Noble House 305453 Operating instructions

Type
Operating instructions

This manual is also suitable for

Assembly Instructions
Caution: You must read this before you proceed
Extention Table
Caution: This Table is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Table and to prevent damage to the Table, two adults are needed to
execute this action.
Noble House Home Furnishings LLC
1 ____
Label Picture Description QTY
A Table Top 1
B Leg 4
Label Picture Description QTY
Bolt (M8x60mm) 9
Washer 9
Allen Key 2
Parts List
Assembly Preparation
Before Beginning Assembly:
Hardware
Noble House Home Furnishings LLC
2 ____
Step 1
Unpack and place all parts on a clean, non-marring surface.
This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview
of the Table parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Assembly Steps
Overview
Leg (B)
Table Top (A)
FRONT FACING
Expansion Board of
Table Top (A)
Noble House Home Furnishings LLC
3 ____
Step 3
Stand the Table up, with assistance from your adult partner.
Exert pressure floorwards, onto the Table with both your hands.
This pressure will help the Legs and Table Top reach full alignment status.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts in a sequential manner, until evenly secured.
When tightening the Bolts tighten sequentially.
Do not tighten any Bolt fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and excute the same above process.
If the Table is not Stable it could lead to damage to the product.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Place Table Top(A) facedown, onto a clean, non-marring surface.
Attach Leg(B) to Table Top(A) using Bolts(), and Washers() with Allen Key().
Do not fully tighten the Bolt.
Repeat the same process with the remaining three Legs(B).
Step 2
Noble House Home Furnishings LLC
4 ____
Unlock the Metal Fasteners.
Step 2
Step 1
With an adult partner, gently pull the Table Tops(A) outwards as indicated by the arrows above.
Caution: Do not Lean on or apply pressure to the Table Top when it is pulled open. This could
cause damage to the product.
Extention Steps:
To Extend the Table:
Noble House Home Furnishings LLC
5 ____
3.1) Unfold the Expansion Board of Table Top(A), onto the Center of the Table as shown above.
3.2) Gently push the Table Top(A) inwards until the Top Table(A) fits into the Expansion Board of Table
Top(A).
Caution: Keep hands away from the Table Top(A) and Expansion Board of Table Top(A) when
pushing the Table Top to avoid pinching hazards.
If you can not push the Table Top(A) inwards, just lightly shake the Table Top(A).
Step 4
Step 3
Lock the Metal Fasteners under the Table Top to lock the Expansion Board of Table Top(A) into place
as shown in the above picture.
Your Table is extended and is now ready for use.
This Table can only be used on a flat, level surface.
Noble House Home Furnishings LLC
6 ____
Step 1
Unlock the Metal Fasteners.
Step 2
2.1) With assistance from an adult, gently pull the Top Table(A) outwards as indicated by the arrows
above.
2.2) Fold the Expansion Board of Table Top, back inside of the Table Top as shown above.
Caution: Do not Lean on or apply pressure to the Table Top when it is pulled open. This could
cause damage to the product.
To Retract the Table:
Noble House Home Furnishings LLC
7 ____
Step 3
Step 4
Push the Table Top(A) inwards until both wings of the Table Top(A) align.
Caution: Keep hands away from the Table Top(A) and Expansion Board of Table Top(A) when
pushing the Table Top to avoid pinching hazards.
If you can not push the Table Top(A) inwards, just lightly shake the Table Top(A).
Lock the Metal Fasteners under the Table Top(A) into place as shown in the above picture.
Your Table is retracted and is now ready for use.
This Table can only be used on a flat, level surface.
Noble House Home Furnishings LLC
8 ____
Questions & Answers about Proposition 65
• What is Proposition 65?
Proposition 65 requires businesses to provide warnings to Californians about significant
exposures to chemicals that cause cancer, birth defects or other reproductive harm.
These chemicals can be in the products that Californians purchase, in their homes or
workplaces, or that are released into the environment. By requiring that this information be
provided, Proposition 65 enables Californians to make informed decisions about their
exposures to these chemicals.
Proposition 65 also prohibits California businesses from knowingly discharging significant
amounts of listed chemicals into sources of drinking water.
Proposition 65 requires California to publish a list of chemicals known to cause cancer,
birth defects or other reproductive harm. This list, which must be updated at least once a
year, has grown to include approximately 900 chemicals since it was first published in
1987.
• What types of chemicals are on the Proposition 65 list?
The list contains a wide range of naturally occurring and synthetic chemicals that include
additives or ingredients in pesticides, common household products, food, drugs, dyes, or
solvents. Listed chemicals may also be used in manufacturing and construction, or they
may be byproducts of chemical processes, such as motor vehicle exhaust.
• What does a warning mean?
If a warning is placed on a product label or posted or distributed at a workplace, a
business, or in rental housing, the business issuing the warning is aware or believes that it
is exposing individuals to one or more listed chemicals.
By law, a warning must be given for listed chemicals unless the exposure is low enough to
pose no significant risk of cancer or is significantly below levels observed to cause birth
defects or other reproductive harm.
• Where can I get more information on Proposition 65?
If you have specific questions on the administration or implementation of Proposition 65,
you can contact OEHHA's Proposition 65 program at P65.Question[email protected]a.gov, or by
phone at (916) 445-6900.
Noble House Home Furnishings LLC
9 ____
Label Picture Description QTY
A Backrest 1
B Seat 1
C Right Armrest / Leg 1
Caution : You must read this before you proceed
Dinning Chair
Page 1 OF 5
D Left Armrest /Leg 1
E Seat Cushion 1
Label Picture Description QTY
F Bolt(M6*35MM) 12
G Washer 12
H Allen Key 1
Before
Beginning
Assembly:
Page 2 OF 5
Step 1
Open the carton and place all the parts onto a clean and soft surface.
Unpack all packages of hardware.
Place the Backrest (A) with its inside facing skywards.
Attach Seat(B) to Backrest(A) using Hardware(H, G) with Allen Key(H).
LOOSELY TIGHTEN.
ATTENTION: Occasionally some of the PE Wicker shifts and covers the
mounting positions preventing easy assembly.
The PE wicker should never be cut, but moved away from the mounting
positions.
Step 2
Place the Right Armrest/Leg(C), as picture above so as to be attached to the
Backrest (A) and Seat(B) using Hardware(F, G) with Allen Key(H).
LOOSELY TIGHTEN.
Page 3 OF 5
Step 3
Place the Left Armrest/Leg (D) as pictured above and affix to Backrest (A)
and Seat(B) using Hardware(F, G) with Allen Key(H) as shown in Picture 4
and Picture 5.
LOOSELY TIGHTEN.
Step 4
Stand CHAIR rightside up.
Check stability and then tighten the bolts.
Note: DO NOT fully tighten a BOLT in one go and then move on to the
next. Rather, In a sequential manner, gradually tighten each Bolt until
all bolts are evenly secured. This methodology will ensure maximum
evenness once all Bolts are fully tightened.
Step 5
Put the Seat Cushion(E) on the Seat.
Your Chair is ready for use.
Page 4 OF 5
Page 5 OF 5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Noble House 305453 Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI