CMI 192-6435 Installation guide

CMI
Brand
CMI
Model
192-6435
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Model No. : 192-6434 Polished Chrome
192-6435 Brushed Nickel
192-6436 Oil-Rubbed Bronze
3 Hole Installation , 4" Center-Set
Revised 5/2/17
In the event that Freendo faucets are used in a Commercial Application, this warranty is limited for
a period of 5 years, unless otherwise specifically stated in the catalog and/or price book.
Aegean Two Handle Bathroom Faucet with
Brass Pop-up
repair. Compass Manufacturing International will, at its discretion, provide new or equivalent replacement
parts for any product that proves to be defective under normal usage and service.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Putty Plate
Body
20
Inlet
Aerator
No. Part Name
Deck Plate
Cartridge Locknut
Brazed Underbody
Allen Key
Spout
Cartridge(Hot Water)
Cartridge(Cold Water)
O-ring
Screw
Screwdriver
Flange
Locknut
Drain Body
Extend Rod
Horizontal Rod
Rod Guide Nut
Top Rubber Washer
Bottom Rubber Washer
Drain Stopper
Washer
Tailpiece
Rod Ball Plastic Gasket
21
22
23
24
25
26
27
28
29
30
31
32
33
34
21
22
23
24
25
26
27
28
30
31
29
32
33
34
Plumber's Putty
35
Lift Rod
Extend Rod Screw
35
Spring Clip
1
2
3
4
5
9
6
7
8
10
11
12
13
14
15
16
17
18
19
20
Handle
Screw
O-ring
O-ring
Flow Restricter
Washer
Plastic Locknut
36
36
Faucet Tailpiece
and/or Silicone
9
1
Warning:
The supply valve and supply lines are not included.
A. Faucet tailpiece B. Faucet tailpiece C. Faucet tailpiece
2. Remove the plastic locknut 19 and washer 18 from
faucet. Don't remove the putty plate 17 from faucet.
17
18
19
3. Position the faucet on the countertop with putty
plate 17 . Replace the washer 18 and plastic locknuts
19 on the faucet tailpiece 36 and tighten the plastic
locknuts 19 by hand.
36
17
18
19
Let both hot and cold water run for one minute.
This will help clean any debris that might clog
the system.
rod guide nut 31rod ball
plastic
gasket 30
drain
stopper
hole
drain
body 27
o-ring
sink
drain stopper 21
flange 22
align hole in
drain stopper
with guide rod
opening
(pointed toward
back wall)
flange 22
drain body 27
top rubber washer 23
sink base
locknut 26
washer 25
bottom
rubber
washer 24
tailpiece 28
faucet
body
extend rod 33
horizontal rod 29
A. Remove pop-up drain stopper 21.
and flange 22 with top rubber
washer 23 for pop-up assembly.
B. Insert drain body from underneath
of sink drain hole.Replace flange 22
and top rubber washer 23 back to
drain body 27.Tighten flange as far
as possible.
C. Slide bottom rubber washer 24
on drain body up against bottom
of sink. Tighten washer 25 and
locknut 26 firmly against base
for tight seal.
D. Remove tailpiece 28 from drain
body 27 ,add teflon tape, replace
tailpiece 28 .
A. Replace pop-up drain stopper 21
to drain body 27 with o-ring in
place, and align stopper hole
with guide rod opening.
A. Remove rod guide nut 31 and
rod ball plastic gasket 30 .
B. Insert horizontal rod 29 into
drain body 27 and through hole
in drain stopper 21 .
C. Replace rod guide nut 31 with
rod ball plastic gasket 30 and
tighten it.
horizontal rod 29
spring
clip 32
A. Insert lift rod 34 through hole on
faucet body. Connect horizontal
rod 29 to extend rod 33 using
spring clip 32 to hold and adjust.
B. Attach extend rod 33 with
lift rod 34 by inserting lift rod
through extend rod hole. Now
adjust lift rod 34 to correct height
and hand tighten extend rod
screw 35 .
extend rod
hole
extend rod
screw 35
lift rod 34
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

CMI 192-6435 Installation guide

CMI
Brand
CMI
Model
192-6435
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents