Husqvarna 11 Bio User manual

Brand: Husqvarna

Model: 11 Bio

Category: Lawnmowers

Type: User manual

This manual is also suitable for

13 Bio
39765

101 91 58-26

Rider 11/13

Rider 11 Bio/13 Bio

Operator´s manual

Please read these instructions carefully and make sure

you understand them before using the machine.

English – 1

Operator’s Manual for

Rider 11 and Rider 13

Rider 11 Bio and Rider 13 Bio

Maintenance ......................................................19

Maintenance schedule ...................................19

Dismantling of the machine hoods.................20

Checking and adjusting the steering wires ....22

Checking and adjusting the brakes................23

Checking and adjustment of throttle wire.......24

Replacement of fuel filter ...............................24

Replacement of air filter .................................25

Checking the fuel pump’s air filter..................26

Checking the battery acid level ......................26

Checking the safety system ...........................27

Checking the tyre pressure ............................28

Checking the engine’s cooling air intake........28

Checking and adjusting the cutting unit

ground pressure.............................................29

Checking the parallelism of the cutting unit ...29

Adjusting the parallelism of the cutting unit....30

Service position for BioClip 90 .......................31

Checking the blades ......................................34

Replacing the break-pin .................................34

Changing the oil .............................................35

Lubrication.........................................................35

Checking the engine’s oil level.......................35

Checking the transmission’s oil level .............36

Lubricating the belt adjuster...........................36

General lubrication.........................................36

Lubrication of front wheel bearings ................37

Trouble shooting schedule ..............................38

Storage...............................................................39

Winter storage................................................39

Service ...........................................................39

Technical data ...................................................40

CONTENTS

IMPORTANT INFORMATION

Read through these instructions carefully so that you know how to use and maintain the

machine before using it.

For servicing other than described in this manual contact an authorised dealer for parts and

service.

Introduction .........................................................2

Driving and transport on public roads ..............2

Towing..............................................................2

Use...................................................................2

Serial number...................................................3

Explanation of symbols......................................4

Safety instructions..............................................5

General use .....................................................5

Driving on slopes .............................................6

Children............................................................7

Maintenance ....................................................7

Presentation ........................................................9

Location of the controls....................................9

Throttle/Choke lever.......................................10

Drive disengagement lever ............................10

Parking brake.................................................10

Throttle pedal ................................................. 11

Cutting unit.....................................................12

Lift lever for cutting unit..................................12

Lever for adjustment of cutting height............13

Seat................................................................13

Fuelling ..........................................................13

Driving................................................................14

Before starting................................................14

Starting the engine.........................................14

Driving the machine .......................................14

Cutting tips .....................................................17

Stopping the engine .......................................18

Drive disengagement lever ............................18

2 – English

INSTRUCTION

Dear customer

Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front-

mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency

even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission

(certain models) also contribute to the performance of this machine.

We hope you will find this operator’s manual very useful. By following its instructions (on operation, service,

maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value.

When you sell your Rider, make sure you pass on the operator’s manual to the new owner.

Travel and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the

machine on another vehicle always use approved securing devices and make sure that the machine is

securely held.

Towing

When your machine is equipped with a hydrostatic transmission you should, if necessary, only tow the

machine over short distances and at a low speed, otherwise there is a risk of damaging the transmission.

Intended use

This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled

ground without obstacles, as rocks, stumps etc., and, in conjunction with accessories supplied by the

manufacturer even for other special tasks for which instructions are delivered with the accessory. Use in any

other way is considered as contrary to the intended use. Compliance with and strict adherence to the

conditions of operation, service and repair as specified by the manufacturer also constitute essential

elements of the intended use.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular

characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational

medicine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any

resulting damage or injury

English – 3

SAFETY INSTRUCTIONS

Good service

Husqvarna products are sold all over the world and only through servicing dealers. This is to ensure that you,

the customer, get the best support and service. Before the machine is delivered it undergoes inspection and

is adjusted by your dealer.

When you need spare parts or advice on service issues, warranty terms, etc., contact:

This Operator’s Manual belongs to

machine with serial number:

Serial number

The serial number can be found on the printed plate attached to the front, left-hand side under the seat.

Stated on the plate, from the top are:

• The machines type designation.

• The manufacturer’s type number.

• The machine’s serial number.

