2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. Symmons
  6. IM600
IM600

Symmons IM600, IM600A, IM600AP1, IM600AP2, IM600P1, IM600P2 User manual

  • Hello! I'm your chat assistant, and I've reviewed the Symmons IceMate Valve Operation & Maintenance Manual for model IM600. This manual details the installation, features and maintenance requirements for the Ice Maker Valve. I'm here to answer any specific questions you might have about the valve or its installation process based on the information from the included document.
  • What are the available sizes for water hammer arrestor?
    What are the PEX connection options?
    What is the inlet size of the valve?
IceMate™
Model Numbers Feature Highlights
IM600
IceMateTM Valve
Operation & Maintenance Manual
☐IM600 IceMateTM Supply Box with Valve • Installation straps for 16" O.C. stud mounting or direct-
to-stud mounting.
• Ice Maker Valve.
• 1/2-14 NPSM with 1/2" Sweat Inlets 1/4" Outlet.
• Valve can be installed as bottom or top supply.
• Accommodates 1 layer of 1/2" drywall up to 2 layers of
5/8" drywall.
• Mounting straps.
Compliance
- ASME A112.18.1/CSA B125.1
- NSF 61.9, NSF 372
- ASSE 1010 (IM600A only)
Options/Modifications
☐AWater Hammer Arrestor Size AA
☐P1 Crimp PEX
☐P2 Cold Expansion PEX
Note: Append appropriate -sux to model number.
Dimensions
Measurements
A7", 178 mm
B6-5/8", 168 mm
C17-1/2", 445 mm
DMin. 1/2", 13 mm
Max. 1-1/4", 32 mm
E2-7/8", 72 mm
C
D
E
A
B
c
Limited Lifetime - to the original end
purchaser in consumer/residential
installations.
10 Years - for commercial/industrial
installations. Refer to
www.symmons.com/warranty for
complete warranty information.
Warranty
Note: Dimensions subject to change without notice.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2021 Symmons Industries, Inc. ■ symmons.com ■ [email protected]om ■ ZV-3467 REV A ■ 031622
Installation
Section A: (Steps 1-7)
1. Slide straps in mounting tabs
2. Attach strap to studs with user provided screws
3. Insert provided screws through tabs to secure box in
place
Section B: (Step 4)
4. Knockout inside hole of supply box for water supply
5. Secure valve to box with supplied nut
6. Connect supplies to valves with either:
a. Sweat connect
b. P1 Option - Crimp PEX or
P2 Option - Cold Expansion PEX
7. Check for leaks
Section C (Steps 8 & 9)
8. Complete finish wall
9. Press on covers
a. If finish wall is 1/2’’ thick, break tabs from cover
o
b. If 2 layers of 5/8” drywall leave tabs on
Section D (Step 10)
Direct Stud Installation:
10. Mount box on adjacent side of wall stud with
provided tabs
Section E (Step 11)
Surface Mount Installation:
11. Drill holes out of box and use user provided screws
to attach to wall
1
3
4
56
2
9
10
11
Section A
Section C
Section B
Section D Section E
4
/