Fanimation Hugh FPS8332 FPS8355 HUGH User manual

Español p. 18

MODEL #FPS8332**

MODEL #FPS8355**

HUGH 52

™

CEILING FAN

HUGH 44

™

CEILING FAN

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-567-2055, 8 a.m.-5 p.m., EST, Monday-Friday.

ATTACH YOUR RECEIPT HERE

READ AND SAVE THESE INSTRUCTIONS

Purchase Date

FPS8332** Net Weight 13.89 lbs (6.30 kg)

FPS8355** Net Weight 16.53 lbs (7.50 kg)

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during

the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned

to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or

reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to

defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser

will be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or

reinstallation and shipping of the product for repairs or replacement.

3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we

will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.

4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding,

tarnishing, or peeling.

5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of

heat or humidity, or as a result of any modification to the original product.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan

or Fanimation.

7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac-

company authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid

damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or

implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and

fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation

will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance,

except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary

from state to state.

10. A certain amount of wobble is normal and should not be considered a problem or a defect.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such

as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before

servicing.

4. Do not insert anything into the fan blades while the fan is operating.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan

must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed

electrician.

3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. See page 6 of owner’s manual for

support requirements. Consult a qualified electrician if in doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical

knowledge or experience, have your fan installed by licensed electrician.

WARNING: TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE ISOLATING WALL

CONTROL/SWITCH.

WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for

use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property

damage.

WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,

balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

6. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to

ensure that they do not play with the appliance.

7. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a grounded

conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be connected to an ungrounded

conductor power supply. If the conductor of a fan is identified for equipment grounding, then it should be connected to an

equipment grounding conductor.

6. This fan is to be used in wet locations.

Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .4

Electrical and Structural Requirements . . . . . . . . . . . . . . . . . .4

How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .6

How to Wire Your Ceiling Fan- Wall Conrtol . . . . . . . . . . . . . . .

Table of Contents

7

How to Assemble Your Light Kit . . . . . . . . . . . . . . . . . . . . . . .

How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .12

How to Install Your Wall Control. . . . . . . . . . . . . . . . . . . . . . . . .8

FPS8355 Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . .16

FPS8332 Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . .15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

How to Clean Your Ceiling Fan Blades. . . . . . . . . . . . . . . . . . .12

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .8

How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . 8

How to Assemble Your Ceiling Fan Blades . . . . . . . . . . . . . . .

9

10

This manual is designed to make it as easy as possible for you

to assemble, install, operate, and maintain your ceiling fan

Unpacking Instructions

For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all

Wiring outlet box and box connectors must be of type

required by local code. The minimum wire would be a 3-

conductor (2-wire with ground) of the following size:

NOTE: Place the parts from the loose parts bags in a small

container to keep them from being lost. If any parts are missing,

contact your local retailer.

Tools Needed for Assembly Materials

Wire Size A.W.G.Installed Wire Length

14

12

Up to 50 ft.

50 - 100 ft.

NOTE: If you are uncertain of part description, refer to

exploded view illustration. (Figure 1, page 15& 16)

3

1. Check to see that you have received the following

parts:

Ceiling Bracket Assembly

Ceiling Bracket Gasket

Fan Motor Assembly

(FPS8332 / FPS8355)

Light Kit/Glass Assembly

Upper LED Plate Assembly

Lower LED Plate Assembly

Plastic Cap Assembly

Light Kit Wire Cover

Blade Set 52˝

(FPS8355)

Blade Set 44˝

(FPS8332)

Four wire connectors

(supplied)

– Four Wire Connectors

– Blade Plate (FPS8355 only)

– Ten Flat Washer (FPS8332 only)

– Ten #8-32 Serrated head screws

– 4˝ Phillips Screwdriver

WARNING

Do not install or use fan if any part is damaged or

missing. This product is designed to use only those

parts supplied with this product and/or any accessories

designated specifically for use with this product by

Fanimation. Substitution of parts or accessories not

designated for use with this product by Fanimation could

result in personal injury or property damage. Contact

your retail store for missing or damaged parts.

WARNING

Before assembling your ceiling fan, refer to section on

proper method of wiring your fan (page 9). If you feel you

do not have enough wiring knowledge or experience,

have your fan installed by a licensed electrician.

Hardware bags

(FPS8332 / FPS8355)

• Wall Control

• Hardware bags:

(FPS8332 / FPS8355)

• Ceiling Bracket Gasket

• Ceiling Bracket Assembly

• Fan Motor Assembly

(FPS8332 / FPS8355)

• Blade Set

(FPS8332 / FPS8355)

• Upper LED Plate Assembly

(FPS8332 / FPS8355)

• Lower LED Plate Assembly

• Light Kit/Glass Assembly

• Light Kit Wire Cover

• Plastic Cap Assembly

Wall Control

(FPS8332 / FPS8355)

– Two #8-32 Junction box screws,

– Two Flat Washer, stainless steel

stainless steel

4

Energy Efficient Use of Ceiling Fans

Ceiling fan performance and energy savings rely

heavily on the proper installation and use of the ceiling

fan. Here are a few tips to ensure efficient product

performance.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the middle

of the room and at least 7 feet above the floor and 18

inches from the walls. If ceiling height allows, install the fan

8 - 9 feet above the floor for optimal airflow. Consult your

Fanimation Retailer for optional mounting accessories.

Turn Off When Not in the Room

Ceiling fans cool people, not rooms. If the room is

unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round

Summer Season: Use the ceiling fan in the counter-

clockwise direction. The airflow produced by the ceiling

fan creates a wind-chill effect, making you “feel” cooler.

Select a fan speed that provides a comfortable breeze,

lower speeds consume less energy.

Winter Season: Reverse the motor and operate the ceiling

fan at low speed in the clockwise direction. This produces

a gentle updraft, which forces warm air near the ceiling

down into the occupied space.Remember to adjust your

thermostat when using your ceiling fan - additional energy

and dollar savings could be realized with this simple step!

Electrical and Structural Requirements

Your new ceiling fan will require a grounded electrical

supply line of 120 volts AC, 60 HZ, 15 Amp Circuit.

Electrical code requires use of a fan-rated outlet box to

support the extra weight and motion associated with a

ceiling fan. A fan-rated box will be labeled as such and

typically supports up to a 70lb ceiling fan. Fan-Rated

Outlet Boxes vary in ratings and design. Ensure the

ratings of your ceiling fan outlet box meet the

requirements for the ceiling fan being installed. Figure 1,

Figure 2 and Figure 3 depicts different structural

configurations that may be used for mounting the

outlet box.

Low profile box (Figure 1)

joist or block. It’s used if only one cable is coming into

the box. It is also available in a saddle-mount

configuration.

CEILING

2" x 4"

CEILING JOIST

OUTLET BOX

Figure 1

Figure 2

2" x 4"

CEILING JOIST

CEILING

OUTLET BOX

Deep box (Figure 2)

between joists and is roomy enough to handle more

than one cable.

5

Electrical and Structural Requirements (Continued)

If your fan is to replace an existing light fixture, turn

electricity off at the main fuse box at this time and

remove the existing light fixture.

Turning off wall switch is not sufficient. To avoid

possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring. All

wiring must be in accordance with National and

Local codes and the ceiling fan must be properly

grounded as a precaution against possible electrical

shock.

WARNING

Deep box with brace (Figure 3)

Paired with a deep box, this hanger is meant to span

between two joists and takes the place of wooden

blocking.

To avoid fire or shock, follow all wiring instructions

carefully. Any electrical work not described in these

instructions should be done or approved by a

licensed electrician.

WARNING

Figure 3

CEILING JOIST

CEILING

OUTLET BOX

WARNING

To reduce the risk of fire, electric shock, or personal

injury, mount to outlet box marked acceptable for fan

support of 15.9 kg (35 lbs) or less and use mounting

screws provided with the outlet box. Most outlet boxes

commonly used for the support of luminaires are not

acceptable for fan support and may need to be

replaced, consult a qualified electrician if in doubt.

Figure 4

Motor

Assembly

Figure 3

6

How to Hang Your Ceiling Fan

WARNING

It is critical that the outlet box and the screws are

securely anchored to the building structure and capable

of withstanding a load of at least 35 lbs. Failure to verify

that the screws are properly installed could result in the

fan falling. (Figure 2)

Figure 1

WARNING

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before hanging.

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advice, as it must be

grounded for safe operation.

WARNING

The fan must be hung with at least 7´ of clearance from

floor to blades. (Figure 1)

Floor

Ceiling

No

less than

7 ft

Figure 2

NOTE: Supply wires

omitted for clarity

NOTE: Supply wires

omitted for clarity

NOTE: Supply wires

omitted for clarity

Outlet Box

1. Securely attach the ceiling junction box acceptable

for ceiling support into the building structure. Junction

box is not supplied with the fan. (Figure 2)

2. Using the ceiling junction box screws and flat

washers, securely attach the ceiling bracket gasket with

ceiling bracket assembly to the ceiling junction box as

shown. (Figure 3)

Outlet Box

x 2

FLAT WASHER

#8-32

JUNCTION BOX

SCREWS

HARDWARE USED:

3. Remove the two screws from the motor assembly,

retain the screws for later and loosen the remaining

screws. (Figure 4)

Ceiling bracket

Gasket

Ceiling bracket

Assembly

7

How to Hang Your Ceiling Fan (continued)

Figure 5

Ceiling Bracket

Assembly

Motor

Assembly

4. Hang the Motor Assembly as shown. (Figure 5)

You can now proceed with the electrical wiring of

your fan.

Figure 1

Figure 2

MAIN FUSE BOX

NOTE:

If you are not sure if the outlet box is

grounded, contact a licensed electrician for advice, as

it must be grounded for safe operation.

How to Wire Your Ceiling Fan - Wall Control

If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by

a licensed electrician.

▲

WARNING

To avoid possible electrical shock, be sure electricityis

turned off at the main fuse box before wiring (Figure 1).

NOTE: Supply wires

omitted for clarity

1. Disconnect the power and remove the existing

wall plate and switch.

2. Set the knob and light switch of the wall-mounted

control in the off (0) position.

3. Make wire connections and secure with wire nuts

supplied. (Figure 2)

Connect the Black wire (AC IN L) from the

wall-mounted control with the wire from the A. C.

power supply.

Connect the White wire from the ceiling fan to

the A. C. power supply.

Connect the Black wire (To Motor L) from the

wall-mounted control with the Black wire from the

ceiling fan.

Connect the Blue wire (To Light) from the

wall-mounted control with the Blue wire from the

ceiling fan.

Connect the green/yellow wire from the

wall-mounted control with ceiling fan and ground wire

from the A. C. power supply.

WARNING

Black

White

Ground

Green

Blue

Green/Yellow

120V AC

SUPPLY

SOURCE

AC IN L

To Light

To Motor L

▲

WARNING

To avoid possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring.

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advice, as it must be

grounded for safe operation.

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not operate

fan unless blades are in place. Noise and fan damage

could result.

NOTE:

Please set all knobs on the fan/light control in the

off (0) position before wiring.

8

Figure 1

How to Install Your Wall Control

1. Carefully push all connected wires inside wall

switch box. Secure the wall-mounted control to the

outlet box with two screws provided. Then, the face

plate attaches the wall control with two painted

screws. (Figure 1)

Outlet Box

Light

Switch

Screw

Fan Speed

Switch

How to Wire Your Ceiling Fan

x 4WIRE

CONNECTORS

HARDWARE USED:

2.

After splicing and making the wire connections, the

wires should be spread apart and turned upward with

the grounded conductor and the equipment-grounding

conductor on one side of the ceiling bracket and the

ungrounded conductor on the other side of the ceiling

bracket. (Figure 1)

Figure 1

White Wire

from Motor

White Wire

from Supply

Green Wire

from Supply

Green Wire

from Motor

Green/Yellow Wire

from Wall Control

Blue Wire

from Wall Control

Black Wire

from Wall

Control

Green Wire

from Ceiling Bracket

Blue Wire

from Motor

Black Wire

from Motor

1. Connect the green grounding lead from the ceiling

bracket to the supply grounding, from motor and from

wall control conductor (this may be a bare wire or wire

with green colored insulation). Securely connect wires

with a wire connector. Securely connect the white

wire (coming from motor) to the white supply (neutral)

wire using a wire connector. Securely connect the

black wire (coming from motor) to the black wire from

wall control using a wire connector. Securely connect

the blue wire (coming from motor) to the blue wire

from wall control using a wire connector. (Figure 1)

How to Assemble Your Ceiling Fan

1. Assemble the motor assembly to ceiling bracket

using the previously removed screws and securely

tighten all screws. (Figure 1)

2. Push the canopy trim ring up to conceal the screws,

such that the mounting tabs seat into the dimpled

grooves in the ceiling bracket midway between the

screws. (Figure 2)

Ceiling Bracket

Assembly

Figure 2

Dimpled

Groove

Canopy Trim

Ring

Mounting

Tabs(4)

Ceiling Bracket

Assembly

Motor

Assembly

Figure 1

9

How to Assemble Your Ceiling Fan Blades

Do not connect fan blades until the fan is completely

installed. Installing the fan with blades assembled

may result in damage to the fan blades.

CAUTION

NOTE: Periodically check blade hardware and

resecure if necessary.

FPS8355 HARDWARE USED:

#8-32

Serrated Head Screws

(3 each per blade)

Blade

Motor

x 9

#8-32

Serrated Head

Screw

x 3

BLADE PLATE

Blade Plate

Slide blades through slots in motor housing and attach

to the motor hub using the #8-32 serrated head screws

and blade plate. Make sure the screws securing the

blades to the motor hub are tight and are properly

seated. (

Figure 1B)

1B. For FPS8355

1A. For FPS8332

Slide blades through slots in motor housing and attach

to the motor hub using the #8-32 serrated head screws

and flat washers. Make sure the screws securing

the blades to the motor hub are tight and are properly

seated. (

Figure 1A)

#8-32

Serrated Head Screws

and Flat Washer

(3 each per blade)

Blade

Motor

Figure 1A

x 9

FLAT WASHER

FPS8332 HARDWARE USED:

x 9

#8-32

Serrated Head

Screw

Figure 1B

10

Motor

Assembly

Upper LED Plate Assembly

Figure 4

Figure 5

Figure 3

Figure 1

Light Kit

Assembly

4. Securely attach the 9-pin switch cup connector to

the wiring harness socket within the upper LED plate

assembly. (Figure 4)

5. Assemble the upper LED plate assembly to the light

kit assembly using the two key slots in the upper LED

plate assembly. Replace the third screw and securely

tighten all three screws. (Figure 5)

Motor

Light Kit

Assembly

How to Assemble Your Light Kit

1. Remove one of the three screws in the support

bracket at the bottom of the motor assembly and

retain the screw for later. Slightly loosen the

remaining two screws. (Figure 1)

3. Remove one of the three screws in the light kit

assembly and retain the screw for Step 5. Slightly

loosen the remaining two screws. (Figure 3)

2. Assemble the light kit assembly to the support

bracket using the two key slots in the light kit assembly.

Replace the third screw and securely tighten all three

screws. (Figure 2)

Motor

Light Kit Assembly

Figure 2

11

How to Assemble Your Light Kit (continued)

Plastic Cap

Assembly

6. Remove the three screws in the upper LED plate

assembly and retain the screws for later. (Figure 6)

8B .

(Option B--for use with plastic cap)

If you want to install the plastic cap and not the light kit.

Assemble the plastic cap to the light kit assembly by

twisting in a clockwise direction. (Figure 8B)

NOTE:

If you have installed your fan with the plastic cap,

skip steps 9 and 10.

10. Secure the glass to light kit assembly by twisting

in a clockwise direction. Do not over-tighten. (Figure 10)

8A. (Option A--for use with light kit)

Connect the 2 single-pin connectors from the upper LED

plate assembly to the 2 single-pin connectors from lower

LED plate assembly. (Figure 8A)

To reduce the risk of electric shock, disconnect the

electrical supply circult to the fan before installing

light kit.

CAUTION

9. Assemble the lower LED plate assembly to the upper

LED plate assembly using the preousily removed screws

and securely tighten all three screws. (Figure 9)

The light source is designed for this specific

application and can overheat if serviced by untrained

personnel. If any servicing is required, the product

should be returned to an authorized service facility

for examination or repair.

CAUTION

Light Kit

Assembly

Glass

Upper LED

Plate Assembly

Lower LED Plate

Assembly

Figure 9

Figure 10

Upper LED Plate

Assembly

Upper LED

Plate Assembly

Lower LED Plate

Assembly

7. If you want to install the light kit, skip the step

Assemble the

light kit wire cover

to the

upper LED

plate

assembly using the preousily removed screws and

securely tighten all three screws. (Figure 7)

Upper LED Plate

Assembly

Figure 6

Figure 7

Figure 8A Figure 8B

Light Kit Wire Cover

Light Kit Assembly

How to Operate Your Ceiling Fan

1. Restore electrical power to the outlet box by turning

the electricity on at the main fuse box. (Figure 1)

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not

operate fan until the blades are in place. Noise and

fan damage could result.

WARNING

MAIN FUSE BOX

Figure 1

0: Power Off

1: Low Speed

2: Medium Speed

3: High Speed

Light Switch:

Fan Speed Switch:

0: POWER OFF,

Turn switch counterclockwise to increase

light and clockwise to dim it.

Figure 2

Figure 3

2. Wall control functiolns: (Figure 2)

Season

Summer

Winter

Rotation Direction Switch Position

Clockwise

Counterclockwise

Reverse Switch Information

Right

Left

3. If airflow is desired in the opposite direction, turn

the fan off and wait for the blades to stop turning.

Remove glass or plastic cap from light kit, then slide

the reverse switch inside the light kit assembly to the

opposite position reinstall glass or plastic cap.

Turn fan on again. (Figure 3 )

Reversing

Switch

Light Kit

Assembly

12

Maintenance

Periodic cleaning of your new ceiling fan is the only

maintenance that is needed.

When cleaning, use only a soft brush or lint free cloth to

Abrasive cleaning agents are not required and should be

Periodic light dusting of the blades is recommended.

A feather duster will work best.

Avoid using water, cleansers, or harsh rags, which

CAUTION

Do not use water when cleaning your ceiling fan. It

could damage the motor or the finish and create the

possibility of electrical shock.

can

How to Clean Your Ceiling Fan Blades

13

Trouble Shooting

WARNING

For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.

Trouble Probable Cause Suggested Remedy

1. FAN WILL NOT START

1. Fuse or circuit breaker blown.

2. Loose power line connections to the fan, or loose

switch wire connections in the switch housing.

1. Check main and branch circuit fuses or circuit

breakers.

2. Check line wire connections to fan and switch wire

connections in the switch housings.

CAUTION: Make sure main power is turned off !

2. FAN SOUNDS NOISY

1. Blades not attached to fan.

2. Loose screws in motor housing.

3. Wire connectors inside housing rattling.

4. Motor noise caused by solid state variable speed

control.

1. Attach blades to fan before operating.

2. Check to make sure all screws in motor housing are

snug (not over-tight).

3. Check to make sure wire connectors in motor

housing are not rattling against each other or against

the interior wall of the housing.

CAUTION: Make sure main power is turned off !

4. Some fan motors are sensitive to signals from

solid-state variable speed controls. Solid-state controls

are not recommended, choose an alternative control

method.

3.FAN WOBBLES

EXCESSIVELY

1. Check to be sure screws which attach the fan blade

to the flywheel are tight.

2. Tighten the ceiling bracket screws to the outlet box,

and secure outlet box.

1. Screws securing fan blade to motor hub are loose.

2. Ceiling bracket and/or ceiling outlet box is not

securely fastened.

3. Reversing switch in neutral position. 3. Make sure reversing switch position is all the way

to one side.

14

Before discarding packaging materials, be certain all parts have been removed

Insert FINISH CODES (Refer to fan model number located on downrod support)

How To Order Parts

Contact your retail store for repair parts.

When ordering repair parts, always

give the following information.

Parts List

Model #FPS8332** & FPS8355**

noitpircseD# .feR

2

1

Fan Motor Assembly

Ceiling Bracket Gasket

3

4

Blade Set 44˝ (FPS8332)

Blade Set 52˝ (FPS8355)

Lower LED Plate Assembly

Light Kit/Glass Assembly

Plastic Cap Assembly

Upper LED Plate Assembly5

6

7

9

Wall Control10

11

Hardware Bags Containing:

Wire Connectors (4)

#8-32 Junction Box Screws, Stainless Steel (2)

#8-32 Serrated Head Screws (10)

Flat Washers (10) (FPS8332 only)

Blade Plate (3) (FPS8355 only)

gniniatnoCgaBerawdraHgnitnuoMedalB

Flat Washer, Stainless Steel (2)

AP835502BL

P835501BL

AMA8332**

AP833203**

AP835519

AP835520**

AP833211

AP835521**

CW60WH-8332-8355 CW60WH-8332-8355

HDWFPS8332**

FPS8332 Part #

AP835502BL

P835501BL

AMA8355**

AP835503**

AP835519

AP835520**

Light Kit Wire Cover8 P835522 P835522

AP835511

AP835521**

HDWFPS8355**

FPS8355 Part #

15

NOTE:

FPS8332**

Figure 1

6

7

9

11

5

1

2

8

10

11

Exploded-View Illustration

3

4

11

8

9

16

NOTE:

FPS8355**

Figure 1

6

7

11

5

1

2

3

4

11

10

11

Exploded-View Illustration

2016/06 V.01

10983 Bennett Parkway

Zionsville, IN 46077

Phone: 888-567-2055

Outside U.S.: 317-733-4113

FANIMATION.COM

FAX: 866-482-5215

Page is loading ...

Fanimation Hugh FPS8332 FPS8355 HUGH User manual

This manual is also suitable for

Fanimation Hugh FPS8332 FPS8355 HUGH User manual

in other languages

Related papers

Other documents