD panel

Flash

Tripod socket

Cover lock

Battery

chamber cover

Mode dial lamp

READY

IDENTIFICATION OF FEATURES

Product Exterior (Back)

LCD monitor

Autofocus

indicator (Green)

lamp

Viewfinder

Flash indicator

(Red) lamp

5-function button

Speaker

Zoom ( W ) / Thumbnail

button

(page 33 / page 54)

Zoom (T) /Digital zoom

button

(page 33 / page 55)

Power button (page 31)

LCD button

MENU button

LANDSCAPE /

DELETE button

FLASH/LEFT button (page 35)

PLAY&PAUSE/DOWN button (page 57 / page 34)

OK button (page 34 / page 55 )

SELF-TIMER / RIGHT button (page 37)

MIC / UP button (page 57 / page 34)

/

II

IDENTIFICATION OF FEATURES

Product Exterior (side)

Viewfinder

Close range picture area mark

Picture area frame

Optimum picture area over 1.5m

Autofocus frame

Optimum picture area within 0.8m ~ 1.5m

Video connection terminal

DC input connection point (DC 6V IN)

USB connection terminal

Card cover

CF CARD

Card eject lever

READY

IDENTIFICATION OF FEATURES

Reference

Vertical and Horizontal shots are taken in the same way.

Avoid obstructing the lens or the flash when you take a picture.

Note

As there can be some differences between what is seen through the Viewfinder and the

resulting image when taken at a range closer than 1.5m, it is recommended that you use the

LCD monitor to compose the shot.

[ Horizontal grip ] [ Vertical grip ]

IDENTIFICATION OF FEATURES

LCD panel indicator

The LCD panel displays information about the shooting conditions.

Image size

L : 1600X1200

M : 0800X0600

S : 640X0480

Shooting information

MACRO SHOT mode : Number of available shots remaining

STILL IMAGE mode : Number of available shots remaining

MOVIE CLIP mode : Available recording time

PLAY mode : Number of available shots remaining

SETUP mode : Number of available shots remaining

PC mode : USB

Battery condition indicator

: The batteries are fully charged

: Prepare new batteries

: There is no battery capacity

Replace new batteries

Flash

Auto flash and Red eye reduction :

Slow synchro : No indicator

Auto flash :

Fill in flash :

Flash off :

READY

IDENTIFICATION OF FEATURES

LCD monitor indicator

The LCD monitor displays information about the shooting conditions.

SHOT mode

Whenever you press the LCD button, the LCD monitor will change in the following order :

Image & Status Image only LCD Off.

1 Battery condition page 14

2 Flash page 36

3 Self-timer page 37

4 Landscape shot page 32

5Macro shot page 26

6 White balance page 44

7 Metering methods page 48

8 Exposure compensation page 46

Image & Status

-2.0 ~ 0 ~ +2.0

IDENTIFICATION OF FEATURES

9ISO page 49

10 Focusing Methods page 39

11 Sharpness page 50

12 Image quality page 43

13 Image size page 42

14

Number of available shots remaining

15 Zoom / Digital zoom page 33

16 Movie clip shot page 30

17 Shooting mode page 40

PLAY mode

13/13

15SEC

2002/ 1/ 1/ 00 : 00

REC

2x

Movie clip shot

Movie clip running time

Image magnification

Date / Time

Image & Status

When an image that has sound

information is selected, this indicator

will be displayed.

AUTO 200 400

9

This indicator will display when you set

DPOF.

DPOF (page 61)

Battery condition (page 14)

The last stored image number is

displayed.

Number of stored images

Sound indicator

When you press the MIC ( )

button, this indicator will blink and

sound recording starts.

Sound recording

READY

IDENTIFICATION OF FEATURES

LCD monitor menu indicator

Each mode has a menu as shown below. The default settings in each mode are printed below.

FOCUSING : select focusing methods (page 39)

SHOOTING MODE : select shooting mode (page 40)

IMAGE SIZE : select image size (page 42)

QUALITY : select image quality (page 43)

WHITE BALANCE : select white balance (page 44)

STILL IMAGE / MACRO SHOT mode

REC.TIME : select recording time (page 52)

VOICE : set the voice recording function ON/OFF

MOVIE CLIP mode

EXPOSURE : select exposure value(page 46)

Select metering methods(page 48)

ISO : select ISO sensitivity (page 49)

SHARPNESS : select image sharpness(page 50)

LCD : select LCD brightness (page 51)

CENTRAL

SINGLE

1600X1200

FINE

AUTO

FOCUSING

P1 SELECT OK SET

EV 0.00

METERING FULL

AUTO

NORMAL

BRIGHTNESS 5

EXPOSURE

P2 SELECT OK SET

REC. TIME 15SEC

REC. TIME

SELECT OK SET

Main Menu

Sub Menu

IDENTIFICATION OF FEATURES

Reference

There is no associated menu in PC mode and the LCD monitor is always turned off in PC

mode.

FORMAT : format CF CARD (page 65)

POWER OFF : select auto power off time (page 66)

DATE/TIME : select date/time (page 67)

BEEP : set the beep sound ON/OFF (page 68)

VIDEO OUT : select video out signal (page 69)

SETUP mode

DELETE ALL : delete all stored images (page 59)

SLIDE SHOW : select slide show function (page 60)

DPOF : select DPOF function (page 61)

FOLDER : change the folder name to 100SSCAM

(page 64)

LCD : select LCD brightness (page 64)

PLAY mode

LANGUAGE : select OSD(On Screen Display)

language (page 70)

RESET : select the default camera setting (page 71)

NO

START

QUANTITY

100SSCAM

BRIGHTNESS 5

DELETE ALL

SELECT OK SET

FORMAT NO

3 MIN

02/ 1/ 1

ON

NTSC

FORMAT

P1 SELECT OK SET

ENGLISH

NO

FORMAT

P2 SELECT OK SET

READY

PREPARATION

Connecting to Power

There are two ways in which to provide the camera with power. You can use batteries (AA

Alkaline, Ni-MH), or alternatively, you can use an AC Adapter (DC 6V / 2.0A).

Using the batteries

1

Pull the battery chamber cover lock in the direction of the

arrow( ) and open the battery chamber cover by pushing

in the direction of the arrow( ).

2

Insert the batteries taking note of the polarity (+ /

-

).

3

To close the battery chamber cover, push it until it clicks.

Reference

This camera will automatically switch off when not in use for a period of time.

We recommend high–capacity ALKALINE batteries (2000mAh) as manganese batteries

cannot deliver sufficient power.

Note

Important information about battery usage

Please remove the batteries if the camera will not be used for long periods.

Batteries can lose power over time and are prone to leaking if kept inside the camera.

Low temperatures (below O°C) can affect the performance of the batteries and you may

experience reduced battery life.

Batteries will normally recover at normal temperatures.

Do not use old and new batteries at the same time.

During extended use of the camera, the camera body may become warm. This is perfectly

normal. If you are planning to use this camera for long periods of time, it is advisable to

use an AC adapter.

Page is loading ...

Samsung DIGIMAX 230 User manual

This manual is also suitable for

Samsung DIGIMAX 230 User manual

Related papers

Other documents