Novatto NSFC-CV002NA359ORB Installation guide

NSFC-CV002NA359ORB
Novatto
Brand
Novatto
Model
NSFC-CV002NA359ORB
Type
Installation guide
TROUBLESHOOTING TIPS
SoluonReasonIssue
Use silicone; ghten Umbrella drainDrain is loose
Make sure correct seal is used and
is below bevel
Umbrella drain is too high;
wrong seal used
Tighten the fastener under
the countertop
Drain has come looseLeakage under sink
Does not completely drain
Sink wobbles or is loose







16” - 22”
28” - 30”


6” - 7”





DO NOT OVER TIGHTEN THE DRAIN!

ASSEMBLY
Please Note:
• 
• 
• 

• 







• Layout and place 
-


• Drill the countertop

• Place the vessel 


• Use a bead 

• Use a level 

• Secure the vessel





INSTALLATION INSTRUCTIONS
TOOLS NEEDED FOR ASSEMBLY
(not included)
        
4




TOOLS NEEDED FOR ASSEMBLY
(not included)
Quesons, problems, missing parts? Before returning to your retailer, call
our customer service department at 844.404.4242, 8:00 a.m. - 5 p.m., MT,
Monday - Friday or email us at: support@novaoinc.com
GF-136
GF-365
GF-368
Applicable for the following faucet series:
Lock Nut and Screws
Metal Washer
Rubber Washer
Pipe
Hot
Flexible
Hose
Cold
Flexible
Hose
Steps to Complete Your Faucet Install
Hot Hose
O-Ring
Cold Hose
Pipe
Hot Hose
Lock Nut and Screws
Metal Washer
Rubber Washer
Cold Hose
Pipe
• Turn the handles on both the hot and cold water supply lines o so the water will
not be running through the pipes. These water supply lines will be located under
the sink in the cabinet.
• Screw the pipe on to the faucet and make sure the O-ring is on the faucet base.
Fasten the hot and cold exible hoses into the water supply holes on the boom of
the faucet if necessary.
• Carefully lower the faucet through the drilled hole.
• Slide the rubber washer and the 1.5-inch metal washer onto the pipe and ghten
the fastener.
• Aach the exible hose to the supply line source. The exible hose on the right
should be aached to the cold water supply line. The exible hose on the le
should aach to the hot water supply line. Tighten these connecons accordingly.
• With the faucet’s lever wide open, slowly turn the handles on the hot and cold
water supply lines to the open posion to your desired ow rate. Allow the faucet
to run for a couple minutes to get rid of any air pockets in the pipes.
BM-008
BM-012
BM-116
BM-359
TROUBLESHOOTING TIPS
Finish is changing color or is shiny
Abrasive cleaners, soaps or other
factors constantly in contact with it.
Soluon
Stop using abrasives; Replace parts
Issue Reason
New faucet needed; Tighten supply lines
Cracked casing inside; Supply lines
may be loose
Leaking from under the body
Remove ceramic cartridge, check for cracksCartridge may be defecveWater will not shut o completely
Tighten locking nut; Remove cartridge,
check for cracks
Lock nut has come loose; Ceramic
cartridge may be defecve
Leakage under the handle
TYPE ONE ASSEMBLY
Please Note:
• Review and abide by all building and plumbing codes
• Standard codes for Novao faucets: cUPC/CSA/AB1953
• Novao faucets need to be installed by a professional
• A 1.5” faucet hole is needed for installaon
• Max counter thickness 2”
Phillips
TOOLS NEEDED FOR ASSEMBLY
(not included)
Quesons, problems, missing parts? Before returning to your retailer, call
our customer service department at 844.404.4242, 8:00 a.m. - 5 p.m., MT,
Monday - Friday or email us at: support@novaoinc.com
Phillips
Hot
Flexible
Hose
Cold
Flexible
Hose
TROUBLESHOOTING TIPS
Finish is changing color or is shiny
Abrasive cleaners, soaps or other
factors constantly in contact with it.
Soluon
Stop using abrasives; Replace parts
Issue Reason
New faucet needed; Tighten supply lines
Cracked casing inside; Supply lines
may be loose
Leaking from under the body
Remove ceramic cartridge, check for cracksCartridge may be defecveWater will not shut o completely
Tighten locking nut; Remove cartridge,
check for cracks
Lock nut has come loose; Ceramic
cartridge may be defecve
Leakage under the handle
Please Note:
• Review and abide by all building and plumbing codes
• Standard codes for Novao faucets: cUPC/CSA/AB1953
• Novao faucets need to be installed by a professional
• A 1.5” faucet hole is needed for installaon
• Max counter thickness 2”
• Turn the handles on both the hot and cold water supply lines o so
water will not be running through the pipes. These pipes will be located
under the sink in the cabinet.
• Fasten the two bolts into the two threaded holes in the faucet.
Make sure the O-ring is on the base of the faucet.
Fasten the hot and
cold exible hoses into the water supply holes on the boom of the faucet
if necessary.
Lower into the faucet hole.
• Holding the faucet in place at the desired posion, slide the half moon
rubber washer and metal washer up the bolts. Take the two lock nuts
and ghten accordingly.
• Aach the exible hose to the supply line source. The exible hose on
the right should be aached to the cold water supply line. The exible
hose on the le should aach to the hot water supply line. Tighten
these connecons accordingly.
• With the faucet’s lever wide open, slowly turn the
handles on the hot and cold water supply lines to the open posion to
your desired ow rate. Allow the waterfall faucet to run for a couple
minutes to get rid of any air pockets in the pipes
TYPE TWO ASSEMBLY
Steps to Complete Your Faucet Install
Hot Hose
Lock Nut
Metal Washer
Rubber Washer
Cold Hose
Long Bolt
Hot Hose
O-Ring
Cold Hose
Long Bolts
O-Ring
Metal
Washer
Long Bolts
and Lock Nuts
Rubber
Washer
Applicable for the following faucet series:
GF-001
GF-002
GF-010
GF-011
GF-057
NBF-084
Sink
Thin So Rubber Washer
(with drain)
Drain
Pop-up, Umbrella,
or Strainer Drain
Mounng Ring
(if included)
White Rubber Washer
Top View
Floor
Counter
16” - 22”
28” - 30”
Suggested
34” - 37” Suggested
6” - 7”
5.5” - 6”
Counter
(not included)
Concave Washer
Firm Washer
Nut
Tail Pipe
DO NOT OVER TIGHTEN THE DRAIN!
1.5 - 1.625” Hole
(depending on drain)
Mounng Ring
(if included)
TROUBLESHOOTING TIPS
SoluonReasonIssue
Use mounng ring with silicone;
ghten drain
Mounng ring not used; drain is loose
Make sure correct seal is used and
is below bevel
Pop-up is too high; wrong seal used
Tighten the fastener under
the countertop
Drain has come looseLeakage under sink
Does not completely drain
Sink wobbles or is loose
ASSEMBLY
Mounng Ring
(if included)
INSTALLATION INSTRUCTIONS
Please Note:
• Unpack the box and ensure all parts are included.
• Review and abide by all building and plumbing codes.
• Novao drains need to be installed by a professional.
• Disassemble drain and save ALL components.
• Place the vessel on top of the counter and make sure
the drain ts down inside of the counter. If a mounng
ring is used, place it under the sink. The mounng ring
will elevate the sink ½” and provide stabilizaon.
• Use bead of silicone to seal between exterior of vessel
where it is mounted to the mounng ring or counter.
• Use a level to ensure the vessel is level in every
direcon and install the drain.
• Align drain of the sink and tail pipe then parally thread
drain body to tail pipe.
• Connect tail pipe to plumbing then rmly thread drain
to tail pipe.
• Secure the vessel to the counter with fastener on the
drain. Be sure to not over ghten the drain assembly.
Hand ghtening will be sucient.
TOOLS NEEDED FOR ASSEMBLY
(not included)
Quesons, problems, missing parts? Before returning, call our customer service
department at 844.404.4242, 8:00 a.m. - 5 p.m., MST Monday - Friday or e-mail
us at: support@novaoinc.com
Clear Silicone
We would like to take this opportunity to thank
you for choosing Novao. We hope you are
truly sased with our product(s) and enjoy it
for years to come. As a small business, we learn
the most from you, the customer. Please visit
the link below to leave us a review and we’ll
reward you with a $25 Amazon or Visa gi card.
THANK YOU
It’s easy as...
• Go to novaoinc.com
• In the top le, click “product registraon
and review”
•
Find your product model
• Review, submit... enjoy!
P: 844.404.4242 I [email protected] I NovattoInc.com I #WhereStyleFlows
STANDARD SPECIFICATIONS
• Restore cleaner removes water stains and mineral buildup from
glass, porcelain, stainless steel, and stone
• Sealer protects from future corrosion, oxida on and mold
• Ex
cellent for new and exis ng fi xtures
• Sealer is easily applied and cures within seconds
• UV resistant and does not yellow or fl ake
• Treats 100 square feet
• Made in the U.S.A.
NOVGI/RSS
Faucet, Sink Restorer
and Cleaner w/ Sealer
Complete Kit $57
GLACIER ICE
Hard water is a natural result of minerals like calcium and magnesium accumula ng during
the water cycle. This accumula on can be seen as ugly stains on your sinks and faucets. Nova o’s
Glacier Ice products will clean and protect sinks, faucets, counters, shower doors and fi xtures
from hard water deposits. Finally a two-in-one system which will not only remove water stains
and mineral buildup, but also seals from future contaminants.
STANDARD SPECIFICATIONS
• Seals and protects from future hard water
buildup, corrosion, oxida on, mold and mildew
• It is easily applied and cures within seconds
• UV resistant and does not yellow or fl ake
• Perfect for new products
• Made in the U.S.A.
NOVGI/MFC
Faucet and Sink Cleaner
Presoaked wipe with
microfi ber cloth $27
Complete Kit Includes
• Restorer • Super Sealer • Scrubber
• Microfi ber cloth • Spounge
NO
NO
V
V
GI
/
/M
FC
w
w
Complete Kits Includes
• Pre-soaked wipe w/ Super Sealer
• Microfi ber cloth
• Rubber gloves
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Novatto NSFC-CV002NA359ORB Installation guide

NSFC-CV002NA359ORB
Novatto
Brand
Novatto
Model
NSFC-CV002NA359ORB
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents