Groupe Brandt DTG303XA1 Owner's manual

Brand: Groupe Brandt

Model: DTG303XA1

Category: Hobs

Type: Owner's manual

Hob operating guide

99637131_GB_A.qxd 13/06/2005 10:04 Page 1

In this Manual,

displays safety instructions

displays tips and hints

List of contents

Using your hob in complete safety 4

What your hob looks like? 5

Installing your hob in all simplicity 6

Fitting recommendations 6-8

Electrical connections 9

Gas connections 9

Changing the type of gas supply 10-12

Using your hob in all simplicity 13

Before leaving 13

How to use your gas burners 13

How to use the timer ? 14

Which pans are best adapted for use

on the gas burner? 15

How to look after your hob? 16

Minor troubleshooting 17

Gas-cooking guide 18

A few hints 19

99637131_GB_A.qxd 13/06/2005 10:04 Page 2

Dear Customer,

You have just acquired a DE DIETRICH glass-top hob, for which

we thank you. DE DIETRICH has designed this equipment to

meet all your requirements in terms of quality, a esthetics and

performance.

Made of high quality material, DE DIETRICH glass-top hobs are

a symbol of elegance. Their thermocouple gives you total safety

and their glass-top makes cleaning extremely easy.

DE DIETRICH offers its latest and best know-how to improve

your quality of life and respect our environment.

We thank you for your confidence and invite you to read this

guide very carefully. It will enable you to install and use your new

glass-top as well as possible and get to know all the possibilites it

makes available to you.

DE DIETRICH.

Editorial

99637131_GB_A.qxd 13/06/2005 10:04 Page 3

Your hob in complete safety

Using your hob in complete safety

YOUR HOB IS DELIVERED PRE-SET FOR USE WITH NATURAL GAS.

SEE TO KNOW THE GAS CARACTERISTICS.

- We have designed your hob for

private domestic use.

- With a view to the constant

improvement of our products, we

reserve the right to make any

changes in their technical, functional

or aesthetic characteristics as a result

of technical evolution.

- These hobs are designed exclusively

for the cooking of drinks and food-

stuffs. These products do not contain

any asbestos-based component parts.

- You must always keep an eye on

your cooking.

- Please read the instructions before

installing and using this appliance.

- Should a crack appear on the

glass, disconnect your

appliance immediately and

contact your After-Sales

Service.

- Never leave any

CLEANING OR

INFLAMMABLE

products in the

cupboard or drawer beneath your

hob (aerosols or other pressurised

cans, papers, recipe books, etc.).

- Using a gas-powered hob produces

both heat and humidity in the room

where it is used. Make sure your

kitchen is well ventilated.

- Disconnect your hob from both

electrical and gas supplies before

carrying out any maintenance

operations.

- For safety reasons, do not forget to

close the main gas valve for built in

gas lines or the valve on the top of

your butane/propane gas cylinder.

- If a knob is difficult to turn,

DO NOT

FORCE IT

. Call up your installer.

- Where this appliance is installed in

marine craft or in caravans, it shall

not be used as a space heater.

- Do not spray aerosols in the vicinity

of this appliance while it is in

operation.

- Young children should be supervised

to ensure that they do not play with

the appliance.

- This appliance is not intended for

use by young children or infirm

persons without supervision.

- If you use a drawer under your hob,

we advise you not to keep any

objects in it that are liable to suffer

from heat (plastic, paper, aerosols,

etc.).

- If you plug in any electrical

appliance near the hob, make sure

that its power cable is not in contact

with any source of heat.

Do not place anything,

e.g. flame tamer,

asbestos mat, between

pan and pan support as

serious damage to the

appliance may result.

Do not remove the pan

support and enclose the

burner with a wok

stand as this

willconcentrate and

deflect heat onto the

hotplate.

Do not use large pots

or heavy weights which

can bend the pan

support or deflect flame

onto the hotplate.

99637131_GB_A.qxd 13/06/2005 10:04 Page 4

What your hob looks like?

60 cm model with 4 gas burners

30 cm model with 2 gas burners

Burner

(A) Semi Fast burner

(B) Fast burner

(D) Wok burner

(E) Auxiliary burner

Nominal gas

consumption (NG)

5.4MJ/h

8.0MJ/h

11.0MJ/h

12.0MJ/h

3.4MJ/h

99637131_GB_A.qxd 13/06/2005 10:04 Page 5

This appliance shall be installed by

authorised personnel and in

accordance with the manufacturer’s

installation instruction local gas fitting

regulations, municipal building codes,

electrical wiring regulations, AS

5601/AG 601 - Gas Installations and

any other staturory regulations.

DATA LABEL

The Data Label is located on the

underside of the appliance. The

informations on the data label are

duplicated in this user’s manual. This

appliance is suitable for Natural Gas

and Universal LPG; ensure that the

available gas supply matches the

Data Label.

Installing your hob in all simplicity

VENTILATION

Ventilation must be in accordance

with AS5601/AG 601 - Gas

installations. In general, the

appliance should have adequate

ventilation for complete combustion

of gas, proper flueing and to maintain

temperature of immediate

surroundings within safe limits.

Fitting recommendations

30 cm 60 cm

30 cm

60 cm

Cutout

Model

Width

26,5 cm 56 cm

Depth

49 cm 49 cm

Height

Depending on

cupboard

Outside

dimensions above

the work surface

31 cm 65 cm 51 cm 51,8 cm 5 cm 6 cm

Outside

dimensions under

work surface

26 cm 55 cm 47 cm 47 cm 5,1 cm 5,1cm

99637131_GB_A.qxd 13/06/2005 10:04 Page 6

Installing your hob in all simplicity

The hob must be built into the worktop of

a support cupboard. This worktop must be

at least 3 cm thick and heat-resistant or el-

se coated with a heat resistant material.

Any adjoining wall surface situated within

200mm from the edge of any hob burner

must be a suitable non-combustible mate-

rial for a height of 150mm for the entire

length of the hob. Any combustible

construction above the hotplate must be at

least 600mm above the top of the burner

and no construction shall be within 450mm

above the top of the burner. A minimum

depth of 60mm from the top of the work-

top surface must be provided for the ap-

pliance.

A tall cupboard or partition too close to the

hob would hinder free movement of kit-

chen ustensils.

To make sure that nothing can get bet-

ween the frame and the worktop,

before you install the unit, stick the foam

seal around the outside of the hob, as

follows:

1- Remove the pan support grates, the

burner caps and heads after checking their

position.

2- Turn the hob over and place it gently

over the opening in the worktop paying at-

tention not to damage the control knobs

and lighters.

3- Stick the foam seal delivered with your

appliance around the outside of your

hob. This seal prevents any foreign bodies

or liquids from getting under the hob.

Fitting recommendations (cont'd)

49 cm

3 cm mini

30 cm mini

56 cm / 26,5 cm

5,3 cm mini

70 cm mini

Seal

99637131_GB_A.qxd 13/06/2005 10:04 Page 7

Installing your hob in all simplicity

Fitting recommendations (cont'd)

If a horizontal partition is put under the

hob, it must be placed between 10 and 15

cm from the bottom of the worktop. In any

case, do not keep any sprays or pressuri-

zed containers in the compartment

which could be just under the hob.

Place the hob in position in the cutout on

the worktop, pulling it forward as far as

possible.

- Put the burners, caps and pan grates in

place.

- Connect the hob power supply cable to

the electrical installation of the kitchen.

(See “Electrical connections” for the

hob).

- Connect to your gas supply (see “How

to connect the hob to the mains gas

supply” or “How to connect the hob to

butane or propane gas).

If you want, you can fix the hob on its four

corners, using the four lugs and screws

provided. (See diagram).

Only use the holes provided.

Stops screwing when the lug starts to

bend.

Do not use a power screwdriver.

Fixing lugs

Worktop

Fixing holes

4 gas burner hob 2 gas burner hob

99637131_GB_A.qxd 13/06/2005 10:04 Page 8

Installing your hob in all simplicity

These hobs are supplied with a

plug & cord, simply plug into a 3 pin

household socket outlet which is pro-

perly earthed. In order to avoid ha-

zard, any electrical work performed on

this equipment or its associated wring,

should only be done by persons au-

thorised by the supplier or similarly

qualified persons.

