Vivo STAND-V101SV Assembly Instructions

Category
Flat panel desk mounts
Type
Assembly Instructions
Silver Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101sv
SKU: STAND-V101SV
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
TOOLS NEEDED
2.2-19.8lbs
(1-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Arm
B (x1)
Pole
E (x1)
VESA Plate
F (x1)
Clamp Brace
G (x1)
Clamp
H (x1)
Clamp Cover
I (x1)
Grommet
Bolt
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer
C (x1)
Base
D (x1)
Cable Clip
J (x1)
Grommet
Plate
K (x1)
Support Plate
L (x1)
Lock Washer
M (x1)
Nut
N (x4)
Pad
O (x1)
4mm Allen
Wrench
P (x1)
6mm Allen
Wrench
Q (x1)
Wrench
R (x2)
M6x10
S (x3)
M6x12
T (x3)
M6x16
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Mount pole (B) to base (C) using M6x16
bolts (T) and tighten with the 4mm Allen
wrench (O). Attach clamp brace (F) to
base using M6x12 bolts (S) and tighten
with the 4mm Allen wrench (O). Apply
adhesive pads (N) to corners of base.
Attach clamp (G) to upper or lower
position on clamp brace using M6x10
bolts (R) and tighten with the 4mm Allen
wrench (O). Attach the clamp cover (H)
to the back of the clamp brace, then place
the base on the edge of the desktop and
tighten the knob to secure.
OPTION B: Grommet Base Installation
Mount pole (B) to base (C) using M6x16 bolts
(T) and tighten with the 4mm Allen wrench
(O). Insert grommet bolt (I) down through the
square hole in grommet plate (J), then attach
grommet plate to base using M6x12 bolts (S)
and tighten with the 4mm Allen wrench (O).
Apply adhesive pads (N) to corners of base.
If a grommet hole is not present in the desktop,
drill a hole using a 3/8” (10mm) bit at the
desired location. Place base on desktop,
making sure grommet bolt fits down through
hole, and secure using support plate (K), lock
washer (L) and nut (M), and tighten with the
wrench (Q).
4
STEP 2
Slide cable clip (D) and arm (A) down onto pole. Secure arm using the 6mm Allen wrench (P).
STEP 3
Install the VESA plate (E) to monitor using M4x12 bolts (M-A) or M5x12 bolts (M-B)
with washers (M-C), making sure the arrow in back is pointing up.
5
STEP 4
Pull back the release lever on the support bracket, then place the monitor
with VESA plate into the support.
STEP 5
If needed, adjust gas spring to support the monitor using the 6mm Allen wrench (P). Turn the screw in
back clockwise to decrease support, and counter-clockwise to increase. Adjust the tilt joint to tighten
or loosen tilt support.
6
STEP 6
Remove upper cable cover by spreading the sides and pulling down. Slide cable cover on lower arm
forward to remove.
STEP 7
Organize cables, then reinstall cable covers to arms.
7
Adjust as Desired
LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Vivo STAND-V101SV Assembly Instructions

Category
Flat panel desk mounts
Type
Assembly Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI