Porter Cable 90538674 User manual

Brand: Porter Cable

Model: 90538674

Category: Power tools

Type: User manual

This manual is also suitable for

PC600D

3/8 inch (10mm) Drill

www.portercable.com

INSTRUCTIVO DE OPERACIÓN,

CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA.

ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL

PRODUCTO.

CATALOG NUMBER

PC600D

Instruction manual

Manuel d'instructions

Manual de instrucciones

90538674 PC600D Drill 10/1/08 9:24 AM Page 1

General Safety Rules

Read all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious injury. The term “power

tool” in all of the warnings listed below refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust.

Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions

can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating

a power tool. Do not use a power tool while you are tired or under the

influence of drugs, alcohol or medication.

A moment of inattention while

operating power tool may result in serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position before

plugging in.

Carrying power tools with your finger on the switch or plugging in

power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,

clothing and gloves away from moving parts.

Loose clothes, jewelry or long hair

can be caught in moving parts. Air vents often cover moving parts and should also

be avoided.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of these devices

can reduce dust-related hazards.

90538674 PC600D Drill 10/1/08 9:24 AM Page 2

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool,

taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a

hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

• Wear ear protectors with impact drills.

Exposure to noise can cause hearing loss

• Use auxiliary handles supplied with the tool.

Loss of control can cause personal

injury.

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord.

Contact with a

"live" wire will make exposed metal parts of the tool "live" and shock the operator.

• Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

• Keep your hair, clothing, and gloves away from air vents. Air vents often cover

moving parts in which these items can be caught.

• Keep handles dry, clean, free from oil and grease.

It is recommended to use rubber

gloves. This will enable better control of the tool.

ALWAYS

use safety glasses. Everyday eyeglasses are NOT safety

glasses. Also use face or dust mask if drilling operation is dusty. ALWAYS WEAR

CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CPA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the state of California to cause

cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work

with approved safety equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

90538674 PC600D Drill 10/1/08 9:24 AM Page 3

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury.

Always use NOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles away

from face and body.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

Symbols

• The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current

o ................no load speed

................Class I Construction ..................earthing terminal

(grounded) ................safety alert symbol

................Class II Construction .../min or rpm ........revolutions or reciprocation

(double insulated) per minute

• When using an extension cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop in line voltage resulting in

loss of power and overheating. The following table shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt, use the next heavier

gage. The smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gage

Than Than

0-6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

90538674 PC600D Drill 10/1/08 9:24 AM Page 4

FUNCTIONAL DESCRIPTION

Figure A

1. Variable speed switch

2. Lock-on button

3. Reversing lever

4. Keyless chuck

5. Belt clip

90538674 PC600D Drill 10/1/08 9:24 AM Page 5

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

Drill may stall (if overloaded or improperly used) causing a twist. Always

expect the stall. Grip the drill firmly with both hands to control the twisting action and

prevent loss of control which could cause personal injury. If a stall does occur, release

the trigger immediately and determine the reason for the stall before re-starting.

ASSEMBLY

To reduce the risk of injury, before assembly, make sure that the tool is

switched off and unplugged.

INSERTING A DRILL BIT OR OTHER ACCESSORY (FIGURE B)

Do not attempt to tighten drill bits (or any other accessory) by

gripping the front part of the chuck and turning the tool on.

Damage to the chuck

and personal injury may occur when changing accessories.

Always ensure the bit is secure before starting the tool.

A loose bit

may eject from tool causing possible personal injury.

Your tool features a keyless chuck (4) for greater convenience. To insert a drill bit or

other accessory, follow the steps listed below.

• Grasp the rear half of the chuck with one hand and use your other hand to rotate the

front half counterclockwise, as shown in figure B. Rotate far enough so that the chuck

opens sufficiently to accept the desired accessory.

• Insert the bit or other accessory about 3/4 inch (19 mm) into the chuck and tighten

securely by holding the rear half of the chuck and rotating the front portion in the

clockwise direction.

• To release the accessory, repeat step 1 listed above.

REMOVING AND ATTACHING THE CHUCK (FIGURE C)

• Open the chuck as far as possible.

• Remove the chuck retaining screw, located in the chuck, by turning it clockwise using a

screwdriver (lefthand thread).

• Tighten an Allen key of 1/4 inch or greater size (not supplied) into the chuck and strike it

with a soft hammer in a counterclockwise direction as shown.

• Remove the Allen key.

• Remove the chuck by turning it counterclockwise.

• To attach the chuck, screw it onto the spindle and secure it with the chuck retaining

screw.

OPERATING INSTRUCTIONS

To reduce the risk of serious personal injury,

read, understand and

follow all safety warnings and instructions prior to using tool.

It is important to support the work properly and to hold the drill

firmly with both hands to prevent loss of control which could cause personal

injury.

Do not attempt to tighten drill bits (or any other accessory) by

gripping the front part of the chuck and turning the tool on.

Damage to the chuck

and personal injury may occur when changing accessories.

To reduce the risk of injury,

always unplug drill from power supply

before making any adjustments or changing accessories.

To reduce the risk of injury,

let the tool work at its own pace. Do not

overload.

SWITCHES (FIGURE D)

• To switch the tool on, press the variable speed switch (1). The tool speed depends on

how far you press the switch.

• For continuous operation, press the lock-on button (2) and release the variable speed

switch. This option is available only at full speed.

90538674 PC600D Drill 10/1/08 9:24 AM Page 6

• To switch the tool off, release the variable speed switch. To switch the tool off when in

continuous operation, press the variable speed switch once more and release it.

The drill should only be locked ON when it is held stationary in a drill

press stand or other means; NOT BY HAND! Never unplug the tool with the locking

feature engaged. To do so will cause the tool to start immediately the next time it is

plugged in.

REVERSING LEVER

The reversing lever (3) is used for withdrawing bits from tight holes and removing

screws. It is located above the trigger switch. To reverse the motor, release the trigger

switch FIRST and then push the lever to the right. After any reversing operations,

return lever to forward position. Never change the direction of rotation while the motor is

running.

DRILLING

• Always unplug the drill when attaching or removing accessories. When attaching

accessories in the drill chuck, it is important to securely tighten the chuck using all

three holes to prevent slippage. When using a keyless chuck, hand tighten firmly.

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the safety instructions.

• Secure and maintain work area, as instructed in the safety instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep

the drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

but not so much as to stall the motor or deflect the bit.

• Hold the drill firmly with both hands to control its twisting action.

• Drills equipped with a side handle must use the side handle.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the

last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce

jamming.

DRILLING IN WOOD

Holes in wood can be made with the same twist drill bits used for metal or with spade

bits. These bits should be sharp and should be pulled out frequently when drilling to

clear chips from the flutes.

DRILLING IN METAL

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass

which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil

or lard oil.

DRILLING IN MASONRY

Use carbide tipped masonry bits. Refer to

Drilling

section. Keep even force on the drill

but not so much that you crack the brittle material. A smooth, even flow of dust indicates

the proper drilling rate.

90538674 PC600D Drill 10/1/08 9:24 AM Page 7

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Cord not plugged in. • Plug tool into a working outlet.

• Circuit fuse is blown. • Replace circuit fuse. (If the

product repeatedly causes the

circuit fuse to blow, discontinue

use immediately and have it

serviced at a Porter Cable

service center or authorized

servicer.)

• Circuit breaker is tripped. • Reset circuit breaker. (If the

product repeatedly causes the

circuit breaker to trip,

discontinue use immediately

and have it serviced at a Porter

Cable service center or

authorized servicer.)

• Cord or switch is damaged. • Have cord or switch replaced

at a Porter Cable Service

Center or Authorized Servicer

For assistance with your product, visit our website at www.portercable.com for a list of

service centers, or call the Porter-Cable Customer Care Center at (888) 848-5175.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at

www.portercable.com. You can also order parts from your nearest Porter-Cable Factory Service

Center or Porter-Cable Authorized Warranty Service Center. Or, you can call our Customer Care

Center at (888) 848-5175.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about

Porter-Cable, its factory service centers or authorized warranty service centers, visit our website at

www.portercable.com or call our Customer Care Center at (888) 848-5175. All repairs made by our

service centers are fully guaranteed against defective material and workmanship. We cannot

guarantee repairs made or attempted by others.

You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,

Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to include all of the

information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

Since accessories, other than those offered by Porter-Cable, have not

been tested with this product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only Porter-Cable recommended accessories

should be used with this product.

A complete line of accessories is available from your Porter-Cable Factory Service

Center or a Porter-Cable Authorized Warranty Service Center. Please visit our Web

Site www.portercable.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace, without charge, any defects due to faulty

materials or workmanship for three years from the date of purchase for tools (two years

for batteries). This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit

www.portercable.com or call (888) 848-5175. This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others.

This warranty gives you specific legal rights and you may have other rights which vary

in certain states or provinces.

90538674 PC600D Drill 10/1/08 9:24 AM Page 8

In addition to the warranty, PORTER-CABLE tools are covered by our:

1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn

parts caused by normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performance of your PORTER-CABLE Power Tool for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

products sold in Latin America, see country specific warranty information contained in

the packaging, call the local company or see website for warranty information.

To register your tool for warranty service visit our website at www

.portercable.com.

ARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (888) 848-5175 for a free

replacement.

The following are PORTER-CABLE trademarks for one or more power tools and accessories: a

gray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal

stripes. The following are also trademarks for one or more Porter-Cable and Delta products: 2 BY

4®, 890™, Air America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders

Saw®, Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's Saw®,

Delta®, DELTA®, Delta Industrial®, DELTA MACHINERY & DESIGN™, Delta Shopmaster and

Design®, Delta X5®, Deltacraft®, DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND

DESIGN®, EASY AIR®, EASY AIR TO GO™, ENDURADIAMOND®, Ex-Cell®, Front Bevel

Lock®, Get Yours While the Sun Shines®, Grip to Fit®, GRIPVAC™, GTF®, HICKORY

WOODWORKING®, Homecraft®, HP FRAMER HIGH PRESSURE®, IMPACT SERIES™,

Innovation That Works®, Jet-Lock®, Job Boss®, Kickstand®, LASERLOC®, LONG-LASTING

WORK LIFE®, MAX FORCE™, MAX LIFE®, Micro-Set®, Midi-Lathe®, Monsoon®, MONSTER-

CARBIDE™, Network®, OLDHAM®, Omnijig®, PC EDGE®, Performance Crew™, Performance

Gear®, Pocket Cutter®, Porta-Band®, Porta-Plane®, Porter Cable®, Porter-Cable Professional

Power Tools®, Powerback®, POZI-STOP™, Pressure Wave®, PRO 4000®, Proair®, Quicksand

and Design®, Quickset II®, QUIET DRIVE TECHNOLOGY™, QUIET DRIVE TECHNOLOGY

AND DESIGN™, Quik-Change®, QUIK-TILT®, RAPID-RELEASE™, RAZOR®, Redefining

Performance®, Riptide®, Safe Guard II®, Sand Trap and Design®, Sanding Center®, Saw Boss®,

Shop Boss®, Sidekick®, Site Boss®, Speed-Bloc®, Speedmatic®, Stair Ease®, Steel Driver

Series®, SUPERDUTY®, T4 & DESIGN®, THE AMERICAN WOODSHOP®, THE

PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®, TIGERCLAW®, TIGERCLAW AND

DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®,

UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT

RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR

ACHIEVEMENT. OUR TOOLS.®

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may

also be registered in other countries. Other trademarks may apply.

4825 Highway 45 North

Jackson, Tennessee 38305

(888) 848-5175

www.portercable.com

90538674 PC600D Drill 10/1/08 9:24 AM Page 9

Manuel d'instructions

www.portercable.com

N° DE CATALOGUE

PC600D

Perceuse de 10 mm (3/8 po)

90538674 PC600D Drill 10/1/08 9:24 AM Page 10

Page is loading ...

Manual de'instrucciones

www.portercable.com

CATÁLOGO N°

PC600D

INSTRUCTIVO DE OPERACIÓN,

CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA.

ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL

PRODUCTO.

Taladro de 10 mm (3/8

pulgada)

90538674 PC600D Drill 10/1/08 9:25 AM Page 20

Page is loading ...

Catalog Numbers PC600D Form # 90538674

OCT. 2008 Printed in China

90538674 PC600D Drill 10/1/08 9:25 AM Page 32

Porter Cable 90538674 User manual

Brand: Porter Cable

Model: 90538674

Category: Power tools

Type: User manual

This manual is also suitable for

PC600D

Download PDF

report

in other languages

français: Porter Cable 90538674 Manuel utilisateur
español: Porter Cable 90538674 Manual de usuario

Porter Cable 90538674 User manual

This manual is also suitable for

Porter Cable 90538674 User manual

in other languages

Related papers

Other documents