Troy-Bilt 21A34M8711 User manual

Category
Mini tillers
Type
User manual

This manual is also suitable for

TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
OperatOrs Manual
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
Front Tine Tiller — 340 Series
Form No. 769-08539
(October 15, 2012)
To The Owner
1
2
Safe Operation Practices ........................................ 3
Assembly & Set-Up .................................................. 7
Controls ...................................................................10
Operation ................................................................ 11
Maintenance & Adjustment .................................13
Service .....................................................................15
Troubleshooting .....................................................16
Replacement Parts .................................................17
Warranty ..................................................Back Cover
Table of Contents
Customer Support
Please do NOT return the machine to the retailer or dealer without first contacting the Customer Support Department.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:
Visit us on the web at www.troybilt.com
See How-to Maintenance and Parts Installation Videos at www.troybilt.com/tutorials
Call a Customer Support Representative at (800) 828-5500 or (330) 558-7220

Thank you for purchasing a Troy-Bilt Garden Tiller. It was
carefully engineered to provide excellent performance when
properly operated and maintained.
Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain your machine. Please be sure that you, and any other
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.
All information in this manual is relative to the most recent
product information available at the time of printing. Review
this manual frequently to familiarize yourself with the machine,

Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. We reserve
the right to change product specifications, designs and
equipment without notice and without incurring obligation.
If you have any problems or questions concerning the machine,
phone a authorized Troy-Bilt service dealer or contact us directly.

address and mailing address can be found on this page. We want
to ensure your complete satisfaction at all times.
Throughout this manual, all references to right and left side of the
machine are observed from the operating position
The engine manufacturer is responsible for all engine-related
issues with regards to performance, power-rating, specifications,


machine, for more information.
Thank You
Record Product Information
Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the

down at the tine shield. This information will be necessary,
should you seek technical support via our web site, Customer
Support Department, or with a local authorized service dealer.
Model NuMber
Serial NuMber
Important Safe Operation Practices
2
3
Training
 Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
3. 

the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
 Never allow adults to operate this machine without proper
instruction.
5. Keep the area of operation clear of all persons, particularly
small children and pets. Stop machine if anyone enters the
area.
Preparation
 Thoroughly inspect the area where the equipment is to
be used. Remove all stones, sticks, wire, and other foreign
objects which could be tripped over and cause personal
injury.
2. Wear sturdy, rough-soled work shoes and close fitting
slacks and shirt. Loose fitting clothes or jewelry can be
caught in moving parts. Never operate this machine in bare
feet or sandals.
3. Disengage clutch levers and shift (if provided) into neutral
(“N”) before starting the engine.
 Never leave this machine unattended with the engine
running.
5. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the

Safe Handling of Gasoline:
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
DANGER! This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet. Failure to observe the following safety instructions could result in serious
injury or death.
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and reproductive
harm. Wash hands after handling
Section 2 — important Safe operation practiceS4
 After striking a foreign object, stop the engine, disconnect
the spark plug wire and ground against the engine.
Thoroughly inspect the machine for any damage. Repair
the damage before starting and operating.
 Disengage all clutch levers (if fitted) and stop engine
before you leave the operating position (behind the
handles). Wait until the tines come to a complete stop
before unclogging the tines, making any adjustments, or
inspections.
 Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
 Muffler and engine become hot and can cause a burn. Do
not touch.
 Use caution when tilling near fences, buildings and
underground utilities. Rotating tines can cause property
damage or personal injury.
 Do not overload machine capacity by attempting to till soil
too deep at too fast of a rate.
 If the machine should start making an unusual noise or
vibration, stop the engine, disconnect the spark plug wire
and ground it against the engine. Inspect thoroughly for
damage. Repair any damage before starting and operating.
 Keep all shields, guards, and safety devices in place and
operating properly.
 Never pick up or carry machine while the engine is running.
20. Use only attachments and accessories approved by the
manufacturer. Failure to do so can result in personal injury.
 If situations occur which are not covered in this manual, use
care and good judgement. Contact Customer Support for
assistance and the name of you nearest servicing dealer..
Maintenance & Storage
 Keep machine, attachments and accessories in safe
working order.
2. Allow a machine to cool at least five minutes before
storing. Never tamper with safety devices. Check their
proper operation regularly.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
 Before cleaning, repairing, or inspecting, stop the engine
and make certain the tines and all moving parts have
stopped. Disconnect the spark plug wire and ground it
against the engine to prevent unintended starting.
5. Do not change the engine governor settings or over-speed
the engine. The governor controls the maximum safe
operating speed of engine.
 Maintain or replace safety and instruction labels, as
necessary.
7. Follow this manual for safe loading, unloading,
transporting, and storage of this machine.
8. 
if the machine is to be stored for an extended period.
c. When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment on
a trailer with a portable container, rather than from a
gasoline dispenser nozzle.
d. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
e. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
f. Never fuel machine indoors.
g. Never remove gas cap or add fuel while the engine
is hot or running. Allow engine to cool at least two
minutes before refueling.
h. Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to allow space for
fuel expansion.
i. Replace gasoline cap and tighten securely.
j. If gasoline is spilled, wipe it off the engine and
equipment. Move unit to another area. Wait 5
minutes before starting the engine.
k. To reduce fire hazards, keep machine free of grass,
leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.
l. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
as on a water heater, space heater, furnace, clothes
dryer or other gas appliances.
Operation
 Do not put hands or feet near rotating parts. Contact with
the rotating parts can amputate hands and feet.
2. Do not operate machine while under the influence of
alcohol or drugs.
3. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles.
 Keep bystanders away from the machine while it is in
operation. Stop the machine if anyone enters the area.
5. Be careful when tilling in hard ground. The tines may catch
in the ground and propel the tiller forward. If this occurs,
let go of the handle bars and do not restrain the machine.
 Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic. Do
not carry passengers.
7. Never operate the machine at high transport speeds on
hard or slippery surfaces.
8. Exercise caution to avoid slipping or falling.
 Look down and behind and use care when in reverse or
pulling machine towards you.
 Start the engine according to the instructions found in this
manual and keep feet well away from the tines at all times.
Section 2 — important Safe operation practiceS
5
 If the fuel tank has to be drained, do this outdoors.
 
etc. to protect the environment.
 According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
Notice Regarding Emissions
Engines which are certified to comply with California and federal

are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
Spark Arrestor
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered,
brushcovered or grass-covered land unless the

arrestor meeting applicable local or state laws (if
any).
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the


apply on federal lands.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service

Section 2 — important Safe operation practiceS6
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol Description

Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate

Do not put hands or feet near rotating parts. Contact with the rotating parts can amputate
hands and feet.

Do not put hands or feet near rotating parts. Contact with the rotating parts can amputate
hands and feet.

Allow the engine to cool at least two minutes before refueling.

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.

Engine parts, especially the muffler, become extremely hot during operation. Allow engine
and muffler to cool before touching.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
Assembly & Set-Up
3
7
Assembly
References to the right and left side of tiller are determined from
behind the equipment in the operating position.
Recommended Tools for Assembly
 ” open-end wrench
 ⁄” open-end wrench
 Clean oil funnel
 
specifications and quantity required.
Handle
 
Forward Clutch Cable
Figure 1-1
NOTE: Be sure not to kink cables while attaching.
2. Hook the “Z” end of the forward clutch cable into the tine

Figure 1-2
3. Remove the hex screw and bell washer from the right side of
the frame. Hold the cable guide bracket on the left side of frame

2
1
3
Hex Screw
Hex Screw
Bell Washer
Bell Washer
Cable Guide
Bracket
Handle
Figure 1-3
 
5. Insert the bolt through the cupped washer, frame, handle
and into the cable guide bracket (note the notch in the
cable guide bracket goes over the flange on the frame.)

Contents of Carton
     
   
8 Section 3— ASSembly & Set-Up
2. Insert the depth stake assembly into the frame and reinstall
the two screws removed earlier. Tighten the hex bolts

Screws
Depth Stake
Assembly
Figure 1-6
Secure the pin with the clip removed earlier. The depth stake can
be placed at various positions. For setup purposes it is suggested
that the depth stake be assembled with the stake just above or
level with the ground surface. For further instructions on the

Adjustments
Wheels
The tiller is shipped with the wheels adjusted so that the
machine sits level. The wheels need to be adjusted to meet
your tilling needs before operation. This adjustment is made
by removing the clevis pin from the wheel yoke and raising the

Clevis
Pin
Cotter
Pin
Wheel Yoke
Depth
Stake
Figure 1-7
 Tighten the bolt securely after securing the handle brace as

Carriage Screw
Handle Brace
Bell Washer
Hand Knob
Figure 1-4
7. Locate the carriage screw, bell washer and hand knob
packed with your tiller.
8. Insert the carriage screw through the bracket on the
handle, bell washer, handle brace and into the hand knob.

 Select one of the three handle height positions (three notches
in the welded handle bracket) and tighten the hand knob

Return to the lower handle and tighten the hex bolt securely.
Depth Gauge
 Remove the two screws from the depth stake assembly.

Depth Stake
Assembly
Screws
Figure 1-5
9Section 3 — ASSembly & Set-Up
Clutch Cable Adjustment
Before operating the tiller the adjustment of the forward clutch
cables must be checked.
 Disconnect and ground the spark plug wire against the
engine.
2. Adjust the forward clutch cable by loosening the hex nut.

Hex Nut
Cable Collar
Figure 1-8
3. Turn the cable collar section one or two turns to increase or

 
5. With the forward engagement handle in the neutral —
released — position, pull the starter rope several times. The
tines should not turn.
 If they turn adjust the forward clutch cable to release
tension using the previous steps in this section.
7. Check again for correct tension on the cable.
8. After tilling, if the tines stop moving, re-adjust the cables.
Set-Up
Gas & Oil Fill-Up
Service the Engine with gasoline and oil as instructed in the

the instructions carefully.
WARNING! Use extreme care when handling
gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel the machine
indoors or while the engine is hot or running.
Controls & Features
4
10
Handle
Tiller Tines
Depth Stake
Handle Knob
Forward Tine
Engagement Lever
Engine Controls

functions of the engine controls.
Forward Tine Engagement Lever
The forward tine control lever is located beneath the upper
section of the handle. Squeezing the lever against the handle
engages the tine drive. Release the lever to stop the tines.
Depth Stake
The depth stake controls the tilling depth.
Tiller Tines
Tilling tines are used to cultivate, furrow and prepare your
garden for seeding.
Handle Knob
The handle height may be adjusted. Loosen the knob to change
the position. Tighten hardware when complete.
Operation
5
11
Starting & Stopping the Engine
WARNING! Read, understand, and follow all the
instructions and warnings posted on the machine
and in this manual before operating.
WARNING! Be sure no one is standing in front of
the tiller while the engine is running or being
started.
 Make sure that the tine clutch control is disengaged and

and stopping instructions.
Setting the Depth
Yoke Forward
Place the wheel yoke so that wheels are forward (nearest to tines)

Figure 1-1
Yoke to Back
Place the wheel yoke so that wheels are toward the rear — closest

Figure 1-2
Depth Stake
The depth stake acts as a brake for the tiller and controls the depth
and speed at which the machine will operate. Remove the clevis

Figure 1-3
12 Section 5— operation
Cultivating Procedures
For cultivating, a 2-3” depth is desirable. The tine width can

from the tiller. See the Maintenance & Adjustments Section for
instructions on removing the tines.
When laying out plant rows, be sure to allow enough width to
permit cultivation between the rows. In growing corn or similar
crops, check-row planting will permit cross cultivation and

Figure 1-5
Other Uses
The tiller has many uses other than tilling and cultivating a

The tiller will prepare a deep seed bed which will be free of hard
untilled spots, allowing a better stand of grass to grow. The tiller
is very useful for loosening hard soil for excavation with a shovel;
No tedious handwork will be necessary. Your tiller may be used
for mixing compost in the pile or for mixing it with the soil in
your garden. This should be done after the soil has been broken
to the full working depth. The compost should be worked in to

garden and then by making separate passes across its width. The
addition of decayed organic matter will substantially increase
the fertility of your garden. For proper decaying action, fertilizer
should be applied and worked in with the mulch materials.
Breaking up leaves and straw and mixing it with several inches of
soil allows proper aeration of the plant root system and retards
the growth of weeds.
Handle Pressure
Further control of the tilling depth and travel speed can be
obtained by variation of pressure on the handles.
A downward pressure on the handles will reduce the working depth
and increase the forward speed. An upward pressure on the handles
will increase the working depth and reduce the forward speed.
The type of soil and working conditions will determine the actual
setting of the depth stake and the handle pressure required.
Transporting and Storing the Tiller
To transport and store the tiller move the throttle to the stop
position. Pivot the depth stake away from ground up between

Using Your Tiller
Your tiller is designed for seed bed preparation, cultivating,
furrowing and mulching.
Tilling Procedure
When tilling, leave approximately 8” of untilled soil between the
first and second tilling paths, then make the third path between

12 34 5
Figure 1-4
In some soils, the desired depth is obtained the first time over
the garden. In other soils, the desired depth is obtained by going
over the garden two or three times. Passes should be made
across the length and width of the garden alternately. Rocks
which are turned up should be removed from the garden area.
Maintenance & Adjustments
6
13
WARNING! Disconnect the spark plug wire and
ground it against the engine before performing any
repairs.
Maintenance
Engine

maintenance instructions.
Tines
Clean the underside of the tine shield after each use. The dirt
washes off the tines easier if rinsed off immediately instead of
after it dries. Always towel dry the tiller afterwards and apply a
light coat of oil or silicone to prevent rusting or water damage.
NOTE: Never use a “pressure washer” to clean your tiller. Water
can penetrate tight areas of the tiller and its chain case and cause
serious damage to machine.
Lubrication
Pivot Points
Remove the belt cover and lubricate all the pivot points and
linkages at least once a season with light oil. Keep the belts free
of lubrication.
Tine Shafts
Remove the tine assemblies and lubricate the tine shafts at least
once a season.
Wheel Shafts
Remove the wheel assemblies and lubricate the axle shafts at
least once a season.
Chain Drive
The chain drive is pre-lubricated and sealed at factory.
Adjustments
Cable Adjustment
Refer to the Assembly & Set-Up section of this manual for
instructions on adjusting the forward and reverse cables.
Tines
Tilling Width
With the outer tines installed, the working width of the machine

and cotter pins, sliding each outer tine outward away from the
center of the tiller and re-securing the pins in the holes provided.

Cotter Pin
Clevis Pin
Outer Tine
24”
26”
Cutting Edge
Forward
Rotation
Figure 1-1
14 Section 6— Maintenance & adjuStMentS
Tine Inspection
The bolo tines will wear with use and should be inspected
at the beginning of each tilling season and after every 30
operating hours. The tines can be replaced either individually
or as a complete set. See the Replacement Parts Section for tine
identification and part numbers.
With use, the tines will become shorter, narrower and pointed.
Badly worn tines will result in a loss of tilling depth, and reduced
effectiveness when chopping up and turning under organic matter.

Rear/Operator
Hex Lock Nut
Cotter Pin
Clevis Pin
Front/Forward
Hex Screw
Cutting Edge
Forward
Rotation
Figure 1-2
Removing/Installing a Single Tine
 With the engine shut off and the spark plug wire
disconnected, remove the two hex screws (⁄
and hex lock nuts (⁄
holder. If needed, use penetrating oil on the nuts.
2. When installing a single tine, be sure to position it so that
its cutting edge (sharp) will enter the soil first as the tiller
moves forward.
Removing/Installing a Tine Assembly:
 A tine assembly consists of eight tines mounted on a tine
holder.
2. If removing both tine assemblies, mark them “left” and
“right” before removal. Remove the hex screw (⁄
and flange lock nut (⁄
the tine shaft. If necessary, use a rubber mallet to tap the tine
assembly outward off the shaft.
3. Before reinstalling the tine assembly, inspect the tine
shaft for rust, rough spots or burrs. Lightly file or sand, as
needed. Apply a thin coat of grease to the shaft.
 Install each tine assembly so that the cutting (sharp) edge
of the tines will enter the soil first when the tiller moves
forward. Secure the tine assembly to the tine shaft using
the screw and locknut.
Off-Season Storage
If the tiller will not be used for a period longer than 30 days, the
following steps should be taken to prepare the tiller for storage.
 Clean the exterior of the engine and the entire tiller
thoroughly. Lubricate the tiller as described in the
lubrication instructions.
2. The use of pressure washers is not recommended for
cleaning your tiller. They may cause damage to electric
components, spindles, pulleys, bearings or the engine. The
use of pressure washers will result in shortened life and
reduce serviceability.
3. Refer to the engine manual for correct engine storage
instructions.
 Wipe tines with oiled rag to prevent rust.
5. Store tiller in a clean, dry area. Do not store next to
corrosive materials, such as fertilizer.
NOTE: When storing any type of power equipment in
an unventilated area or metal storage shed, care should
be taken to rustproof the equipment. Using a light oil or
silicone, coat the equipment and especially any springs,
bearings, and cables.
Se rvice
7
15
Belt Replacement
Your tiller has been engineered with a belt made of special
material (Kevlar Tensile) for longer life and better performance. It

through you authorized service dealer.
 Disconnect and ground the spark plug wire against the engine.
2. Remove the belt cover from the left side of the tiller by
removing the two hex washer screws and the lock nut and

Hex Washer Screws
Lock Nut
Flat Washer
Belt Cover
Figure 1-1
3. Remove the idler pulley bolt and move the belt from under

Idler Pulley Keeper
Idler Pulley
Bolt
Figure 1-2
 Using a ” wrench, remove the hex screw securing the belt

Hex Screw
Belt Keeper
Figure 1-3
5. Remove the belt.
 To install the new belt, follow the instructions in reverse

side of the belt away from the engine and transmission
pulleys.
Transmission
Pulley
Idler Pulley
Engine Pulley
Figure 1-4
NOTE: Upon reassembly, make certain that the idler pulley

on the bottom of the keeper and the alignment when
reassembling with the replacement belt.
Troubleshooting
8
16
Problem Cause Remedy
Tines do not engage  Foreign object lodged in tines
2. Tine clevis pin(s) missing
3. Pulley and idler not in correct adjustment
 Control cable not adjusted properly
5. Belt worn and/or stretched
 Dislodge foreign object
2. Replace tine clevis pin(s)
3. Take tiller to authorized service dealer
 Adjust control cable
5. Replace belt
Tines skip over ground  Improper rotation.  Forward rotation should only be used on soil
that has already been tilled, not on virgin soil.
Wheels do not engage  Clevis pin missing
2. Control cable not adjusted properly
3. Belt worn and/or stretched
 Replace clevis pin
2. Adjust control cable
3. Replace belt
Replacement Parts
9
17
Component Part Number and Description
 
 
 
 
 
 
 
 
 
Phone (800) 828-5500 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).
Parts Manual downloads are also available free of charge at www.troybilt.com.
MANUFACTURER’S LIMITED WARRANTY FOR
GDOC-100023 REV. C
The limited warranty set forth below is given by Troy-Bilt LLC with
respect to new merchandise purchased and used in the United
States and/or its territories and possessions, and by MTD Products
Limited with respect to new merchandise purchased and used
in Canada and/or its territories and possessions (either entity
respectively, “Troy-Bilt).
This warranty is in addition to any applicable emissions warranty
provided with your product.
Troy-Bilt” warrants this product (excluding its Belts, Transmission
and Attachments as described below) against defects in material
and workmanship for a period of two (2) years commencing
on the date of original purchase and will, at its option, repair or
replace, free of charge, any part found to be defective in materials
or workmanship. This limited warranty shall only apply if this
product has been operated and maintained in accordance with

been subject to misuse, abuse, commercial use, neglect, accident,
improper maintenance, alteration, vandalism, theft, fire, water,
or damage because of other peril or natural disaster. Damage
resulting from the installation or use of any part, accessory or
attachment not approved by Troy-Bilt for use with the product(s)
covered by this manual will void your warranty as to any resulting
damage.
Belts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of
purchase.
Transmission — Troy-Bilt warrants the transmission (including
all gears, shafts and housings) against defects in material and
workmanship for the life of the tiller, to the original purchaser only,
commencing on the date of original purchase or lease.
Attachments — Troy-Bilt warrants attachments for this product
against defects in material and workmanship for a period of one

purchase or lease. Attachments include, but are not limited to items
such as: grass collectors and mulch kits.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH

To locate the dealer in your area:
In the U.S.A.



In Canada


This limited warranty does not provide coverage in the following
cases:
a. The engine or component parts thereof. These items may


b. Log splitter pumps, valves, and cylinders have a separate one-
year warranty.
c. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
d. Service completed by someone other than an authorized service
dealer.
e. Troy-Bilt does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and their
respective possessions and territories, except those sold through

f. Replacement parts that are not genuine Troy-Bilt parts.
g. Transportation charges and service calls.
h. Troy-Bilt does not warrant this product for commercial use.
No implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose, applies
after the applicable period of express written warranty above
as to the parts as identified. No other express warranty,
whether written or oral, except as mentioned above, given
by any person or entity, including a dealer or retailer, with
respect to any product, shall bind Troy-Bilt. During the period
of the warranty, the exclusive remedy is repair or replacement
of the product as set forth above.
The provisions as set forth in this warranty provide the sole
and exclusive remedy arising from the sale. Troy-Bilt shall
not be liable for incidental or consequential loss or damage
including, without limitation, expenses incurred for substitute
or replacement lawn care services or for rental expenses to
temporarily replace a warranted product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
In no event shall recovery of any kind be greater than the amount
of the purchase price of the product sold. Alteration of safety
features of the product shall void this warranty. You assume the
risk and liability for loss, damage, or injury to you and your property
and/or to others and their property arising out of the misuse or
inability to use the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
IMPORTANT: 
obtain warranty coverage.
Troy-Bilt LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-866-840-6483, 1-330-558-7220
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Impreso en Estados Unidos de América
MaNual del operador
Medidas importantes de seguridad • Conguración • Funcionamiento • Mantenimiento • Servicio •
Solución de problemas • Garantía
ADVERTENCIA
LEA Y SIGA TODAS LAS INSTRUCCIONES DE ESTE MANUAL ANTES DE PONER EN
FUNCIONAMIENTO ESTA MÁQUINA.
SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES.
Cultivadora de dientes frontales – Serie 340
Formulario No. 769-08539
(Octubre 15, 2012)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Troy-Bilt 21A34M8711 User manual

Category
Mini tillers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages