AAT NVIP-3DN3520SD/IRH-2 User manual

Page is loading ...

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

 Electromagnetic compatibility EMC 2004/108/EC.

 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic

Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will

help to prevent potential negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/EU

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous

substances in electrical and electronic equipment, have been designed and manufactured in

compliance with the above mentioned regulations. Simultaneously, we claim that our products have

been tested and do not contain hazardous substances whose exceeding limits could have negative

impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF

EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

3

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO

USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE

PERSONNEL MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6.

Usage of additional devices and components neither provided nor recommended by the producer

is forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the newest manual

Data included in the following user’s manual is up to date at the time of printing. AAT Holding Sp z o.o. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

4

TABLE OF CONTENTS

1. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................6

1.1. Overview ..........................................................................................................6

1.2. Starting the IP camera .......................................................................................6

1.3. Initial configuration via the Web browser..........................................................7

2. NETWORK CONNECTION UTILIZING WEB BROSWER .................................8

2.1. Recommended PC specification for web browser..............................................8

2.2. Initial configuration via the Web browser..........................................................8

3. WWW INTERFACE - WORKING WITH IP CAMERA .......................................12

3.1. Displaying live pictures...................................................................................12

4. SETTINGS .................................................................................................................14

4.1.System ....................................................................................................... ….14

4.1.1 Basic information…………………………………………………….….14

4.1.2 Data and Time……………………………………………………..….....15

4.1.3 Local Settings……………………………………………………..…......15

4.2. Image.……………………………………………………………………….…..16

4.2.1. Video/Audio………………………………………………………….…16

4.2.2 OSD……………………………………………………………….....…..17

4.2.3 Camera Setup……………………………………………………………18

4.3 PTZ……………………………………………………………………...….……20

4.3.1 Settings………………………………………………………...….……..20

4.3.2 Restore…….…………………………………………………...………..20

4.3.3 PTZ Setup……………………………………………………..…….…..21

4.4 Alarm………………………………………………………………...…….…….28

4.4.1 Motion detection…………………………………………...……….…...28

4.4.2 Alarm input………………………………………………...……………30

4.4.3 Alarm output……………………………………………..………….…..31

4.5. Network…………………………………………………………..……….…….32

4.5.1 TCP/IPv4………………………………………………..………………32

4.5.2 Ports…………………………………………………..…………………32

4.5.3 DDNS………………………………………………..………………….32

4.5.4 SNMP………………………………………………..………………….32

4.5.5 RTSP……………………………………………….…………………...33

4.5.6 UPNP…………………………………………………………………...34

Page is loading ...

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

6

1. START-UP AND INITIAL IP CAMERA CONFIGURATION

1.1. Overview

Following manual for IP Cameras NVIP-3000 series contains detailed information about camera

connection and operation, main page introduction, system related settings and camera settings.

Note

In this document you can find all available functionality present in described series of cameras.

Depending on camera model some features might be unavailable or unsupported.

1.2. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch and

you have to connect 24 VAC power adaptor, at least 30W.

Initialization process takes about 2 minutes. Then you can proceed to connect to the camera via web

browser.

The recommended way to start an IP camera and perform its configuration is connect directly to the

network switch which is not connected to other devices.

To obtain further information about network configuration parameters (IP address, gateway, network

mask, etc.) please contact your network administrator.

 Network connection using external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network

transmission

Network Switch

Computer

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

7

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

 Network connection using external power supply, directly to the computer.

1.3. Initial configuration via the web browser

The default network settings for IP PTZ cameras 5000 series are :

1. IP address = 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to set PC IP address appropriately, so the two devices can

operate in one network subnet (e.g. for IP 192.168.1.1, appropriate address for the camera is from range

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

8

2. NETWORK CONNECTION VIA WEB BROSWER

2.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming image display in 1920x1080

resolution and 30 fps speed.

1. CPU Intel Core i3 3GHz or faster

2. RAM Memory min. 4 GB

3. VGA card (any displaying Nvidia GeForce 512MB Ram or equal)

4. OS Windows 7 / 8 / 8.1 / 10

5. Network card 100/1000 Mb/s

2.2. Connection with IP camera via web browser

Enter camera IP address in the address bar. When user connect to the camera, web browser will

download the applet for displaying images from the camera. In Internet Explorer it may be necessary to

accept an ActiveX control. To do this, click the right mouse button on the message, select "Install

Active X control" and click Install. After successfully NetIPCamera plug in downloading run and

install it on a computer.

