Huffy 1051 User manual

Huffy
Brand
Huffy
Model
1051
Category
Fitness, gymnastics & weight training
Type
User manual
12/02 P/N 211670
1
Toll-Free Customer Service Number for U.S: 1-800-558-5234
Internet Address: http://www.hydra-rib.com
IMPORTANT! Have any questions?...Don’t go back to the store!
We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although
great care and effort have been taken, occasionally problems may occur. To ensure prompt and correct handling of any problems, or to
answer any questions, please contact our Toll-Free Customer Service Number listed below. Service will be quicker if you have your
Model Number (found on carton) and assembly instructions ready when calling. PLEASE WRITE YOUR MODEL NUMBER IN THE
SPACE PROVIDED ABOVE.
McCall's Rebounder
Owners Manual
© COPYRIGHT 2002 by HUFFY SPORTS
A Huffy Sports Company
Customer Service Center
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
WRITE IN YOUR MODEL NUMBER: 1051
SAFETY INSTRUCTIONS
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
• If using a ladder during assembly, use extreme caution.
• Two (2) people are recommended for this operation.
• Ensure there are no overhead power lines within 20 ft. (7 m) radius of system
location.
• Climate, corrosion, excessive use, or misuse could result in system failure.
• If technical assistance is required, contact Huffy Sports.
• Read and understand the warning label affixed to pole.
• The life of your basketball pole depends on many conditions. The climate,
placement of the pole, the location of the pole, exposure to corrosives such as
pesticides, herbicides or salts are all important.
• Adult supervision is recommended when adjusting height.
• Serious injury could occur if teeth/face come in contact with rebounder.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the
instructions carefully. Proper and complete assembly, use and supervision is
essential for proper operation and to reduce the risk of accident or injury. A
high probability of serious injury exists if this system is not installed,
maintained, and operated properly. Check entire box and inside all packing
material for parts and/or additional instructional material. Before beginning
assembly, read the instructions and identify parts using the hardware identifier
and parts list in this document.
For more information on assembly, placement, proper use and maintenance,
visit The American Basketball Council website at http://www.smarthoops.com.
REQUIRED TOOLS AND
MATERIALS:
• Minimum of 2 People
• Step Ladder 8 ft. (2.4m)
• (2) 7/16" Wrenches, 9/16" Wrenches, 3/4"
Wrenches, (1) 15/16" Wrench
or (2) Adjustable Wrenches
• (1) Standard and (1) Philip's Screwdriver
• 200 lbs. of ballast via (2) 100 lb.
Sand Bags.
2
P/N 211670 12/02
12/02 P/N 211670
PARTS LIST
(See Hardware Identifier)
Item
Qty. Part No. Description
1 1 200416 Base (Black)
2 4 200417 Casters
3 1 200419 Left Support Brace
4 1 201875 Right Support Brace
5 1 200423 Outer Pole Assembly
6 1 201876 Inner Pole, Fixed Upright
7 1 201877 T-Screw
8 1 200418 Collar
9 1 200421 Winch Handle
10 1 200409 Cable Assembly
11 1 200410 Winch
12 1 201878 Graduated Scale
13 1 201879 Indicator Bracket
14 1 201888 Rebound/Tip-in Indicator
15 1 200399 Hopper
16 1 200400 Rebound Arm
17 1 200401 Ball Check Mechanism
18 2 226023 Air-Checks
19 1 201880 Allen Wrench
20 8 206246 Bolt, Hex 1/2-13 X 1.5"
21 1 204453 Bolt, Hex 3/8-16 X 1"
22 18 201890 Screw, 3/4" Long
23 2 201881 Screw, Self-Tapping, 1/4" Long
24 1 201891 Nut, 5/8"
25 2 202459 Nut, 1/2-13,
26 3 203017 Nut, 3/8-16
27 16 203002 Nut, 1/4-20
28 1 201884 Lockwasher 1" O.D.
29 8 201886 Lockwasher, 7/8" O.D.
30 4 201885 Lockwasher, 3/4" O.D.
31 18 201887 Lockwasher, 1/2" O.D.
32 4 201882 Pin, Clevis
33 4 201883 Screw, Clevis
34 1 200402 1/2" Steel Shaft
35 2 300382 Sand Storage Bags
* YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.
McCall's REBOUNDER
REBOUND ARM
OUTER POLE
GRADUATED
SCALE
HOPPER
BASE
SUPPORT BRACE
WINCH
INNER POLE
COLLAR
TIP-IN
INDICATOR
WINCH HANDLE
SAND
BAGS
12/02 P/N 211670
3
HARDWARE IDENTIFIER
Item #20 (8)
Item #7 (1)
Item #21 (1)
Item #22 (18)
Item #23 (2)
Item #19 (1)
Item #32 (4)
Item #33 (4)
Item #24 (1)
Item #25 (2)
Item #26 (3)
Item #27 (16)
Item #28 (1)
Item #29 (8)
Item #30 (4)
Item #31 (18)
4
P/N 211670 12/02
12/02 P/N 211670
Tip base on it's side and install casters (2) to the bottom of base (1) as shown
using bolts (22), lockwashers (31) and nuts (27).
1.
22
2.
Attach collar (8) to outer pole (5) as shown with T-Screw bolt (7). Tighten
completely.
7
8
2
5
NOTE:
THE T-SCREW (7) IS USED TO SECURE
COLLAR TO OUTER POLE (5) UNTIL
STRUTS ARE ATTACHED (STEP 4).
AT THAT POINT THE
T-SCREW (7) CAN BE LOOSENED.
TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE. NOT
FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY
INJURY.
WARNING
6
31
27
SECTION A : ASSEMBLING THE McCALL'S REBOUNDER
12/02 P/N 211670
5
Attach pole assembly (5 & 6) to base (1) using bolts (20) and lockwashers (29) as
shown.
3.
20
29
TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE. NOT
FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY
INJURY.
WARNING
Attach left (3) and right (4) support braces to base (1) and then adjust collar (8) to
accommodate strut height. Attach braces (3 & 4) using bolts (20) and lockwashers
(29) as shown .
4.
20
20
25
20
25
29
29
29
3
4
4
3
6
P/N 211670 12/02
Attach graduated scale (12) to base (1) using bolt (21) and lockwasher (30)
as shown.
5.
4
3
2
1
7
11
10
4
3
2
1
7
1111
1010
21
30
12
Attach graduated scale (12) to bracket affixed to the collar (8) as shown with nuts
(25) and lockwashers (30).
6.
2
1
1212
1111
1010
9
25
12
8
30
1
12/02 P/N 211670
7
7.
Attach winch assembly (9, 10 & 11) to collar bracket using nut (25) and lockwasher
(30) as shown [Winch components (9, 10 & 11) are preassembled].
2
1
1212
1111
1010
9
25
9
IMPORTANT:
CORD MUST PASS BEHIND
SPACER AS SHOWN!
8.
Release the lever and unwind cable and attach top nut (25) and lockwasher (30)
to fully secure winch assembly to collar bracket as shown.
2
1
1212
1111
1010
9
25
Released
KEEP AWAY FROM
WINCH HANDLE WHEN
UNWINDING - THE
HANDLE WILL SPIN
WHEN CORD IS
UNWOUND!
WARNING
IMPORTANT:
DO NOT ATTACH
TOP NUT. ATTACH
BOTTOM NUT
ONLY.
30
30
Locked
10
11
TOP
BOTTOM
8
P/N 211670 12/02
13
22
14
13
14
12
Attach Rebound/Tip-in Indicator (14) to indicator bracket (13) while holding bracket
(13) in the position shown. The bracket/tip-in assembly (13 & 14) will not be secured
until the next step (#11).
10.
Hook Indicator Bracket (13) around the Graduated Scale (12). Do not attach
Rebound/Tip-in Indicator (14) yet, or the bracket will not fit around scale.
9.
12
13
12
13
12/02 P/N 211670
9
Attach unwound cord to indicator bracket (13) and bracket on outer pole (5)
using nut (24) and lockwasher (28) as shown.
11.
13
14
24
28
5
6
NOTE:
THIS STEP FUNCTIONS TO
RAISE THE OUTER POLE TO
ACCOMMODATE THE
DIFFERENT HEIGHTS
DENOTED ON THE TIP-IN
INDICATOR.
10
10
P/N 211670 12/02
Turn hopper (15) upside down and attach air checks (18) as shown by removing
and then re-inserting the retaining (33) and clevis (32) pins connected to the air
checks (18).
12.
18
33
33
32
32
NOTE
:
ITEMS (34 & 23) COME
PREASSEMBLED TO THE HOPPER
(15) BUT CAN BE REPLACED AND
ORDERED SEPARATELY.
23
23
34
16
12/02 P/N 211670
11
Slide Hopper assembly (15) over the top of the pole (5) tighten bolts indicated.
13.
15
Tighten completely
9/16" wrench needed
5
THE HOPPER IS HEAVY! TWO PERSON
MINIMUM REQUIRED FOR THIS PROCEDURE.
NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
DO NOT LEAVE ASSEMBLED UNIT
UNATTENDED WITHOUT SAND SUPPORT,
IT MAY TIP OVER.
WARNING
IMPORTANT!
DO NOT EMPTY SAND FROM
SAND BAGS INTO THE
STORAGE BAGS. PLACE
SEALED SAND BAGS
COMPLETELY INTO
STORAGE BAGS.
14
Place (2) 100 lb. sand bags (not included) into storage bags (35). Add bags to the
base as shown.
16
35
12
P/N 211670 12/02
BALL-CHECK MECHANISM - STANDARD POSTION
1. Ball-Check Mechanism (17) holding ball.
2. For normal operation, pull down on Rebound Arm (16) which causes Ball-Check
Mechanism (17) to drop, allowing ball to pass to arm.
3. Ball in arm position with Ball-Check Mechanism (17) holding next ball.
1.
SECTION B : OPERATING THE McCALL'S REBOUNDER
2.
Adjustment screw location
18
17
16
DRILLS REQUIRING BALL
TO PASS WITHOUT STOPPING
1. Revearse position of Ball-Check Release (17) and pull down on Rebound Arm
(16) until Ball-Check Mechanism (17) drops out of position.
16
17
BALL-CHECK MECHANISM - OUT OF POSITION
NOTE:
IF THE REBOUND ARM IS
RETURNING TOO FAST, OR IS
RETURNING TOO SLOW, THE AIR
CHECKS (18) MAY HAVE TO BE
ADJUSTED ACCORDINGLY.
NOTE:
TO RE-ENGAGE
BALL-CHECK MECHANISM,
REVERSE PROCEDURE IN
STEP 2
3.
12/02 P/N 211670
13
Adjust height by unlocking the winch lever (fig. A) and turning handle (9). Set winch
lever back to the locked position (fig. B) when desired height is attained.
LOCKED
UNLOCKED
1.
2
1
1212
1111
1010
9
HOLD ONTO HANDLE
BEFORE UNLOCKING.
THE WEIGHT OF THE
HOPPER AIDS IN THE
LOWERING OF THE
HEIGHT.
WARNING
SECTION C : ADJUSTING THE HEIGHT
Fig. BFig. A
9
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Huffy 1051 User manual

Huffy
Brand
Huffy
Model
1051
Category
Fitness, gymnastics & weight training
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents