Hunter 32200 User manual

www.hunterfan.com

Evaporative Humidier

Model 32200, 38200

Read and save these instructions.

ENGLISH

See page 2

ESPAÑOL

Vea la página 13

READ AND SAVE THESE INSTRUCTIONS

How The Hunter®

Evaporative Humidier Works

Important Safety Instructions:

Read all instructions before

using this humidier.

1. This humidifier may not work properly

on an uneven surface. ALWAYS place this

humidier on a rm, level, and water resis-

tant surface. ALWAYS place the humidier

at least six (6) inches away from walls and

heat sources such as stoves, radiators, or

heaters.

2. ALWAYS place the humidier in an area that

is out of the reach of children.

3. Before using the humidier, extend the cord

and inspect for any signs of damage. DO

NOT use the product if the cord has been

damaged.

4. This product has a polarized plug (one

blade is wider than the other) as a safety

feature. This plug will t into a polarized

outlet only one way. If the plug does not t

fully into the outlet, reverse the plug. If it still

does not t, contact a qualied electrician.

DO NOT attempt to defeat or override this

safety feature.

5. ALWAYS UNPLUG AND EMPTY the humidi-

er when it is not in operation or while it is

being cleaned.

6. DO NOT tilt or move the humidier while it

is in operation. Never move the humidier

while there is water in the tank. Empty the

water tank, turn o, and unplug the unit

before moving.

7. In addition to routine maintenance which

may be required, this humidier requires

seasonal cleaning. Refer to and follow

CLEANING THE HUMIDIFIER AND THE WA-

TER TANK instructions.

Thank you for purchasing The Care Free

®

Humidifier Evaporative Humidifier by

Hunter Fan Company. Please read and save

these instructions to receive the maximum

benet and performance from your humidi-

er.

The Hunter® Evaporative Humidier has a unique patented design with several innovative features:

• Built-inAntimicrobialProperties–Theplasticpartsandthelterhavebuilt-inantimicrobialprop-

erties to inhibit the growth of bacteria, mold and fungi that may aect these parts.

 • NoWhiteDust–TheHunter® Evaporative Humidier produces no white dust that can settle on

furniture or be inhaled.

NOTE: This product contains antimicrobial properties which are built-in to inhibit the growth of

bacteria which may aect the plastic and lter in the humidier. These properties do not extend

to the water, humidied air or users. Conduct routine cleaning and maintenance based upon use

and individual conditions.

NOTE: You may notice mineral deposits accumulating in the tank base. This is normal and does

not aect performance. If you would like to clean these deposits away, please see CLEANING THE

HUMIDIFIER AND WATER TANK.

Humidier Parts

Figure 1

Base

Wick

Water Tank

Main Housing

Tank Tote

Tank Fill Cap

Power/Speed

Control

Figure 2

Using Your Humidier

1. Remove the Hunter® Evaporative Humidier from its packaging.

2. Place the humidier on a hard, at, water resistant surface. Always place the humidier at least

six (6) inches away from walls and sources of heat.

3. Make sure the Power/Speed Control is in the ‘OFF’ position. NOTE: The Power/Speed Control should

always be o before unplugging the humidier, moving the humidier, or relling the water tank.

See Figure 2.

Figure 3

Wick, properly

seated

O

F

4. Lift the Main Housing to ensure the Wick is properly seated, resting on the bottom of the base and

not tilted or otherwise out of position. See Figure 3. Place the Main Housing back on the Base.

Power/Speed Control

4. Grasp the Water Tank by its Tank Tote and remove it from the Base.

5. Turn the Water Tank upside-down and remove the Tank Fill Cap. See Figure 4.

Twist to open

Figure 4

6. Fill the Water Tank with water, return the Tank Fill Cap to its position and tighten it, and return the

Water tank to the Base.

7. Plug the humidier’s Power Cord into a standard household power outlet.

8. Turn the Power/Speed Control to your desired humidier fan speed. See Figure 5.

O

F

Figure 5

Cleaning The Humidier And The Water Tank

Relling The Water Tank

1. When the water tank level is low, turn the humidier ‘OFF’, and unplug.

2. Remove the tank and take it to the sink or tub to rell.

3. Turn the tank upside down and unscrew the tank cap by turning it counterclockwise. Empty the tank,

rell with fresh cool water (never use hot water), and replace the tank cap. Be sure not to overll the

tank as water damage may occur to furniture or ooring due to spillage. HUNTER WILL NOT ACCEPT

RESPONSIBILITY FOR DAMAGE TO PROPERTY CAUSED BY WATER SPILLAGE.

4. Carry the tank back to the humidier. Turn the tank upright and place it on the humidier. Be sure

that the tank is seated properly in the base. If the tank is properly located on the base, you will

see air bubbles owing up into the tank.

Many regions have hard water with high concentrations of minerals. When water evaporates from The

Hunter® Evaporative Humidier, minerals may be left behind. These minerals can form a hard white

scale which can be removed by following the cleaning instructions. The frequency of cleaning due

to mineral build up can vary depending upon the quality of water you may have.

Refer to Figure 1 for part names.

1. Turn the humidier ‘OFF’ and unplug the unit.

2. Lift the main housing and remove the water dispersion tray and the wick. The motor is attached

to the main housing. Do not place the motor near water. Do not use a wet towel on the motor or

motor housing as electrical shock may occur.

3. Replace the humidier’s wick every 4 - 8 weeks or when it has turned brown.

4. Remove the water tank from the base and empty any water that is left in the tank. Soak the base

in a mixture of one (1) gallon of water and eight (8) ounces of vinegar for 20 minutes. The base is

dishwasher safe.

5. After soaking, wipe the base with a soft cloth or sponge to remove any mineral build up. Rinse

with clean water several times. If you are planning on storing the humidier, be sure the base

is completely dry.

6. Fill the water tank with one (1) gallon of water and eight ounces of undiluted white vinegar. Re-

place the tank cap and shake the tank vigorously until all interior surfaces of the tank have been

exposed to the water/vinegar mixture.

7. Empty the tank of the water/vinegar mixture. Rinse it several times with clean water and then

replace the tank cap. If you are planning on storing the humidier, dry it inside and out, leaving

the cap o to allow the tank to completely dry. Continue to clean the other parts of your humidi-

er.

8. Wipe the surfaces of the main housing with a soft cloth.

9. Once all the parts are clean, reassemble the humidier, and follow the USING YOUR

HUMIDIFIER to continue use. If you are storing the humidier, make sure the parts are completely

dry, reassemble, and store in a dry location.

NOTE: The humidier’s Wick is made of paper and is NOT washable.

Over time, minerals in your water will build up in the humidier’s Wick, degrading its ability to absorb

water and reducing the humidier’s output. Therefore, you should replace the humidier’s Wick every

4 - 8 weeks, depending on the hardness of your water.

1. Turn the humidier ‘OFF’ and unplug the unit.

2. Lift the Main Housing, remove it from the Base, and set it aside.

3. Grasp the humidier Wick, hold it over the base, and squeeze the water from it. This will keep

water from dripping onto your oor. You may also want to wrap the Wick in a towel to keep it

from dripping while you transport it to disposal.

4. Replace the old Wick with a new Hunter humidier Wick, number 31911. New Wicks are available

at your local Hunter retailer or at www.hunterfan.com.

5. Ensure the Wick is properly seated, resting on the bottom of the base and not tilted or otherwise

out of position.

6. Return the Main Housing to its position on the Base. Make certain the Main Housing is properly

seated on the Base.

7. Plug the humidier’s Power Cord into a standard household power outlet and turn the Power/Speed

Control to your desired setting.

Replacing the Humidier Wick

To obtain a service part for your humidier, call customer service at 1-888-830-1326 or e-mail us at

techsupport@hunterfan.com. Please be prepared to tell the operator the model number of your

humidier and the name of the part you need to replace and the part number. Refer to Figure 1 for

part names.

Service Parts

32200

Model No.

Base

Water

Tank

Knob A

Tank Cap

Filter

31911

97676

97678 76257

87843

To learn more about Hunter Fan Company products, please see our web page at:

www.hunterfan.com

Other Home Comfort Products from Hunter

Hunter Original

®

QuietFlo™

True HEPA Air Purier

Programmable

Thermostat

Page is loading ...

HUNTER FAN COMPANY

2500 FRISCO AVENUE

MEMPHIS, TN 38114, USA

Hunter 32200 User manual

This manual is also suitable for

Hunter 32200 User manual

in other languages

Related papers

Other documents