The socket outlet for this hotplate

shall be installed near the hotplate

and shall be easily accessible.

Electrical connections

● All-gas hobs

The protective conductor is

connected to the earth

connection on the hob

and therefore must also be

connected to an external earth

connection .

If this cable is damaged, have it re-

placed by your authorised service

agent as special tooling is required

to connect it correctly.

Gas connections

The Gas connection is male 1/2” BSP

and is situated at the right hand rear

of the appliance, 50mm from the right

side and rear of the cooktop and

30mm below the benchtop. This ap-

pliance is suitable for connection with

rigid pipe only. When connecting to

Natural Gas, ensure the gas regulator

supplied with the hotplate is connec-

ted as close as practical to the gas in-

let. If connecting to Universal LPG, en-

sure the test point assembly supplied

with the hotplate is connected as clo-

se as possible to the gas inlet.

Commissioning test point

pressure (NG)

Appliance is factory set to 1.0 kPa

test point pressure. Check the test

point pressure with the Extra Fast

Burner operating at maximum flame

for the 2 burner model and the Wok

burner operating at maximum flame

for the 4 burner model.

Test point pressure (U-LPG)

If converting to Universal LPG, check

that the test point pressure is

2.75kPa.

Make sure that all gas

pipes and connections are

gas sound after installa-

tion by using soapy-water.

See the gas caracteristics table.

99637131_GB_A.qxd 13/06/2005 10:04 Page 9

Installing your hob in all simplicity

Changing the type of gas supply

Spanner

Line

Fig. 3

Fig. 2

Cover

Head

Dish

Grill

Hearth plate

Fig. 1

•

Replace these with the injectors

supplied in the wallet, in accordance

with the gas rating table at the end of

the chapter; to do this:

➪ Screw in the injectors by hand until

they are tight.

➪ Put the spanner well onto the injec-

tor.

➪ With a pencil draw a line on the

hearth plate as indicated (fig. 2).

➪ Turn the spanner clockwise until

the line appears on the other side

(fig. 3). Warning! Do not go

beyond this limit as you are liable

to cause damage.

When carrying out this operation, you

should successively:

➊

Adapt the gas connection

❷

Change the injectors

❸

Adjust the retarder on the taps

➊

ADAPT THE HOB CONNECTION to the new

gas adjustment. Refer to the paragraph

“Gas connections”.

❷

CHANGE THE INJECTORS in the following

way:

•

Remove the supports, and all the bur-

ner caps and heads.

•

Using the spanner supplied, unscrew

the injectors at the bottom of each dish

and remove them (fig 1).

● Preliminary remarks

Your hob is delivered regulated for

Natural Gas.

The injectors for adapting the hob for use

with Universal LPG are in the wallet contai-

ning the instructions, together with the

adaptor and the sealing washer.

Every time you change your gas supply,

stick the gas label supplied in the wallet

corresponding to the new type of gas.

When converting from Natural Gas to Uni-

versal LPG ensure that the NG regulator is

removed and replaced with the test Point

Assembly. A gas regulator suitable for a

supply pressure of 2.75kPa should be part

of the gas tank supply. Check that the test

point pressure is 2.75kPa.

99637131_GB_A.qxd 13/06/2005 10:04 Page 10

Installing your hob in all simplicity

Changing the type of gas supply (cont'd)

❸

ADJUST THE RETARDER ON THE TAPS lo-

cated under the knobs. Proceed as

follows:

A - Changing from Natural

Gas to Universal LPG

•

Work on one tap at a time.

•

Remove the control knobs by pulling

them upwards.

•

Using a small screwdriver, screw fully

the brass adjustment screw (yellow) (Fig.

4) clockwise

•

Check the position of the knobs before

putting them back in place. Make sure the

knobs are pushed down as far as possible.

•

Put all the burners, covers and grills

back in position.

B - Changing from Univer-

sal LPG to Natural Gas

•

Work on one tap at a time.

- Light up the burner at maximum heat.

- remove the corresponding control

knob.

- Using the small screwdriver unscrew

the brass adjustment screw (yellow) tur-

ning it round twice, anti-clockwise

(Fig. 4).

- Put the control knob back in place and

turn to minimum flame.

- Remove the knob again then turn the

adjustment screw clockwise as low as

possible without extinguishing the flames.

- Put back the sealing ring and control

knob then turn it several times from maxi-

mum position to minimum position : the

flame must not be extinguished.

Otherwise, readjust it by slightly screwing

or unscrewing the adjustment screw so

that a stable flame is obtained when the

knob is turned from maximum to minimum

position.

Adjustment

screw

Fig. 4

Tap axis

Adjustment

screw

Fig. 4

Tap axis

99637131_GB_A.qxd 13/06/2005 10:04 Page 11

Gas Type

Test Point pressure (kPa)

Wok burner

Indicator marked on injector

Specified injector size (mm)

Nominal gas consumption (MJ/h)

Extra fast burner

Indicator marked on injector

Specified injector size (mm)

Nominal gas consumption (MJ/h)

Fast burner

Indicator marked on injector

Specified injector size (mm)

Nominal gas consumption (MJ/h)

Semi-fast burner

Indicator marked on injector

Specified injector size (mm)

Nominal gas consumption (MJ/h)

Auxiliary burner

Indicator marked on injector

Specified injector size (mm)

Nominal gas consumption (MJ/h)

Natural Gas U-LPG

1.00 2.75

149 95

1.58 0.98

12.0 11.5

158 88

1.57 0.88

11.0 10.0

133 78

1.34 0.78

8.0 7.6

107 62

1.07 0.62

5.4 4.9

80 45

0.83 0.45

3.4 2.3

60 cm model with 4 gas burners

Total gas consumption (MJ/h)

30 cm model with 2 gas burners

Total gas consumption (MJ/h)

28.8 26.3

16.4 14.9

Installing your hob in all simplicity

Changing the type of gas supply (cont'd)

● Gas rating

107 133

149 80

62 78

95 45

60 cm model with 4 gas burners

This table shows the position of the injectors on your hob depending on the type of gas you

use. The number is marked on each injector.

Universal LPG

MARK ON THE INJECTORS

158

107

30 cm model with 2 gas burners

Universal LPG

Natural gas

1.00

Natural gas

1.00

99637131_GB_A.qxd 13/06/2005 10:04 Page 12

To set off the safety device, keep the

knob pressed completely down for a

few seconds after the flame has lit

up.

•

Each burner is controlled by a tap fitted

with a safety device, which cuts the gas

off automatically, if ever the flame goes

out by accident (overflowing, drafts, etc.).

•

The safety device for the burners is in

the form of a metal rod (a thermocouple)

beside to the flame.

•

Your hob is fitted with an automatic

lighting system integrated into the control

knobs.

•

Should there be an electricity cut, you

can always light a burner using a match

and by pressing down on the control knob

at the same time.

Using your hob in all simplicity

•

Choose the burner

you need using the sym-

bols at the side of each

control knob; (E.g. back

right-hand burner).

For lighting a burner:

•

Press down on the

control knob and turn it

anti-clockwise to maxi-

mum flame height. The

lighter for the burner will

spark as long as you

keep the control knob

pressed down.

•

Set the flame height

as required.

The gas tap is closed when

in the “” position.

How to use your gas burners?

- If ever your flame goes out, relight it as per normal procedure.

Sparker

Burner

holder

Natural gas

injector

Burner cover

Thermocouple

(Gas safety device)

Burner

head

- The flames on the burner are smaller near the grate supports to avoid any damage being

done to the enamel.

- The noise made by certain burners is related to their power and burning gas; this does not

harm the quality of cooking in any way.

Check all connections for gas leaks with soap and water. DO NOT use a naked flame for de-

tecting leaks. Ignite all burners to ensure correct operation of gas valves, burnes and ignition.

Turn gas taps to low flame position and observe stability of the flame. When satisfied with the

hotplate, please instruct the user on the correct method of operation. In case the appliance

fails to operate correctly after all checks have been carried out, refer to the authorised service

provider in your area.

Before leaving

99637131_GB_A.qxd 13/06/2005 10:04 Page 13

On models DTG303*/*, the back

right-hand burner is equipped

with a timer (maximum cooking ti-

me 99 minutes). It can, however,

be used independently.

•

Light the back right-hand burner

(see previous page).

•

Set it to the flame height you

require.

•

Press the or touch

controls on the ti-

mer.

As soon as you put your finger on

one of these two controls, the

timer starts and the cooking time

(in minutes) scrolls down on the

display.

•

Turn the back right-hand burner

control knob back to “



”.

•

To change the cooking time, you can

press the

or controls whenever

you wish.

•

To stop the timer during

cooking, put your finger on the

and touch controls at the

same time, until the timer display

goes out.

The burner will stay alight without

How to use the timer ? (Model with 4 rings and a double crown burner)

When cooking time has over, the gas supply to the burner is cut off

immediately and the burner goes out.

Should there be a power cut when the back right-hand burner is being

used with the timer, the timer cuts itself off when the power supply

comes back on.

Using your hob in all simplicity

99637131_GB_A.qxd 13/06/2005 10:04 Page 14

Using your hob in all simplicity

Which pans are best adapted for use on the gas burner ?

•

Recommended pan sizes:

Adjust the flames so that they do not

lick up the side of your pan.

Do not use a pan with a convex

or concave bottom.

Do not leave the gas on beneath an

empty pan.

Do not use pans whose handles may

partially cover control knobs.

Do not use heat regulators, toasters,

steel meat grills or stew-pots that

touch the glass-top.

Extra fast

burner

18 to 28 cm

Fry-ups

Bringing to the boil

Fast

burner

16 to 26 cm

Searing

Semi-fast

burner

14 to 22 cm

Sauces,

Reheating

Auxiliary

burner

12 to 16 cm

Simmering

RIGHT

WRONG

CONVEX

CONCAVE

The appliance should have adequate ventilation for complete combustion of

gas. Prolonged, intensive use of the hob may require extra ventilation by

opening a window or increasing the speed of the rangehood (a minimum air

input of 2m3/hour per kW of gas energy is required).

E.g. : for 60 cm hob with 4 gas-rings

Total power : 12.0 + 8.0 + 5.4 + 3.4 = 28.8 MJ/h

28.8 x 2

= 16 m

/h per hour minimum flow-rate.

99637131_GB_A.qxd 13/06/2005 10:04 Page 15

Looking after

sparkers and

injectors

Looking after

your glass top

- If ever the sparkers

get dirty, clean them

with a stiff non-

metallic brush.

-The gas injectors are

in the centre of each

burner in the form of

a "pot". Make sure not

to block them up partially when cleaning the

hob, as this will considerably reduce the

performance of your gas-rings.

If ever it is blocked use a safety pin to free it.

- Small hard-bristled

brush.

- Clean it with hot water, then wipe dry. Use

special ceramic glass cleaning products for

any persistent stains.

- Renovation product

available in the shops;

Looking after

the grills and

gas burners

- Use a non-abrasive cream for removing any

persistent stains. Then rinse with clean

water. Dry each burner element carefully

before re-lighting your hob.

- Non-abrasive cream

- Household sponge.

HOW TO PROCEED

ACCESSORIES TO

BE USED

Keeping your hob in good condition is easy if you clean it before it is completely

cold. Even so, never clean it when it is in use. Put all the electric and gas control

knobs at zero.

How to look after your hob?

- Should a crack appear on the glass-top, disconnect your applian-

ce immediately and contact your After-Sales Service.

- Servicing should be carried out only by authorised personnel.

- It is better to wash the parts of your hob by hand rather than in a dishwasher.

- Never use scouring pads for cleaning your hob.

thermocouple

Nut

Injector

Sparker

99637131_GB_A.qxd 13/06/2005 10:04 Page 16

You have doubts about whether your hob is working correctly .... ......

this does not

necessarily mean there is a breakdown. Nevertheless, check the following points

If your hob is fitted with a gas safety

device and the flames go out as soon

as you release the control knob.

In the low position the

flames go out or are

too high.

Flames are irregular.

- Avoid any severe drafts in the room.

- Check that the gas you are using corresponds to the injectors that

have been installed (See injector identification in the "Gas Rating"

chapter).

Remember that gas hobs are delivered preset for use with natural gas.

- Check that the burners and injectors are clean and assembled

correctly.

- Check you have enough gas in your gas cylinders.

The knobs get hot during cooking.

Use small pans on the burners next to the control knobs. Large pans

are to be put on the large burners furthest away from the knobs.

Put the pan in place with the burner in the middle. The pan should not

be above the control knobs.

Displayed on the timer “ ”

- Your appliance has a fault in it.

- Please contact the After-Sales Service.

WHAT SHOULD YOU DO?IF YOU REALIZE THAT

Lighting the burners:

There is no sparking when the

control knobs or buttons are pressed

down.

When you only press down one

control knob all the burners spark.

Sparking takes place but the burners

do not light up.

- Check the electrical connections on the hob.

- Check that the sparkers are clean.

- Check that the burners are clean and in position.

- If the hob is fixed to the worktop, make sure that the fixing clamps

have not been twisted.

- Check that the sealing rings have not come out of place.

This is normal. The lighter system is centralised, and all the burners

spark at the same time.

- Check that the gas inlet pipe has not been squashed.

- Check that the gas inlet pipe tube is less than 2m long.

- Check that the main gas tap is open.

- If you use gas tanks or cylinders check that they are not empty.

- If you have just installed your hob or changed a gas cylinder, keep

the control knob wide open for a few seconds so that the gas can get

through.

- Make sure the injector is not blocked up. if this is the case, clear it

with a safety pin.

- Light up your gas burner before putting a pan on it.

- Check that the gas you are using corresponds to the injectors that

have been installed (See injector identification in the "Gas Rating"

chapter).

- Push the control knob down completely and keep it under pressure

for a few seconds after the burner has lit.

- Check that the burner parts are in place.

- Check that the sealing rings under the control knobs have not come

out of place.

- Avoid any severe drafts in the room.

- Light the burner before putting your pan on it.

Minor troubleshooting

99637131_GB_A.qxd 13/06/2005 10:04 Page 17

Gas-cooking guide

DISHES TIME EXTRA- FAST SEMI- AUXILIARY

FAST FAST

SOUPS Broths 8-10 minutes X

Thick soups X

FISH Court-bouillon 8-10 minutes X

Grilled 8-10 minutes X

SAUCES Hollandaise, bearnaise XX

Bechamel, aurore 10 minutes XX

VEGETABLES Endives, Spinach X

Peas In Sauce 25-30 minutes XX

Provence Tomatoes 15-20 minutes XX

Fried Potatoes XX

Pasta X

MEAT Steack X

Blanquette, Osso-bucco 90 minutes X

Fried Escalope 10-12 minutes X

Tournedos (cast iron grill pan) 10 minutes X

FRYING Chips, Fritters X

DESERTS Rice Pudding 25 minutes XX

Stewed Fruits XX

Pancakes 3-4 minutes XX

Chocolate 3-4 minutes X

Custard 10 minutes X

99637131_GB_A.qxd 13/06/2005 10:04 Page 18

Lighting with gas

safety device

To start safety device, maintain the knob fully pressed after the

appearance of the flame.

In the case of a power cut, it is possible to light the burner by

bringing a lighted match close to the chosen burner whilst

pressing the corresponding knob.

Use of pans

Always use stable heat resistant pots and pans, with flat

bottoms, on gas stoves.

Tips

Reach each page of the guide closelyfor more detailed information.

As soon as water boils reduce the flame, you will thus limit

the risks of overflowing.

Place lids on pans: this is energy saving.

General maintenance

Clean your burners regularly : it is essential for keeping

them in good working order and guarantees a stable and

regular flame.

Do not forget the spark plugs. Dry each part of the burners

correctly before replacing them.

Finish the cleaning by wiping the glass top with kitchen roll

to remove any traces of water.

You will have pleasure in cooking by respecting some operating, cleaning and

maintenance rules.

A few hints

MEA

Phone 1300 553720

Fax : 1300 553719

99637131_GB_A.qxd 13/06/2005 10:04 Page 19

Distributed by MEA (A Divisions of Hagemeyer Brands Australia).

1. Subject to the "Statement of Standard

Warranty Conditions" this product is covered by

the following Warranty.

TWO (2) YEARS WARRANTY from date of

purchase, covering all parts and labour.

2. The appliance is warranted under normal

single family domestic installation and use, as set

out in the user manual, against manufacturing

defects for the Warranty periods shown above.

3. Should service be required under this

Warranty, the purchaser should contact an

approved DE DIETRICH Service Provider during

their normal business hours.

4. At no time does DE DIETRICH have liability for

any freight or transportation costs or for any

damage during transit or for any consequence of

failure of this appliance outside of the normal

service area, unless such limitation of liability is

prohibited by statute.

5. This Warranty excludes replacement of parts

required due to normal wear and tear including

light globes.

6. This Warranty only applies, provided the

appliance has been used in accordance with the

manufacturer's instructions and provided an

accident, misuse, neglect or abuse has not

damaged the appliance.

7. None of the above Warranties purport to

exclude, restrict or modify either the application

or the exercise of a right conferred by any

applicable Statute.

8. Please complete the details below, which

should be retained for future reference along

with your proof of purchase:

Date of Purchase: ......................................

Model No: ...................................................

Serial No: ....................................................

Notice to Victorian Customers from the Victorian

Plumbing Industry Commission.

This product must be installed by a licensed person as

required by the Victorian Building Act 1993.

Only a licensed person will give you a Compliance

Certificate, showing that the work complies with all the

relevant standards. Only a licensed person will have

insurance protecting their workmanship for 6 years.

Make sure you use a licensed person to install this

product and ask for your Compliance Certificate.

DDE DIETRICH

PRODUCT WARRANTY

Distributed by MEA (A Divisions of Hagemeyer Brands Australia).

1 The Warranty only applies provided that the

appliance has been used in accordance with the

manufacturer's instructions and provided that the

appliance has not been damaged by an accident,

misuse, neglect or abuse of any person other

than the manufacturer or MEA or from faulty

installation, mis-adjustment or tampering by

unauthorised persons.

2. When a service inspection reveals the alleged

fault or faults are caused by incorrect operation,

contrary to the instruction manual, and

otherwise the appliance is in good order and

working condition, the purchaser shall be liable

for a service fee charged by MEA or one of its'

Service Providers.

3. If the appliance is used in Commercial

Applications or for Rental purposes, a separate

warranty of Twelve (12) months covering all

parts with Three (3) months on the labour will

apply.

4. Subject to the provisions of any applicable

statute this Warranty applies to the original retail

purchaser only and is not transferable.

5. Subject to the provisions of any applicable

statute, at no time does MEA have liability for

freight, transport or travel costs outside normal

service areas.

6. This None of the above Warranties purport to

exclude, restrict or modify either the application

or the exercise of a right conferred by any

applicable statute.

7. Subject to any Warranties implied by statute,

at no time will MEA or its' Service Providers be

liable for any economic loss consequent upon the

failure of the appliance.

8. This Warranty is only valid for De Dietrich

major appliances imported and distributed by

MEA, purchased and used in Australia.

DSTATEMENT OF STANDARD

WARRANTY CONDITIONS

Appliance ref:

DTG303*/*

9963-7131 - 06/05

99637131_GB_A.qxd 13/06/2005 10:04 Page 20

Groupe Brandt DTG303XA1 Owner's manual

Brand: Groupe Brandt

Model: DTG303XA1

Category: Hobs

Type: Owner's manual

Download PDF

report

Groupe Brandt DTG303XA1 Owner's manual

Groupe Brandt DTG303XA1 Owner's manual

Related papers

Other documents