Haier CHDE 5000 AW User manual

User Manual and Installation Instructions

Gas & Electric Dryer

Sécheuses à chargement frontal à gaz et

électrique

Manual para el usuario e instrucciones

de instalación. Secadora a gas y eléctrica

Model, Modéle, Modelo

HDE5000AW, HDG5000AW ; HDE5300AW, HDG5300AW

CHDE5000AW; CHDE5300AW

Quality

n

Innovation

n

Style

(Picture for illustration purposes only. Actual model may vary per model purchased.)

Front Load Dryers

1

English

PAGE

IMPORTANT SAFETY INSTRUCTIONS .......................................2-4

INSTALLATION INSTRUCTIONS ..............................................5-19

Tools and Materials Required ............................................................ 5

Electrical Requirements ..................................................................5-6

Unpacking Your Dryer ..................................................................... 6

Exhaust System Requirements ........................................................7-8

Gas Supply Requirements ................................................................ 9

Location of Your Dryer ...................................................................10

Location of Your Dryer in a Closet....................................................11

Manufactured (Mobile) Home Instruction .........................................12

Changing the Drum Light ................................................................13

Electrical Installation ......................................................................14

3-Wire Cord Connections ..............................................................15

4-Wire Cord Connections ..............................................................16

Gas Connections .......................................................................... 17

Replacement Parts .........................................................................19

OPERATING INSTRUCTIONS ............................................... 20-33

Understanding the Control Panel

(HDE/HDG5300AW, CHDE5300AW) . 20-22

Understanding the Control Panel

(HDE/HDG5000AW, CHDE5000AW) . 22-24

Preparations before Drying .............................................................25

Load clothes into Dryer ...................................................................26

Auto Dry Cycle

(HDE/HDG5300AW, CHDE5300AW) ......................... 27-28

Auto Dry Cycle

(HDE/HDG5000AW, CHDE5000AW) ...............................29

Manual Dry Cycle

(HDE/HDG5300AW, CHDE5300AW) ...........................30

Manual Dry Cycle

(HDE/HDG5000AW, CHDE5000AW) ...........................31

Rack Dry Cycle

(HDE/HDG5300AW, CHDE5300AW) ...............................31

Rack Dry Cycle

(HDE/HDG5000AW, CHDE5000AW) ...............................32

Other Features ............................................................................... 32

Normal Operating Sounds ..............................................................33

CARE AND CLEANING GUIDE

.......................................................33

TROUBLESHOOTING .................................................................. 34

LIMITED WARRANTY .................................................................35

TABLE OF CONTENTS

2

English

IMPORTANT SAFETY INSTRUCTIONS

Before beginning installation, carefully read these instructions. This will simplify

the installation and ensure the dryer is installed correctly and safely.

NOTE: The electrical service to the dryer must conform with local codes and

ordinances and the latest edition of the National Electrical Code, ANSI/

NFPA 70 or in Canada, CSA C22.1 Canadien Electrical Code Part 1.

NOTE: The gas service to the dryer must conform with local codes and

ordinances and the latest edition of the National Fuel Gas Code, ANSI

Z223.1 or in Canada, CAN/CGA B149.1.

NOTE: The dryer is designed under ANSI Z21.5.1 or ANSI/UL 2158 - CAN/

CSA C22.2 No. 112-97 (latest editions) for HOME USE ONLY. This

dryer is not recommended for commercial application such as restaurants,

beauty salons, etc.

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

For your safety the information in this manual must be

followed to minimize the risk of fire or explosion or to

prevent property damage, personal injury or loss

of life.

Combustible materials, gasoline, and other flammable vapors and

liquids must not be stored near the dryer.

WHAT TO DO IF YOU SMELL GAS

1. Do not try to light any appliance

2. Do not touch any electrical switch. Do not use any phone in

your building.

3. Clear the room, building, or area of all occupants.

4. Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

5. If you cannot reach your gas supplier, call the Fire Department.

Installations must be performed by a qualified or licensed

contractor, plumber, or gasfitter qualified or licensed by the state,

province, or region where this appliance is being installed.

English

IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of fire, electric shock, or

injury to persons when using your appliance, follow the

basic precautions, including the following:

1. Read all of the instructions before using this appliance.

2. Don’t dry articles that have been previously cleaned in, washed in,

soaked in, or spotted with gasoline, dry clean solvents or other

flammable explosive sub stains as they give off vapors which could

ignite or explode.

3. Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is used near

children.

4. Before the appliance is removed from service or discarded, remove the

door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to water

and/or to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any

servicing unless specifically recommended in the user-repair

instructions that you understand and have skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

10. Do not use heat to dry articles or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

11. Clean lint screen before or after each load.

12. Keep area around the exhaust opening and adjacent surrounding

areas free from the accumulation of lint, dust and dirt.

13. Keep the dryer area clear and free from items that would obstruct

the flow of combustion and ventilation air through the louvered panel

located on the rear of the dryer.

14. The interior of the appliance and the exhaust duct should be cleaned

periodically by qualified service personnel.

3

English

4

Thank you for using our Haier

product. This easy-to-use manual

will guide you in getting the best

use of your dryer.

Remember to record the model and

serial number. They are on a label

in back of the dryer.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

15. Do not place items exposed to cooking oils in your dryer. Items

contaminated with cooking oil may contribute to a chemical reaction

than could cause a load to catch fire.

16. If material has been used with any flammable liquids or solids, it

should not used in the dryer until all traces of flammable liquids and its

fumes have been removed.

17. This dryer must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions in

the installations sections.

18. Proper grounding must be ensured to reduce the risk of electric shock

and force. Check with a qualified electrician or service personnel if

you are in doubt as to whether the dryer is properly grounded.

19. Use the dryer only for its intended purpose: drying clothes.

20. Always disconnect dryer from electrical supply before attempting any

service. Disconnect power cord by grasping the plug, not the cord.

21. Replace worn power cord and/or loose plugs.

22. To reduce the risk of electric shock or fire, do not use extension cords

or adapters to connect dryer electrical power source.

SAVE THESE

INSTRUCTIONS

DANGER

Risk of child entrapment. Before you throw away your old dryer,

take off the door so that children may not get trapped inside.

5

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

Risk of Fire:

1. Clothes dryer installation must be performed by a qualified installer.

2. Install the clothes dryer according to the manufacturer’s instructions and local

codes.

3. Do not install a clothes dryer with flexible plastic venting materials. If flexible

metal (foil type) duct is installed, it must be of a specific type identified by the

appliance manufacturer as suitable for use with clothes dryers. Flexible

venting materials are known to collapse, be easily crushed and trap lint. These

conditions will ostruct clothes dryer airflow and increase the risk of fire.

4. To reduce the risk of severe injury or death, follow all installation instructions.

Tools and materials required

• Phillips-Head and flathead screwdrivers

• Channel-lock adjustable pilers

• 1/2-inch open-end wrench

• Carpenter’s level

• Measuring tape (12ft. min.)

• Duct tape

• Pipe thread sealer (Gas)

• Rigid or flexible metal 4 inch (102cm) duct

• Vent hood

Safety Warning:

1. Before starting installation, make sure that the gas shut off valve is in the

off position.

2. All old gas connectors and gas piping should be discarded.

ELECTRICAL REQUIREMENTS (Electric Dryers)

Model Numbers:

(CHDE/HDE5000AW and CHDE/HDE5300AW)

C ircuit

Individual 30 Amp branch circuit fused with 30 Amp time-delay fuses or circuit

breakers.

INSTALLATION INSTRUCTIONS

English

WARNING

English

6

P ower Supply

3 or 4 wire, 120/240 Volt, 1 Phase, 60Hz, AC

P ower Supply Cord Kit

(Not supplied when sold in US. Must be purchased to meet local electrical

codes.) The dryer MUST employ a 3-conductor power supply cord NEMA 10-30

Type SRDT rated at 240 Volt AC minimum, 30 Amp, with 3 open end spade lug

connectors with upturned ends or closed loop connectors and marked for use

with clothes dryers.

(When sold in Canada - 4-wire power supply cord provided and

attached on dryer)

Dryers being installed in a manufactured (mobile) home MUST employ a

4-wire power supply cord NEMA 14-30 type SRDT or ST (as required) rated

to 240 Volt AC minimum, 30 Amp, with 4 open-end spade lug connectors

with upturned ends or closed loop connectors and marked for use with clothes

dryers. See Electrical Connections for more information on a 4-wire system.

O utlet Receptacle

NEMA 10-30R receptacle should be located so the power supply cord is

accessible when the dryer is in the installed position. (Canada - NEMA 14-30R

receptacle)

ELECTRICAL REQUIREMENTS (Gas Dryers)

Model Numbers:

(HDG5000AW and HDG5300AW)

C ircuit

Individual 15 Amp branch circuit fused with 15-Amp maximum time delay fuse

or circuit breakers.

P ower Supply

3 wire, 120 Volt, 1 Phase, 60Hz, AC

P ower Supply Cord

The dryer is equipped with a 120 Volt 3-wire power supply cord.

NOTE: This dryer is equipped with a three-prong grounding plug for your

protection against shock hazard and should be plugged into a properly

grounded three-prong receptacle. Do not under any circumstance cut or

remove grounding prong from plug.

Unpacking Your Dryer

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packaging, tape or printed materials

before using the dryer.

The following are specific requirements for

proper and safe operation of your dryer. Failure

to follow these instructions can create excessive

drying times and fire hazards.

1. Do not use plastic flexible duct to exhaust the dryer. Excessive lint can build up

inside exhaust system and create a fire hazard and restrict air flow. Restricted

air flow will increase drying time. If your present system is made up of plastic

duct or metal foil duct, replace it with a rigid or flexible metal duct. Ensure

present duct is free of any lint prior to installing dryer duct.

2. The dryer must not be exhausted into any gas vent, chimney, wall, ceiling or

any concealed space of a building. The dryer exhaust system MUST be

exhausted to the outdoors. If the dryer is not exhausted outdoors, some

fine lint will be expelled into the laundry area. An accumulation of lint in any

area of the home can create a health and fire hazard.

3. Exceeding the length of duct pipe or number of elbows allowed in the

“Maximum Length” chart can cause an accumulation of lint in the exhaust

system. Plugging the system could create a fire hazard, as well as increase

drying times.

4. Do not screen the exhaust ends of the vent system. Lint can become caught in

the screen, increasing drying time. Use an approved vent hood to terminate the

duct outdoors, and seal all joints with duct tape.

5. All male duct pipe fittings must be installed downstream with the flow of air.

6. Exhaust duct must not be connected or secured with screws or other fastening

devices which extend into the interior of the duct.

7. Do not allow combustible material (clothing, draperies/curtains, paper, etc.) to

come in contact with exhaust system.

Explosion hazard:

Do not install the dryer where gasoline or other flammables are kept or

stored. Failure to do so can result in death, explosion, fire or burns.

Exhaust Requirements:

Use only rigid of flexible metal duct and approved vent hood which has a swing-

out damper hat open when the dryer is in operation. When the dryer stops, the

dampers automatically close to prevent drafts and the entrance of insects and

rodents. To avoid restricting the outlet, maintain a minimum of 12 inches (30.5cm)

clearance between the vent hood and the ground or any other obstruction.

The vent flap should be able to move freely, although vertical orientation of the

exhaust system is acceptable. Certain extenuating circumstances could affect the

performance of the dryer:

WARNING

EXHAUST SYSTEM REQUIREMENTS

English

7

1. Only rigid metal duct work should be used.

2. Venting vertically through a roof may expose the exhaust system to down

drafts causing an increase in vent restriction.

3. Running the exhaust system through an uninsulated area may cause

condensation and faster accumulation of lint.

4. Compression of crimping of the exhaust system will cause an increase in

vent restriction.

5. In Canada, that only those foil-type flexible ducts, if any, specifically identified

for use with the appliance by the manufacturer shall be used. In the United

States, that only those foil-type flexible ducts, if any, specifically identified

for use with the appliance by the manufacturer and that comply with the UL

Outline for clothes Dryer Transition Duct, Subject 2158A (2006), shall be

used.

6. In Canada, that the exhaust duct shall be 102 mm in diameter. In the United

States, the required exhaust duct diameter.

The exhaust system should be inspected and cleaned a minimum of every 12

months with normal usage. The more the dryer is used the more often you should

check the exhaust system and vent hood for proper operation.

Side and Bottom Exhaust

For your convenience, your dryer can be exhausted through the side or the

bottom. If you need to change the exhaust on the dryer to the side or the

bottom of the cabinet, you will need to order the exhaust kit from your Haier

dealer or call 1- 800-313-8495

English

8

RECOMMENDED MAXIMUM

Exhaust Hood Types

Recommended

Use only for short

run installations

No. of 90º

elbows

Rigid Metal Rigid Metal

0 90 ft. 60 ft.

1 60 ft. 45 ft.

2 45 ft. 35 ft.

3 35 ft. 25 ft.

The total length of ﬂexible metal duct shall not exceed

94 inches.

GAS SUPPLY REQUIREMENTS

English

9

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

Replace copper connecting pipe that is not plastic

coated. Stainless steel or plastic-coated brass

MUST be used.

1. Installation MUST conform with local codes. In the absence of local codes,

installation must conform with the National Fuel Gas Code, ANSI Z223.1

(latest edition) or in Canada, the current CAN/CGA B149.1

2. The gas supply line should be 1/2 inch (1.27cm) pipe.

3. If codes allow, flexible metal tubing may be used to connect your dryer to the

gas supply line. The tubing MUST be constructed of stainless steel or plastic-

coated brass.

4. The gas supply line MUST have an individual manual shutoff valve installed

within 6 feet (183cm) of the dryer in accordance with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54.

In Canada, an individual manual shut-off valve MUST be installed in

accordance with the B149.1, Natural Gas and Propane Installation Code.

5. A 1/8 inch (0.32cm) N.P.T. plugged tapping, accessible for test gauge

connection, MUST be installed immediately upstream of the gas supply

connection to the dryer.

6. The dryer MUST be disconnected from the gas supply piping system during

any pressure testing of the gas supply piping system at test pressures in excess

of 1/2 psig (3.45kPa).

7. The dryer MUST be isolated from the gas supply piping system during any

pressure testing of the gas supply piping system at test pressures equal to or

less than 1/2 psig (3.45 kPa).

English

10

Do Not Install Your Dryer:

1. In an area exposed to dripping water or outside weather conditions.

2. In an area where it will come in contact with curtains, thick carpet, or

anything that will obstruct the flow of combustion and ventilation air.

3. On carpet, floor must be solid with a maximum slope of 1inch (2.54 cm). Any

floor unevenness should be corrected with leveling legs located on the bottom

of the dryer.

Installation in Alcove or Closet:

1. DO NOT install your dryer in a closet with a solid door.

2. A dryer installed in a bedroom, bathroom, alcove or closet MUST be

exhausted outdoors.

3. No other fuel burning appliance shall be installed in the same closet as the

gas dryer.

4. Refer to the images on this page to ensure the installation provides the

minimum amount of clearance required for ventilation.

5. When installing the dryer in a closet with a door, a minimum of 120 square

inches (774.2 square cm) of ventilation in the door is required. Openings must

be equally divided at the top and bottom of the door and airflow must be

unobstructed. A louvered door with equivalent air openings for the length of

the door is acceptable.

LOCATION OF YOUR DRYER

8

2

5

m

6

8

6

m

101 0mm

1295mm(51”)

960mm( 37-13/16“)

39-3 /4”

2

7

”

3

2

-

1

/

2

”

English

Following are instructions concerning and the minimum clearances required for

any closet, recessed area, or customized under-counter installation:

• Additional distances facilitate installation and servicing.

• Addtional clearances might be required for wall, door and floor moldings.

• Additional distances of 1 in. (25.4mm) on all sides of the dryer is

recommended to reduce noise transfer.

• For closet installation with a door, minimum ventilation openings in the top

and bottom of the door are required. Louvered doors with equivalent ventilation

openings are acceptable. Companion appliance spacing should be

considered.

LOCATION OF YOUR DRYER IN A CLOSET OR RECESSED AREA

11

32.5"

1 5 "

1

"

3

"

( 5. 4mm)

2

( mm )(8 25m m)

( 38.1 mm )

3"

(76mm)

3"

(76mm)

60"

2

（）

387.1cm

2

60"

2

（）

387.1cm

2

7

6

English

12

1. Dryer MUST be exhausted outside (outdoors, not beneath the manufactured

home) using metal ducting that will not support combustion. Metal ducting must

be 4 inch (10.16 cm) in diameter with no obstructions. Rigid metal duct

is preferred.

2. If dryer is exhausted through the floor and area beneath the manufactured

home is enclosed, the exhaust system MUST terminate outside the enclosure

with the termination securely fastened to the mobile home structure.

3. When installing a gas dryer into a manufactured home, a provision must be

made for outside make up air. This provision is to be not less than twice the

area of the dryer exhaust outlet.

4. This dryer MUST be fastened to the floor using P/N 0030807988

Manufactured Home Installation Kit. Follow the instructions supplied with

the kit.

5. Refer to previous sections for other important venting requirements.

6. Installation must conform to current Manufactured Home Construction & Safety

Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when

such standard is not applicable, with American National Standard for Mobile

Homes. In Canada, the CSA Z240 is applicable.

MANUFACTURED (MOBILE) HOME INSTALLATION

DO DON’T

DON’T

DO

English

1. For your safety, please unplug the power cord before changing the drum light.

2. Open the dryer door, find the location of the drum light. Using a phillip head

screw driver remove the light cover (as shown below).

3. Remove the bulb by turning it counterclockwise. Replace the bulb with a

15-watt lamp only, then install the cover and tighten the screw.

4. Use your dryer after plugging it in the electrical socket.

CHANGING THE DRUM LIGHT

Screw

13

English

The following are specific requirements for

proper and safe electrical installation of your

dryer. Failure to follow these instructions can

create electrical shock and/or fire hazard.

WARNING

1.

This appliance must be properly grounded. Electrical shock can result if the

dryer is not properly grounded. Follow the instructions in this manual for

proper grounding.

2.

Do not use an extension cord with this dryer. Some extension cords are not

designed to withstand the amounts of electrical current this dryer utilizes and

can melt, creating electric shock and/or fire hazard. Locate the dryer within

reach of the receptacle for the length power cord to be purchased, allowing

some slack in the cord. Refer to the electrical requirements in this manual for

the proper power cord to be purchased.

3. A UL approved strain relief must be installed onto power cord. If the strain

relief is not attached, the cord can be pulled out of the dryer and can be cut

by any movement of the cord, resulting in electrical shock.

4. Do not use an aluminum wire receptacle with copper-wired power cord and

plug (or vice versa ). A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The proper wiring and receptacle

is a copper-wired power cord with a copper-wired receptacle.

NOTE: Dryers operating on 208 Volt power supply sill have longer drying times

than operation on 240 Volt power supply.

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

Improper connection of the equipment grounding conductor can

result in a risk of electrical shock. Check with a licensed

electrician if you are in doubt as to whether the appliance is

properly grounded.

1. Gas dryers are equipped with a factory installed three-prong 15 Amps ~120

Volts (grounding) plug for your protection against shock hazard and should be

plugged directly into a properly grounded three-prong receptacle. Do not cut

or remove the grounding prong from this plug.

ELECTRICAL INSTALLATION

ELECTRIC Dryer (CHDE/HDE5000AW and CHDE/HDE5300AW)

GAS Dryer (HDG5000AW and HDG5300AW)

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown,

grounding will reduce th risk of electric shock by providing a path of least

resistance for electric current. This appliance is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and grounded in accordance

with all local codes and ordinances. This appliance must be connected to a

grounded metal, permanent wiring system, or an equipment-grounding conductor

must be run with the circuit conductors and connected to the equipment-grounding

terminal or lead on the appliance.

14

English

3-Wire System (US models only)

1. Remove the screws securing the terminal block access cover and the strain

relief mounting bracket located on the back of the dryer’s upper corner.

2.

Install a U.L. approved strain relief into the power cord entry hole of the

mounting bracket. Finger tighten the nut only at this time.

3. Thread a U.L. Approved 30 Amp. Power cord, NEMA 10-30 Type SRDT,

through the strain relief.

4. Attach the power cord neutral (center wire) conductor to the brass colored

center terminal on the terminal block. Tighten the screw securely.

5. Attach the remaining two power cord outer conductors to the outer brass

colored terminals on the terminal block. Tighten both screws securely.

WARNING: Do not make a sharp bend or crimp wiring/conductor at

connections.

6. Reattach the strain relief mounting bracket to the back of the dryer with two

screws. Tighten screws securely.

7. Tighten the screws securing the cord restraint firmly against the power cord.

8. Tighten the strain relief nut securely so that the strain relief does not turn.

9. Reinstall the terminal block cover.

ELECTRICAL CONNECTIONS

ELECTRIC Dryer (HDE5000AW and HDE5300AW)

15

English

4-Wire Cord Connections (US Models Only)

1. Remove the screws securing the terminal block access cover and the strain

relief mounting bracket located on the back of the dryer upper corner.

2. Install a UL approved strain relief into the power cord entry hole of the

mounting bracket . Finger tighten the nut only at this time.

3. Remove the green neutral ground wire from the green ground screw located

above the terminal block.

Black 240V

White Neutral

Red 240V

Green Ground

Typical Conductor

Receptacle

Typical 4

Conductor Cord

ELECTRIC Dryer (HDE5000AW and HDE5300AW)

16

4. Thread a U.L. approved 30 Amp power cord. NEMA 14-30 type ST or SRDT

through the strain relief.

5. Attach the green power cord ground wire to the cabinet with green ground screw.

6. Attach the green wire conductors from the dryer and white (neutral) power cord

conductors to the brass-colored center terminal on the terminal block. Tighten the screw

securely.

7. Attach the red and black power cord conductors to the outer brass-colored terminals on

the terminal block.

Warning: Do not make a sharp bend or crimp the wiring /conductor at connections.

8. Tighten the screws securing the cord restraint firmly against the power cord.

9. Tighten the strain relief nut securely so that the strain relief does not turn.

10. Reinstall the terminal block cover.

NOTE: DO NOT connect the dryer to L.P. gas service without converting the

gas valve. An L.P. Conversion Kit must be installed by a qualified gas

technician.

1. Remove the shipping cap from gas pipe at the rear of the dryer.

2. Connect a 1/2 inch (1.27cm) I.D. semi-rigid or approved pipe from gas supply line to

the 3/8 inch (0.96cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8

inch (1.27cm to 0.96cm) reducer for a connection. Apply an approved thread sealer

that is resistant to the corrosive action of liquified gases on all pipe connections.

3. Open the shutoff valve in the gas supply line.

4. Test all connections by brushing on a soapy water solution. NEVER TEST FOR GAS

LEAKS WITH AN OPEN FLAME.

5. Connect the exhaust duct to the outside exhaust system. Use duct tape to seal all joints.

6. With the dryer in its final position, adjust one or more of the legs until the dryer is

resting solid on all four legs. Place a level on top of the dryer. THE DRYER MUST BE

LEVEL AND RESTING SOLID ON ALL FOUR LEGS.

7. Plug the power cord into a grounded outlet. NOTE: check to ensure power is OFF at

circuit breaker/fuse box before plugging the power cord into the outlet.

8. Turn on the power at the circuit breaker/fuse box.

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

Before operating the dryer, make sure the dryer area is clean and

free from combustible materials, gasoline, and other flammable

vapors. Also see that nothing (such as boxes, clothing, etc.) obstructs

the flow of combustion and ventilation air through the louvered

panel located on the rear of the dryer.

9. Run the dryer through a cycle check for proper operation.

NOTE: On gas dryers, before the burner will light, it is necessary for the gas line to be

bled of air. If the burner does not light within 45 seconds the first time the dryer is

turned on, the safety switch will shut the burner off. If this happens, turn the dryer to

“OFF” and wait 5 minutes before making another attempt to light.

NOTE: Follow instructons supplied with kit.

GAS CONNECTIONS

GAS Dryer (HDG5000AW and HDG5300AW)

English

17

A) Connect female 3/8” NPT elbow to gas

inlet on dryer. Then connect 3/8” flare

union adapter to female elbow.

IMPORTANT: To prevent the inlet from

twisting, please use a pipe

wrench to secure the dryer

gas inlet. Affix Teflon

®

tape or pipe compound to

adapter and gas inlet.

B) Attach the flexible metal gas line connector

to the adapter.

C) Make sure flexible gas line seal is secure.

Use two wrenches for the best possible

connection.

D) To check gas inlet pressure, attach 1/8”

NPT plugged tapping to dryer gas line shut-

off valve. Then connect flare union adapter

to plugged tapping. Affix Teflon® tape to

the threads of the adapter and plugged

tapping to ensure seal.

E) Use two adjustable wrenches to tighten

every connection.

IMPORTANT: Do not overtighten!

F) Open gas shut-off valve.

CONNECTING THE DRYER TO THE GAS SUPPLY

English

18

REPLACEMENT PARTS

Replacement parts and accessories for US and Canada can be purchased

through Haier America at 1-800-313-8495

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation. Check unit for proper operation after servicing.

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

Discard or destroy the carton and plastic bags after the

dryer is unpacked. Children should not be allowed to use

them to play with. Cartons covered in rugs, bedspreads or

plastic sheets can become an airtight chamber and cause

suffocation leading to death. Make all packing materials

inaccessible to children.

WARNING

ADVERTENCIA

ADVERTISSMENT

PRECAUCIÓN

PRECAUCIÓN PRECAUCIÓN

ATTENTION

CAUTION

The instructions in this manual and all other literature

included with this dryer can not cover every possible

condition and situation that may occur. Good safe practice

and caution must be applied when installing, operating,

and maintaining any appliance. If you are in doubt after

installing, call a certified electrician to install and wire the

dryer.

19

English

Page is loading ...

Haier CHDE 5000 AW User manual

Haier CHDE 5000 AW User manual

in other languages

Related papers

Other documents