2. Disnep
  3. CW-10368
CW-10368

Disnep CW-10368 Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Disnep CW-10368 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
W x 1
(25911)
This Package Contains
3/3/22 V1
STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House
A x 1
(43166) B x 1
(43175) D x 1
(43193)
C x 1
(43184)
L x 1
(43263)
K x 1
(43254)
E x 2
(43209)
F x 1
(43218) H x 1
(43236)
J x 1
(43245)
Q x 1
(43306)
R x 1
(43315)
P x 1
(43290)
S x 1
(43324) T x 1
(43333) U x 1
(43342) V x 1
(43351)
M x 1
(43272) N x 1
(43281)
G x 3
(43227)
X x 14
(23047)
CW-10368
Page size: 8.5” x 11” ( Sheet 1 Front Side )
J
H
H
K
L
X
Step 3
Attach
Sides (L&K)
to
Cockpit (H)
by inserting tabs into slots as
shown below. Match the numbers on the tabs for the correct
orientation.
Step 4
Reinforce connections by placing Clear Stickers (X) over the tabs and
slots of
Lower Panels
as shown
Step 2
Pre-fold and roll
Cockpit (H)
as shown below. Insert tab into slot.
Step 1
Fold
Strut (J)
as shown below. Lock tabs into slots.
CW-10368STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (2/6)
Page size: 8.5” x 11” (Sheet 1 Back Side )
J
E
E
E
X
Outside Inside
Back View Front View
THIS IS THE
FRONT
Top View
Step 7
Attach
Wings
to
Cockpit
as shown below. Arrange the panels
according to the reference below
Step 8
Fold tabs and insert into slots as shown below. Repeat on both sides.
8.1 Line up tab with right exterior
slot.
8.2 Push completely through.
8.3 Wrap front and insert tab into
middle slot.
8.4 Push middle seam to lock in
place. Reinforce connections by
placing Clear Stickers (X) over
the tabs
Step 6
Fold
Wings (E)
as shown below.
Step 5
Insert
Strut (J)
through completed
Cockpit
as shown below.
CW-10368STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (3/6)
Top
Front
Page size: 8.5” x 11” ( Sheet 2 Front Side )
G
G
G
F
D
C
Step 11
Lock roof in place by inserting tabs into smaller slot as shown below.
11.1 Line up tab with
large slot.
11.2 Push completely
through.
11.3 Wrap front and
insert tab into small slot.
11.4 Push to lock in
place.
Step 12
Fold
Side Walls (C & D)
of upper panels as shown below.
Step 10
Wrap around the side of
Braces (G)
and insert tabs into larger slots
on the other side.
Step 9
Attach
Roof (F)
to
Braces (G)
. Fold tabs and insert into larger slots
as shown below.
CW-10368STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (4/6)
Page size: 8.5” x 11” ( Sheet 2 Back Side )
A
B
Step 15
Lock sides in place by inserting tabs into smaller slot as shown
below.
Match tab graphics
with front and back.
Step 16
Attach
Assembled Ship
to roof by inserting tabs into slots as shown
below.
Step 14
Line up
Front Panel (A)
and
Back Panel (B)
with
Completed
Panels
. With the graphics on the tabs lining up, fold tabs and insert
into larger slots.
Step 13
Attach
Completed Roof
to side walls by inserting
Braces
into slots
of
Walls
. Push down to lock fully in place.
CW-10368STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (5/6)
Correct view
Incorrect view
Page size: 8.5” x 11” ( Sheet 3 Front Side )
WN
Q
P
T
U
V
S
R
M
Last Step
Remove protective film from double-sided tape of Small
Characters (P, Q, R, S, T, U & V)
attach stickers anywhere on the
house.
NOTICE: THIS SHIP IS NOT A STEP.
DO NOT ALLOW YOUR CAT TO
CLIMB ON TOP OF THE ROOF. IT IS
NOT INTENDED TO HOLD THE
WEIGHT OF A CAT.
Completed Item
Step 18
Remove protective film from double-sided tape of Side
Characters (N & M)
attach stickers anywhere on the house.
Step 17
Remove protective film from double-sided tape of Corrugate Board
(W). Slide Completed Panels down over the sides until it rests
over (W) as shown. Press to attach the board to the front and back
panels.
CW-10368STAR WARS™ Holiday TIE FIGHTER™ Gingerbread Cardboard Cat House (6/6)
Double-sided
tape
Page size: 8.5” x 11” ( Sheet 3 Back Side )
/