NETWORK CONNECTION VIA WEB BROWSER

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

9

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please choose: Tools > Internet options > Security tab > Custom level and:

 Under Download unsigned ActiveX controls - select either Enable or Prompt

 Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

User can also add the camera’s IP address to “trusted zone” and set lowest security level for it.

In addition, when applet is working in Windows Vista/7 the ActiveX it may be blocked by Windows

Defender or User account control. In such case user should allow to run this applet, or simply disable

these functions.

After successful installation login window will be displayed. Default user is root and default password

is pass. For safety reasons, it is recommended to change default user name and password.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

10

NETWORK CONNECTION VIA WEB BROWSER

NOTE: If user is running Windows 7/8 with Internet Explorer 11, the ActiveX applet can be blocked

through browser security settings. In this situation, you should: add the IP address of the camera to the

view of compatibility (Tools -> Compatibility View Settings, click Add).

Then, in the security settings, add the camera address to trusted sites and lower the security level to a

minimum.

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

11

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

NETWORK CONNECTION UTILIZING WEB BROWSER

After making the changes, restart the browser, re-connect to the camera and log on.

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

12

3. WWW INTERFACE - WORKING WITH IP CAMERA

3.1. Displaying live video

1. Option tabs

Live - live view

Config - advenced config

Search - records menu

Logout - logout from camera

2 Live stream settings

Selection of the stream displayed in Live View, as well as the delay of the displayed image.

3. Live view size

Orginal Size

Fit to screen

WWW INTERFACE - WORKING WITH IP CAMERA

2.

1.

3.

4.

5.

Automatic size

Full screen

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

13

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

4. Camera Functions

5. PTZ Menu

PTZ control

PTZ control speed

Autoscan

Wiper (option not supported)

IR mode (ON/OFF/AUTO)

Random Scan

Group Scan

Preset Menu

Track Menu

Cruise Menu

Delete Preset

Call Preset

Save Preset

WWW INTERFACE - WORKING WITH IP CAMERA

Live view on/off

Mic. on/off

Sound on/off

Get snapshoot

Video Recording

PTZ control on screen

Digital zoom

PTZ Menu

Motion detection

Alarm

Optical zoom

Sharpness value

Iris

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

14

4. SETTINGS

4.1 System

4.1.1 Basic information

The menu displays basic information about the camera, such as device type, brand, software version,

software build date (date of creation of the software version), kernel version, hardware version, onvif

version, OCX version, MAC address, version of the PTZ and camera type.

SETTINGS

00:1B:9D:AF:00:D1

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

15

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

4.1.2 Date and Time

Zone

The user selects the time zone for his own region, and also selects the option DST (daylight saving)

Date and Time

User can choose type of time synchronization

Synchronize with NTP - the camera uses connection to the NTP server to update the current date and

time

Synchronize with PC - camera synchronizes time with the current time of the computer

Set manually - manually set the time and date

4.1.3 Local config

The tab is used to define the directory in which photos and videos being saved (default is:

C:\Users\user_name\Favorites). Additionally, there is the option to disable sound recording, on

records.

SETTINGS

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

16

4.2 Image

4.2.1 Video/Audio

Video

Stream - name of streams

Resolution - resolution selection for each stream. Depending on the stream different resolutions are

available.

Frame Rate - defining the maximum number of frames per second for a given stream

Bitrate - camera has two modes available for streaming live video VBR and CBR

VBR - variable stream size depends on the amount and rate of change occurring in the image

CBR - constant stream size defined by the user

Bitrate (Kbps) - available only on CBR mode, depending on the camera model, select the value of the

bandwidth stream. The image quality will changes depending on the selected value.

Video - available only on VBR mode, available options: Highest, High, Medium, Low and Lowest.

Bitrate values will change depending on the option selected.

I Frame - define key frame intervals, range from 25 to 100. The default setting: 25

Video - type of encoding stream, possible types of coding: H264 / H265

Profile - choice of stream profile of the possible options available: High profile, Main profiles, Base

Line.

Video encode slice split - mode off by default.

Stream for snapshoot - User can select the snapshoot quality from 3 possible resolution.

Audio

Audio settings allow to choose the Audio Codec and input selection (LIN / MIC)

SETTINGS

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

17

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

4.2.2 OSD

Information display on screen in live view camera.

The camera has the ability to display the following information on the displayed image:

Date format - camera displays the current date in a user selected format (YYYY / MM / DD, MM /

DD / YYYY, DD / MM / YYYY)

Device name - Display settings OSD information on the background of the camera image.

OSD contents - an additional OSD string you can put on the displayed image.

Each of the selected values can be moved by dragging it to the image displayed across the screen.

SETTINGS

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

18

4.2.3 Camera Setup

BLC - back light compensation function, disabled by default

Colour level - set the color saturation of the 0-7 range

Brightness - adjusts the brightness of the image with the range 0-14

Sharpness - adjusts the sharpness of 0-20, disabled by default

3D DNR - DNR (Digital Noise Reduction) level settings, possible options: Auto, Low, Medium, High

Fog - for enhanced visibility in case of fog, the settings in the range of 1-4, disabled by default

Focus Limit - set the distance limit at which the camera will not focus, if on current screen show new

object, possible options: 30cm, 1m, 1.5m, 3m, 5m, 10m.

Zoom Display - option to display the optical zoom on the displayed image.

Zoom speed - option to change value of optical zoom speed, the available range 1-3.

Camera initial - positioning optical zoom camera module.

Set North - unsupported feature

SETTINGS

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

19

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

PAL / NTSC - switching between PAL and NTSC modes

Exposure - option to change operating mode of auto exposure from following: Auto, Brightness,

Shutter, Aperture, Manual mode. Depending on the selected mode, there are additional

configuration options such as Brightness, Shutter, Aperture, Gain.

White Balance - set the white balance depending on the observed area, possible settings: Indoor,

Outdoor, Manual

AGC - Auto Gain level setting 1-15

Mirror mode - option to change display settings available modes: Mirror Image, Rotate, Flip.

Day / Night Mode - option to change illumination mode, switching between Auto/Day/Night, also

ability to set the Schedule, the default mode is Auto.

IR sensor sensitivity - sensitivity of IR sensor options: Low, Medium, High, Set - in the mode set,

the user manually determines the level (threshold on, threshold off) at which the IR will be switched.

Default - Return to default settings of camera

Restart - reset the changes made to the last saved state

SETTINGS

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

20

4.3 PTZ

4.3.1 Settings

PTZ settings

Auto PTZ Flip- camera after reaching the lower limit of the movement perform 180º image rotation

Language - user can choose language in OSD menu called by command PRESET 95

Menu Keeping Time - the function is disabling OSD menu after a period of specified time (15 sec - 2

min)

Other

A four-digit password to gain access to the OSD menu, other than the administrator.

WARNING!

The camera has a built-in OSD menu invoked by using the PRESET 95. The menu is accessed from the

normal user, and allows to change configuration of the camera. It is recommended to use a four-digit

password in order to reduce the possibility of changes to the settings by users who do not have

administrator rights.

4.3.2 Restore

The camera has two options for restoring the PTZ

RESET - camera cancel all PTZ activities (patrols, route), and erase function of the park (the camera

does not erase set presets and patrols).

CLEAR - completely delete all PTZ settings and restore the factory settings.

SETTINGS

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

21

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

4.3.3 PTZ Setup

Preset

The tab allows to configure presets (programmable shots) in the camera. In order to define it user need

to press Create button, and following window will appear:

User defines the next preset number and its name (letters and numbers). After pressing the OK button,

the preset is added to the list of existing presets.

Saved presets can be called, modified by changing the area to be observed and then pressing the Save

button position, or deleted by using the Delete button.

WARNING!

If user use the standalone recorders NOVUS®, nr of preset recorded by the recorder corresponds to

preset of the camera. The recorder, however, does not recognize the presets previously saved in the

camera by the user.

SETTINGS

NVIP-3000 series IP PTZ camera - user manual ver.1.0.

22

C r u i s e

The camera has a function that allows to create a patrol scheme observation composed by 16 shots of

Presets. Using the Create button, the user adds a new patrol to the existing list. A window appears in

which after entering the Patrol name, user can add presets using the Add preset button.

In the new window, user can add next presets defined by user earlier.

SETTINGS

Page is loading ...

AAT NVIP-3DN3520SD/IRH-2 User manual

This manual is also suitable for

AAT NVIP-3DN3520SD/IRH-2 User manual

in other languages

Related papers

Other documents