TELRAN 560756 is a standalone access control system that provides secure, keyless entry for up to 2000 users. With its zinc-alloy housing, it is both vandal and explosion-proof, making it suitable for use in harsh environments. The device supports access via card, card + PIN, or PIN only, and can be easily installed on a standard 86x86mm mount box. Additional features include:
- Easy programming using the keypad or admin cards
- Supports pulse mode (door closes automatically after a set time) and toggle mode (door remains open until another valid user input is received)
- Built-in alarm output for tamper, lockout, and door ajar scenarios
TELRAN 560756 is a standalone access control system that provides secure, keyless entry for up to 2000 users. With its zinc-alloy housing, it is both vandal and explosion-proof, making it suitable for use in harsh environments. The device supports access via card, card + PIN, or PIN only, and can be easily installed on a standard 86x86mm mount box. Additional features include:
- Easy programming using the keypad or admin cards
- Supports pulse mode (door closes automatically after a set time) and toggle mode (door remains open until another valid user input is received)
- Built-in alarm output for tamper, lockout, and door ajar scenarios
123
456
7 8 9
0
*#
1
5678
234
U s er M anua l
10-24V DC
≤80mA
IP
2000
Card type
125KHz
≤2A
DC+
OPEN
GND
COM
NC
NO
+
-
IN T R O DU C T I O N
F ea tu r e s a nd B enef its
Waterproof, conforms to IP 54
54
S pe c if ic a tions
User Capacity
EM Card
Operating Temperature
Lock Output Load
Operating Humidity 10%～98%RH
Dimensions L110xW76xH22mm(Wide)
Unit Weight 436g
Shipping Weight 500g
P ac k in g L i s t
Add users
Delete users
S o u n d a nd L ight I n dic a tion
O per a tio n S ta tu s B u z z e r
Enter programming mode Red light shines
One beep
Stand by Red light bright
Orange light bright
In the programming mode
Open lock Green light bright
Operation failed
*
IN S TA L L AT IO N
S TA NDA L ON E M O D E
C onnec tion D iagra m
Attention: Install a 1N4004 or equivalent diode is needed when use
a common power supply, or the reader might be damaged.
(1N4004 is included in the packing).
(Admin Code) #
*
(Admin Code) #
*
(Admin Code) #
*
(Admin Code) #
*
(Admin Code) #
*
(Admin Code) #
*
(Admin Code) #
*
(Admin Code) #
*
*
*
*
*
*
*
*
*
*
*
E n te r a n d E x i t P r o g r a m m o d e
P ro g ram m in g S tep
P ro g ram m in g S tep
P ro g ram m in g S tep
P ro g ram m in g S tep
P ro g ram m in g S tep
P ro g ram m in g S tep
P ro g ram m in g S tep
P ro g ram m in g S tep
P ro g ram m in g S tep
K e y s tr oke C omb in a tio n
K e y s tr oke C omb in a tio n
K e y s tr oke C omb in a tio n
K e y s tr ok e C o mb in a tion
K e y s tr oke C omb in a tio n
K e y s tr ok e C omb in a tion
K e y s tr oke C omb in a tio n
K e y s tr oke C omb in a tio n
K e y s tr o k e C o mbina ti on
Enter Program Mode
Enter Program Mode
Enter Program Mode
Enter Program Mode
Enter Program Mode
Enter Program Mode
Enter Program Mode
Enter Program Mode
(Factory default is 777777)
Exit Program Mode
Exit Program Mode
Exit Program Mode
Exit Program Mode
Exit Program Mode
Exit Program Mode
Exit Program Mode
Exit Program Mode
Add Card User
Add Card: by Card
Add Card: by ID
number
1 (Read Card) #
W i r i n g
W ire C olo r F u nc ti on N o te s
Yellow OPEN
10-24V DC Power Input
Red DC+
Black GND Negative Pole
Green
Green
Green
NO Relay NO
Relay COM
COM
Brown
Brown
Brown
White
White
White
NC Relay NC
Enter the Programming Mode
Change the Admin Code
Add Card User 1 - R e a d C a rd - #
Add PIN User 1- U s er I D - # - P IN - #
(ID number:1-2000)
Delete User
2 - R e a d C a rd - #
(for Card User)
2 - U s e r I D -#
(for PIN User)
H ow t o r e le a s e t he d o o r
-40°C～+70°C,(-40°F～158°F)
123
456
7 8 9
0
*#
Admin Add Card Ad min Del ete Car d
Admin Cards
Diod e 1N400 4
(For r elay ci rcuit p rotec tion)
Wal l Anchors
80mm
60mm
40mm
Screw Driver
Self Tapping Screws
Mo d i fy A d m in C o de
Update Admin Code
0 (New Admin Code) #
(Repeat New Admin Code) #
(Admin Code is any 6 digits)
3 beeps
A dd/De l ete U s e r s b y A dmi n C ard
Step 1: Read Admin Add Card
Step 2: Read user cards
(Repeat step 2 for additional user cards)
Step 3: Read Admin Add Card again to end
Step 1: Read Admin Delete Card)
Step 2: Read user cards
(Repeat step 2 for additional user cards)
Step 3: Read Admin Delete Card again to end
A d d U s e r s b y K ey pa d ( ID N um be r : 1-2 00 0)
L E D
1 (Input ID number) #
(Read Card) #
Red shines
Orange bright
Orange bright
Read Range ≤6cm
P le a s e r e a d t h e u s e r m a nua l c a r ef ully b e fo r e i ns ta lla tion .
Zinc-alloy housing, anti-vandal, anti-explosion
User capacity: 2000
Length of PIN: 4 – 8 digits
Wide voltage input: DC 10-24V
Pulse Mode, Toggle Mode
Remove the back cover from the unit with screw.
Drill hole on the wall according to the back size of the machine
and fix the back cover to the wall. (or fix the back cover firmly to
the 86cm×86cm box)
Thread the cable through cable hole, connect related cable.
For the un-used cable please separate with insulating tape.
After wiring, install front casing to the back casing and fix well.
L ig ht
Exit Butt on
Yellow
Red
Black
10-24V DC
DC+
OPEN
GND
COM
NC
NO
Exit Butt on
Yellow
Red
Black
Power
Using Admin Cards to add delete card users
For safety, the Admin must change the Admin code.
L E D
L E D
L E D
L E D
L E D
L E D
Red shines
Red shines
Red shines
Red shines
Red shines
Red shines
Orange bright
Orange bright
Orange bright
Orange bright
Orange bright
Orange bright
Orange bright
Red bright
Red bright
Red bright
Red bright
Red bright
Red bright
Red bright
The length of the admin code is 6 digits, the admin should keep it in
mind.
S ta nd a lo ne A c c e s s C on tro l
This product is a contactless EM proximity card standalone access
control. It adopts zinc-alloy case, anti-vandal and anti-explosion,
2,000 user capacity and supporting access by card, card + PIN,
card or PIN. It can be installed on 86x86mm mount box.
Supporting block enrollment with cards sequentially numbered
Can be installed on 86mm×86mm box, very easy to install
Admin can add/delete admin cards,
making add/delete cards rapidly.
Operating Voltage
Working Current
Weatherproof
Card Frequency
Connect to Exit button and the
Exit button is connected to GND
Power off, press exit button, power on, release it until hear two
beeps. Swiping two cards, the first card is “Admin Add Card”, the
second card is “Admin Delete Card”, then the device will be in
standby mode. Resets to factory default setting and adding admin
cards are successful.
If you don't need to add admin cards: Power off, press exit button,
power on, release it until hear two beeps, and the orange LED turn
on. Waiting for ten seconds, there is a beep and it will be in standby
mode. Resets to factory default setting is successful.
Reset to factory default, the users' information won't be deleted.
S pec ia l P o we r S u pp ly f o r a c c e s s c o n tr o l s y s te m
C omm on p ow er s u pp ly
O R
O R
O R
O R
O R
O R
O R
Add proximity cards
sequentially numbered
8 (ID number) # (8/10
digits card number) #
(The number of cards)#
Add PIN users 1 (ID Number) #
(4-8 digits PIN)
N o te : 1. When swiping cards to add users, the user ID will be added
in automatically, and ID number will be from small to big,
ranged from 1 – 2000.
in automatically. This pin cannot used to open door. If you
want to open door by card + PIN, you should first change the
old PIN 1234, method referring to Change PIN.
2.When adding card users, an attached PIN 1234 will be added
3. Before add the proximity cards sequentially numbered,
the ID number should be sequential and empty.
Del ete U s e rs b y K ey pa d
Delete Card User-Common
Delete Card - By Card
Delete Card -
By ID number
2 (Input ID number) #
2 (Read Card) #
Delete All User 2 0000 #
Toggle Mode 3 0 #
3 (1-99) #
A c c es s M ode S e ttin g
Open door by card 4 0 #
Open door by card + PIN 4 1 #
Open door by card or PIN 4 2 # (Factory default)
A l arm O u tpu t T ime S e tting
Set alarm time 6(1-3) #
N o te : 1. Factory default is 1 minute.
S e t S a fe M ode
7 0 # (Factory default)
7 1 #
Alarm output Mode 7 2 #
U s er s S e ttin g
C ha ng e P IN
Change PIN which
attached to card users
(Read Card) (old PIN) # (New PIN) #
(Repeat New PIN) #
Change independent
PIN
(ID number) # (old PIN) # (New PIN) #
(Repeat New PIN) #
H ow t o r e le a s e t he d o o r
Open door by card
Open door by User PIN
Open door by user card + PIN
(Read Card)
(Users PIN) #
(Read Card) (Users PIN) #
Q u ic k S ta r t a nd O p e r a ti o n
Q u ic k S e tti ngs
Then you can do the
programming
(Factory default is 777777)
(New Code: any 6 digits)
Exit from the Programming Mode
*- A d min C o de - #
0 - N e w C o de - # - R e pea t
the N ew C o d e - #
(Cards can be added in
continuously)
Open door by card
Open door by User PIN
Open door by user card + PIN
(Read Card)
(Users PIN) #
(Read Card) (Users PIN) #
F ac tory D efa u lt s e ttin gs a n d a d d a d min c a r ds
Lockout Mode
P ul s e M ode a n d T ogg le M o de S e tting
Pulse Mode
N ote : 1. Factory default is P u ls e M od e and the access time is 5
seconds. When set the access time to “0”, the device will be
in Toggle Mode.
2. P ul s e M ode : The door will be closed automatically after
opening the door for a while.
3. To g gl e M ode : Under this mode, after opening the door, the
door won't be closed automatically until next valid user input.
That is to say, whether open or close the door, you must
swipe valid card or input valid PIN.
2. Alarm output time includes: the alarm time of anti-vandal,
safe mode and closing reminder.
3. Swipe valid card or Input valid PIN can remove the alarm.
Normal Mode
N ote : L oc k out M od e: If swipe card/input PIN with invalid users for
10 times in 1 minute, the device will be lockout for 10 minutes.
When the device repowered, the lockout will be canceled.
A l arm O u tp u t M ode : If swipe card/input PIN with invalid
users for 10 times in 1 minute, the buzzer built-in will be
activated.
N o te : The PIN can be changed to any one 4-8 digits, but cannot
be ‘1234’, and the PIN attached to the card is only used for
card + PIN access mode.
-
1
TELRAN 560756 is a standalone access control system that provides secure, keyless entry for up to 2000 users. With its zinc-alloy housing, it is both vandal and explosion-proof, making it suitable for use in harsh environments. The device supports access via card, card + PIN, or PIN only, and can be easily installed on a standard 86x86mm mount box. Additional features include:
- Easy programming using the keypad or admin cards
- Supports pulse mode (door closes automatically after a set time) and toggle mode (door remains open until another valid user input is received)
- Built-in alarm output for tamper, lockout, and door ajar scenarios
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Haworth 7021-6710c Operating instructions
-
Haworth 7021-6711d Operating instructions
-
Haworth 7029-9608b Operating instructions
-
DIGITALas AD7 User manual
-
Dioche A7 Stand Alone Access Control and Reader User manual
-
Haworth e100-4400a Operating instructions
-
Anviz M3 Quick start guide
-
Sebury W4 User manual
-
Dolphin DOLCSAW1000H User manual
-
QNAP TS-1079 PRO User manual