State the type designation and serial number when ordering spare parts.

The engine number is punched on a plate that is riveted to the fan cover. The plate states:

• Model.

• Type.

• Code.

Please state these when ordering spare parts.

The transmission’s serial number is stated on the barcode decal located on the front of the housing on the

left-hand drive axle:

• Type designation is stated above the barcode and starts with the letter “K”.

• The serial number is stated above the barcode and has the prefix “s/n”.

• The manufacturer’s type number is stated under the barcode and has the prefix “p/n”.

State the type designation and serial number when ordering spare parts.

Engine Transmission

4 – English

These symbols are on the machine and in the operator’s manual.

Study them carefully so that you know what they mean.

Read the operator’s manual

Reverse Neutral Fast Slow Engine off Battery Choke Fuel

Oil pressure Cutting height Backwards Forwards Ignition Hydrostatic free wheel

Use eye and Clutch in Clutch out Parking brake Brake Clutch Warning

hearing protection

Soundlevel Warning! Warning! Never drive across a slope

Rotating blades. Risk that the machine can tip over

Never use the machine if persons,

especially children, or animals,

are in the vicinity.

Never carry passengers on the

machine or equipment.

Starting instructions

Read the instructions

Check the engine’s oil level

Check the hydrostat’s oil level

Lift up the cutting unit

Put the gear shift/hydrostat pedal in

neutral

Brake

If the engine is cold use the choke

Start the engine

Release the parking brake before

driving

Keep hands and feet away

from under the hood when

the engine is running.

EXPLANATION OF SYMBOLS

Speed limiter pedal forwards

Neutral

Speed limiter pedal reverse

Switch off the engine and take

off the ignition cable before

repairs or maintenance

Drive very slowly

without the cutting unit.

European standard for

machine safety

English – 5

RIDER

970

These instructions are for your safety. Read them carefully.

General use:

• Make yourself familiar with the controls and how

to stop quickly.

• Read all the instructions in Operator’s Manual

and on the machine before starting it. Make sure

you understand them, and then follow them.

• Only allow adults who are familiar with the

machine to use it.

• Wear approved protective glasses or a visor

during assembly and driving.

• Never use the machine barefoot. Always wear

heavy-duty shoes, preferably toe-capped.

• Never wear loose fitting clothes which can

fasten in moving parts.

• Clear the area of objects such as stones, toys,

and wires, etc. which can be caught up by the

blades and thrown out.

• Check that there are no other persons in the

area before starting to cut.

• Stop the machine if anyone comes into the work

area.

• Never carry passengers.

• Do not cut backwards unless absolutely neces-

sary.

• Always look down and behind before and during

reversing.

• Keep an eye on the ejected grass and do not

direct it towards anyone.

• Slow down before turning.

• Never leave the machine unattended when the

engine is running. Always switch off the blades,

pull on the parking brake, stop the engine and

take out the keys before leaving the machine.

• Switch off the blades when you are not cutting.

• Only cut in daylight or good artificial lighting.

• Never use the machine when you have con-

sumed alcohol, drugs, or certain medicines.

SAFETY INSTRUCTIONS

This symbol implies that important safety rules are applicable.

This is for your safety and the operating reliability of the machine.

RIDER

850

RIDER 850

RIDER

850

RIDER 850

RIDER

850

RIDER 850

RIDER

850

RIDER 850

Read the instructions before starting the machine.

Clear the area from stones etc. before cutting.

Never carry passengers.

WARNING!

This machine can cut off hands and feet, and eject objects.

Failure to follow the safety instructions can lead to severe injury.

6 – English

• Watch out for traffic when working close to a

road, or crossing one.

• Be careful when rounding a fixed object so that

the blades do not hit it. Never drive intentionally

over a foreign object.

• The machine is heavy and can cause very

severe crush injuries. Be extra careful when

loading it on a trailer or truck.

• Be careful when pulling a load or using heavy

equipment.

a. Only use approved tow hooks.

b. Limit the load to what you can manage safely.

c. Do not make sharp turns. Be careful when

reversing.

d. Use counterweights or wheel weights when

indicated in the instructions.

Driving on slopes

Driving on slopes is one of the situations where

there is the most serious risk that the driver can

loose control or that the machine tips over, which

can cause severe injuries or be fatal. All slopes

require extra care. If you cannot reverse up the

slope or if you feel uncertain avoid cutting it.

Do as follows:

• Remove obstacles such as stones and branches

etc.

• Cut upwards and downwards, not sideways.

• Look out for and avoid driving over furrows,

holes or mounds. On uneven surfaces it is

easier for the machine to tip over. High grass

can conceal obstacles.

• Drive slowly. Rider 11: Select a low gear to avoid

having to stop and changing gear. It is also

easier to use the gear to brake in a low gear.

• Follow the manufacturer’s recommendations on

wheelweights or counterweights to increase

stability.

• Take special care with accessories that can alter

the stability of the rider mower.

• Always drive smoothly and slowly on slopes.

Avoid sudden changes of speed or direction.

• Avoid starting or stopping on a slope. If the tyres

begin to skid switch of the blades and drive

slowly down the slope.

• Avoid unnecessary turns on slopes, and if

turning is necessary turn slowly and gradually,

downwards if possible.

SAFETY INSTRUCTIONS

850

RIDER

850

RIDER

850

RIDER

850

RIDER

850

Be extra careful when driving on slopes.

Cut slopes upwards and downwards, not sideways.

English – 7

• Do not cut close to edges, ditches or banks. The

machine can suddenly tip over if a wheel goes

over the edge of a drop or a ditch, or if a bank

gives way.

• Do not cut wet grass. It is slippery and the tyres

can loose their grip so that the machine slides.

• Do not try to stabilise the machine by placing

one foot on the ground.

Children

Tragic accidents can occur if the driver does not

pay attention to children in the vicinity. Children are

often attracted to the machine and the work of

mowing. Never assume that children stay where

you last saw them.

• Keep children away from the mowing area and

under the close supervision of another adult.

• Be on your guard and switch off the machine if

children come into the work area.

• Before and during reversing look behind and

down for small children.

• Never allow children to ride on the machine.

They can fall off and become seriously injured or

obstruct a risky manoeuvre of the machine.

• Never allow children to drive the machine.

• Be extra careful close to corners, bushes, trees

or other objects which obstruct your view.

Maintenance

• Petrol/gasoline and petrol/gasoline fumes are

toxic and highly inflammable. Be extra careful

when handling petrol/gasoline.

a. Store the fuel in containers approved for this

purpose.

b. Never fill up the machine with fuel when the

engine is running. Let the engine cool before

filling up with fuel. Do not smoke, or fill up with

fuel in the vicinity of naked flames or sparks.

Do not smoke. Do not fill fuel in the vicinity of

sparks or naked flames.

c. Never fill up with fuel indoors.

d. If leakage has occurred in the fuel system the

engine must not be started until this is rectified.

e. Never store the machine or fuel containers

indoors if there are naked flames, such as in a

boiler room or where there is electrical equip-

ment which can emit sparks.

• Check the fuel level each time before using the

machine, and leave space for the fuel to expand

since the heat from the engine and hot sun can

cause the fuel to run over.

SAFETY INSTRUCTIONS

RIDER

970

RIDER

850

RIDER 850

RIDER

850

RIDER 850

RIDER

850

RIDER 850

RIDER

850

RIDER 850

Keep children away from the mowing area.

Never allow children to drive the machine.

Never fill up with fuel indoors.

8 – English

• Avoid overfilling. If fuel has been spilt on the

Rider wipe it up and wait until it has evaporated

before starting the engine. If fuel is spilt on

clothes, change them.

• Be extra careful when handling battery acid.

Spilling acid on the skin can cause severe burn

injuries. Rinse immediately with water. If acid

gets into the eyes this can cause blindness.

Contact a doctor.

• Be careful with the maintenance of the battery.

Explosive gas is formed in the battery. Never

handle the battery when smoking or in the

vicinity of naked flames or sparks. Otherwise the

battery can explode and cause severe injuries.

• Never drive the machine in an enclosed space.

The exhaust fumes contain carbon monoxide,

an odourless, non coloured, toxic and fatal gas.

• Make sure that bolts and nuts, especially attach-

ment bolts for the blade units are properly

tightened and that the equipment is in good

order.

• Never alter the safety devices. Check regularly

that they function. The machine must not be

driven with defective or unmounted safety

devices.

• Do not alter the setting of the governor and do

not race the engine.

• Reduce the fire risk. Keep the machine clean

from grass, leaves and other refuse which

fastens in it. Allow the machine to cool before

placing it in the storage area.

• Stop and inspect the equipment if you drive over

an object. If necessary repair the machine

before starting.

• Never make adjustments with the engine run-

ning.

• The machine is tested for safety and approved

only for equipment supplied or recommended by

the manufacturer.

• The blades are sharp and can cause cutting

injuries. Wrap over the blades or use protective

gloves when handling them.

• Check the functioning of the brakes regularly.

Adjust and maintain them as necessary.

SAFETY INSTRUCTIONS

RIDER

850

RIDER 850

RIDER

850

RIDER 850

RIDER

970

Never smoke in the vicinity of the battery or the fuel.

Never drive the machine in an enclosed space.

Clean the machine regularly from grass, leaves and

other waste.

English – 9

Presentation

Congratulation on your choice of a first-class quality

product.

This manual describes four models that are fitted

with engines from Briggs & Stratton of 10.5 and

12.5 horsepower respectively.

PRESENTATION

Location of the controls

1. Ignition lock

2. Throttle/Choke lever

3. Adjustment of cutting height

4. Lifting lever, cutting unit

5. Speed control for reversing (only on 13 and 13

Bio)

6. Speed limiter for driving forwards on 13 and 13

Bio

Parking brake on 11 and 11 Bio

Rider 11 and Rider 11 Bio has an in-line gearbox

with five forward gears and one reverse gear.

On the Rider 13 and Rider 13 Bio the power trans-

mission from the engine is handled by a hydrostatic

gearbox which enables stepless variation of the

speed.

10 11

3 13

7. Parking brake on 13 and 13 Bio

Clutch pedal on 11 and 11 Bio

8. Lock button for parking brake (left side on 13

and 13 Bio, right side on 11 and 11 Bio)

9. Seat adjustment

10. Fuel tank cap

11. Main lock (under seat)

12. Lever for disengagement of drive (only on 13

and 13 Bio)

13. Gear lever on 11 and 11 Bio

10 – English

Throttle and Choke lever

The engine speed is adjusted with the throttle

control, and thereby also the rotation speed of the

blades.

The control is also used to activate the choke

function. When the choke is used the engine

receives a richer mixture of fuel and air, which

simplifies cold start.

PRESENTATION RIDER 11 / 11 BIO

Brake pedal / Parking brake

The brake pedal activates a disc brake which is

placed on the gearbox and brakes the drive wheels.

When braking the clutch pedal should also be

pushed down to achieve best braking power.

The brake pedal also operates as a parking brake if

the lock button is pressed in when the pedal is

pressed.

Clutch pedal

The clutch pedal disengages the engine and stops

forward movement.

The blades are

not

affected by the clutch pedal.

English – 11

PRESENTATION RIDER 13/13 BIO

Throttle and Choke lever

The engine speed is adjusted with the throttle

control, and thereby also the rotation speed of the

blades.

The control is also used to activate the choke

function. When the choke is used the engine

receives a richer mixture of fuel and air, which

simplifies cold start.

RIDER 850

Speed limiter

The speed of the machine is steplessly regulated

with two pedals. Pedal (1) is used to drive forwards

and pedal (2) for reversing.

Parking brake

The parking brake is applied as follows:

1. Press down the brake pedal.

2. Press in the lock button on the steering column.

3. Release up the brake pedal while holding the

button pressed.

The lock on the parking brake automatically discon-

nects when the brake pedal is pressed.

WARNING!

Make sure that branches do not

obstruct the pedals when mowing

under bushes, otherwise you may

lose control.

12 – English

RIDER 850

PRESENTATION

Cutting unit

Rider 11 and Rider 13 have a cutting unit with rear

ejection, i.e. the grass cuttings are thrown out

behind the cutting unit.

Lowering of the cutting unit (cutting position)

Rider 11 Bio and Rider 13 Bio have a twin-blade

BioClip cutting unit.

Lifting of the cutting unit (transport position)

Lift lever for cutting unit

The lift lever is used to set the cutting unit in trans-

port or cutting position.

If the lever is pulled back the unit will lift up and the

blades will automatically stop rotating (transport

position).

If the lock button is pressed and the lever is moved

forward the unit will be lowered and the blades will

automatically start rotating (cutting position).

The lever can also be used to temporarily regulate

the cutting height, e.g. for a small mound in the lawn.

English – 13

PRESENTATION

WARNING!

Petrol/gasoline is highly inflammable.

Observe care and fill up with fuel

outdoors (see safety instructions).

Fuelling

The engine should be run on 85 octane (or higher)

unleaded petrol/gasoline (no added oil). Environ-

mentally adapted alkylate fuel, such as Aspen, is

also recommended.

Lever for adjustment of cutting height

With this lever the cutting height can be adjusted to

9 different positions.

Cutting unit with rear ejection, 40-90 mm.

BioClip cutting unit, 45-95 mm.

Seat

The seat has a jointed attachment on the front

edge and can be tipped forward.

The seat can also be adjusted lengthways.

Release the knobs under the seat and adjust it

forwards or backwards to the required position.

Lock the adjustment with the wheels.

Rider 13

14 – English

Before starting

• Read the safety instructions and information on

the location and function of the controls before

starting (see pages 5–13).

• Conduct daily maintenance before starting (see

maintenance schedule on page 19).

Adjust the seat to the required position.

Starting the engine

1. Lift up the cutting unit by pulling the lever back-

wards to locked position (transport position).

DRIVING

3. For Rider 11 and Rider 11 Bio: Set the gear

lever to position “N” (neutral).

2. Apply the parking brake. This is done as follows:

• Press down the brake pedal (1).

• Press in the lock button on the steering

column (2).

• Release the brake pedal while the button is

held pressed.

The parking brake lock disconnects automati-

cally when the brake pedal is pressed down.

On the Rider 11 and Rider 11 Bio the brake

pedal and lock button are on the right side.

Rider 13

Rider 11

IMPORTANT INFORMATION

Do not press the reverse lock button on

the lever when you select neutral. If you

do, it could trigger the start lock.

English – 15

DRIVING

Warm engine:

5. Set the throttle control midway between position

1 and 2.

STOP START

IMPORTANT INFORMATION

Do not run the starter for more than about

5 seconds at a time. If the engine does not

start, wait about 10 seconds before trying

again.

6. Turn the ignition key to start position.

Cold engine:

4. Push the throttle control to position 3 (choke

position). In this position the engine receives a

richer mixture so that the engine starts more

easily.

16 – English

RIDER 850

2. For Rider 13 and Rider 13 Bio

Carefully press down one of the pedals until the

correct speed is reached.

To drive forwards: press down pedal (1).

To reverse: press down pedal (2).

For Rider 11 and Rider 11 Bio

Press the clutch and engage the required gear.

To engage reverse gear the lock button must be

pressed down.

• Gears 1–4 are used for mowing.

• Gears 4–5 are used for transport.

Starting is possible irrespective of which gear is

engaged.

DRIVING

STOP START

WARNING!

Never run the engine indoors, in

enclosed or poorly ventilated areas.

The exhaust fumes contain toxic

carbon monoxide.

7. When the engine has started release the ignition

key to neutral position.

Push the throttle control to the required speed.

For cutting 3/4 to full throttle.

Driving the machine

1. Release the parking brake by pressing down the

brake pedal.

IMPORTANT INFORMATION

Do not change gear from forward drive to

reverse while the machine is moving.

The clutch must be used for each gear

change.

Stop the machine before changing for

forward drive to reverse, otherwise the

gearbox can be damaged.

Never

use force to engage a gear. If a gear

will not engage directly release and push

down the clutch again, and then try to

engage the gear again.

Rider 13

Rider 11

English – 17

3. Select the required cutting height (1-9) with the

cutting height lever.

To obtain a uniform cutting height it is important

that the tyre pressures are equal on both front

wheels (60 kPa).

4. Push in the lock button on the lift lever and lower

down the cutting unit.

IMPORTANT INFORMATION

The service-life of the drive belts increases

considerably if the engine is run at low

speed when engaging the blades. For this

reason do not increase the throttle until

the cutting unit has been lowered to the

cutting position.

Cutting tips

• Localise and mark stones and other fixed objects

to avoid collision.

• Start with a high cutting height and reduce down

until the required cutting result are obtained.

• The cutting results are best with a high engine

speed (fast rotating blades) and low driving

speed (slow moving machine). If the grass is not

too high and thick the driving speed can be

increased or the engine speed reduced without

noticeably affecting the mowing results.

Mowing pattern

DRIVING

• The best lawns are achieved if the grass is cut

often. Mowing becomes more uniform and the

grass cuttings become more evenly distributed

over the surface. The total time consumption is

not greater since it is possible to select a higher

driving speed without inferior mowing results.

• Avoid mowing a wet lawn. The mowing results

are inferior since the wheels sink down into the

soft lawn.

• Hose down the cutting unit with water

underneath each time it is used. Put the cutting

unit in the service position first.

• If you use the BioClip unit it is important to mow

the grass regularly.

WARNING!

Clear the lawn from stones and

other object which can be thrown

out by the blades.

18 – English

DRIVING

WARNING!

Never drive the machine on

ground with a slope of more than

15°. Mow slopes upwards and

downwards, never across. Avoid

sudden changes in direction.

2. Rider 11 and Rider 11 Bio: Pull back the

throttle control and put the gear lever into

neutral “N” without pressing the reverse lock

button. Turn the ignition key to the “STOP”

position.

Rider 13 and Rider 13 Bio: Pull back the

throttle lever and turn the ignition key to the

“STOP” position.

3. When the rider mower is stationary, hold down

the parking brake and push in the lock button.

STOP START

Release lever Rider 13 and Rider 13 Bio

In order to move the machine when the engine is

switched off the release lever must be pressed

down and forwards.

Hill start, manual gearbox

1. Press down the parking brake.

2. Push the throttle control to 3/4 position to full

throttle position.

3. Push down the clutch and engage first gear.

4. Carefully release the clutch.

5. When the engine starts to pull, release the parking

brake.

Stopping the engine

Preferably allow the engine to idle for a minute to

obtain normal working temperature before stopping

it if it has been working hard.

1. Lift up the cutting unit by pulling the lever back

to the end position.

MAX 15°

English – 19

WARNING!

No service procedures must be conducted on the engine or cutting unit unless:

• The engine is switched off.

• The ignition key is removed.

• The ignition cable is removed from the plug.

• The parking brake is applied.

• The cutting unit is disengaged.

Maintenance

5025

100

MAINTENANCE

Page

Maintenance interval

in hours

Daily

mainte-

nance

before start

Maintenance schedule

The following is a list of the maintenance which should be conducted on the machine. For the items which

are not described in these instructions go to an authorised service workshop.

Check the engine’s oil level 35 ●

Check the engine’s cooling air inlet 28 ●

Check the fuel pump’s air filter 26 ●

Check the steering wires 22 ●

Check the brakes 23 ●

Check the battery 26 ●

Check the safety system 27 ●

Check screws and nuts – ❍

Check for fuel and oil leakage – ❍

Change the engine oil

35 ●

Clean the air filter’s pre-filter (foam plastic)

25 ●

Check the cutting unit 29 ●

Check the tyre pressures (60 kPa) 28 ●

Lubricating the belt adjuster

36 ●

Lubricate joints and shafts

37 ●

Adjust the brakes – Rider 11 and Rider 11 Bio 23 ●

Check the V-belts – ❍

Check the transmission’s cooling flanges –– ❍

Rider 13 and Rider 13 Bio

Check the transmission’s oil level – Rider 13 and 36 ●

Rider 13 Bio

Adjust the brakes – Rider 13 and Rider 13 Bio 23 ●

Check and adjust the throttle wire 24 ●

Clean the cooling flanges on the engine and – ❍

transmission

2,4)

Replace the air filter’s pre-filter and paper filter

25 ●

Replace the fuel filter 24 ●

Replace the plug – ❍

● = Described in these instructions.

❍ = Not described in these instructions.

First change after 5 hours.

During dusty conditions cleaning and replacement should be more frequent.

For daily use of the

machine lubrication should be conducted twice a week.

Conducted by authorised service workshop.

Page is loading ...

Husqvarna 11 Bio User manual

Brand: Husqvarna

Model: 11 Bio

Category: Lawnmowers

Type: User manual

This manual is also suitable for

13 Bio
39765

Download PDF

report

Husqvarna 11 Bio User manual

This manual is also suitable for

Husqvarna 11 Bio User manual

Related papers

Other documents