Privileg PCCI 802161 W User guide

Page is loading ...

GB17

YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT

This manual and the appliance itself provide important safety warnings, to be read and observed at all

times.

All safety warnings give specific details of the potential risk present and indicate how to reduce risk of

injury, damage and electric shock resulting from improper use of the appliance. Carefully observe the

following instructions:

- The appliance must be disconnected from the power supply before carrying out any installation work.

- Installation and maintenance must be carried out by a qualified technician, in compliance with the

manufacturer’s instructions and local safety regulations. Do not repair or replace any part of the

appliance unless specifically stated in the user manual.

- Regulations require that the appliance is earthed.

- The power cable must be long enough for connecting the appliance, once fitted in its housing, to the

power supply socket.

- For installation to comply with current safety regulations, an all-pole disconnect switch with

minimum contact gap of 3 mm must be utilized.

- Do not use multiple plug adapters or extension leads.

- Do not pull the power supply cable in order to unplug the appliance.

- The electrical components must not be accessible to the user after installation.

- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

- This appliance is designed solely for use as a domestic appliance for cooking food. No other type of

use is permitted (e.g. heating rooms). The Manufacturer declines any liability for improper use or

incorrect setting of the controls.

- The appliance is not intended for use by persons (including children) with any physical, sensory or

mental impairment, or without experience and knowledge of the appliance, unless supervised or

previously instructed in its use by those responsible for their safety.

- The accessible parts of the appliance may become very hot during use. Young children should be

kept away from the appliance and supervised to ensure that they do not play with it.

- During and after use, do not touch the heating elements or interior surfaces of the appliance - risk of

burns. Do not allow the appliance to come into contact with cloths or other flammable materials until

all the components have cooled sufficiently.

- At the end of cooking, exercise caution when opening the appliance door, letting the hot air or steam

exit gradually before accessing the oven. When the appliance door is shut, hot air is vented from the

aperture above the control panel. Do not obstruct the vent apertures.

- Use oven gloves to remove pans and accessories, taking care not to touch the heating elements.

- Do not place flammable materials in or near the appliance: a fire may break out if the appliance is

inadvertently switched on.

- Do not heat or cook sealed jars or containers in the appliance. The pressure that builds up inside

might cause the jar to explode, damaging the appliance.

- Do not use containers made of synthetic materials.

- Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat and oil.

- Never leave the appliance unattended during food drying.

- If alcoholic beverages are added when roasting or cooking cakes and sweets (for example, rum, cognac,

wine), remember that alcohol evaporates at high temperatures. As a result, there is a risk that vapours

released by the alcohol may catch fire upon coming into contact with the electrical heating element.

IMPORTANT SAFETY INSTRUCTIONS

This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves

and others.

All safety warnings are preceded by the danger symbol and the following terms:

DANGER

Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could cause serious injury.

GB18

Scrapping of household appliances

- This appliance is manufactured with recyclable or reusable materials. Scrap the appliance in

accordance with local regulations on waste disposal. Before scrapping, cut off the power cords so that

the appliances cannot be connected to the mains.

- For further information on the treatment, recovery and recycling of household electrical appliances,

contact your competent local authority, the collection service for household waste or the store where

you purchased the appliance.

Unpack the oven and make sure that the oven has not been damaged during transport and that the oven

door closes properly. In the event of problems, contact the dealer or your nearest After-sales Service. To

prevent any damage, only remove the oven from its polystyrene foam base at the time of installation.

PREPARING THE HOUSING UNIT

• Kitchen units in contact with the oven must be heat resistant (min 90°C).

• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all

wood chips and sawdust.

• After installation, the bottom of the oven must no longer be accessible.

• For correct appliance operation, do not obstruct the minimum gap between the worktop and the

upper edge of the oven.

ELECTRICAL CONNECTION

Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The

dataplate is on the front edge of the oven (visible when the door is open).

• Power cable replacement (see table below) must be carried out by a qualified electrician. Contact an

authorized service centre.

• Do not connect the oven to the power supply before connecting the oven and cooktop.

GENERAL RECOMMENDATIONS

Before use:

- Remove cardboard protection pieces, protective film and adhesive labels from accessories.

- Remove the accessories from the oven and heat it 200°C for about an hour to eliminate the smell of

the protective grease and insulating materials.

During use:

- Do not place heavy objects on the door as they could damage it.

- Do not cling to the door or hang anything from the handle.

- Do not cover the inside of the oven with aluminium foil.

- Do not pour water into the inside of a hot oven; this could damage the enamel coating.

- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.

- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become

trapped in the door.

- Never expose the oven to atmospheric agents.

INSTALLATION

Power supply cables table

N° of conductors Type of cable

1N+ ~

H05 RR-F 3 x 4 mm

2

2+ ~

H05 RR-F 3 x 4 mm

2

2N+ ~

H05 RR-F 4 x 2.5 mm

2

3N+ ~

H05 RR-F 5 x 1.5 mm

2

3+ ~

H05 RR-F 4 x 2.5 mm

2

GB19

Disposal of packaging materials

The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of

the packing must therefore be disposed of responsibly and in full compliance with local authority

regulations governing waste disposal.

Scrapping the product

- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and

Electronic Equipment (WEEE).

- By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product.

- The symbol on the product or on the accompanying documentation indicates that it should not be

treated as domestic waste but must be taken to an appropriate collection centre for the recycling of

electrical and electronic equipment.

Energy saving

- Only pre-heat the oven if specified in the cooking table or your recipe.

- Use dark lacquered or enamelled baking moulds as they absorb heat far better.

- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will

continue to cook even once the oven is switched off.

- oven, which is intended to come into contact with foodstuffs, complies with European Regulation

( ) n. 1935/2004 and has been designed, manufactured and sold in conformity with the safety

requirements of the “Low Voltage” directive 2006/95/CE (which replaces 73/23/CEE and subsequent

amendments), the protection requirements of “EMC” 2004/108/CE.

Oven not working:

• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.

• Turn off the oven and restart it to see if the fault persists.

Before calling the After-Sales Service:

1. See if you can solve the problem yourself with the help of the suggestions given in the

“Troubleshooting guide”.

2. Switch the appliance off and then on again it to see if the problem has been eliminated.

If the fault persists after the above checks, contact the nearest After-sales Service.

Always specify:

• a brief description of the fault;

• the type and exact model of the oven;

• the service number (number after the word Service on the rating plate), located on the right hand

edge of the oven cavity (visible when the oven door is open). The service number is also indicated on

the guarantee booklet;

• your full address;

• your telephone number.

If any repairs are required, contact an authorised After-sales Technical Service (to guarantee the use of

original spare parts and correct repair).

SAFEGUARDING THE ENVIRONMENT

DECLARATION OF CONFORMITY

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

GB20

Exterior of the oven

IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally

comes into contact with the appliance, clean immediately with a damp cloth.

• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the

water. Finish off with a dry cloth.

Oven interior

IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin

enamelled surfaces and the oven door glass.

• After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove

built-up dirt and stains caused by food residues (e.g. food with a high sugar content.

• Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.

• Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate

cleaning (see MAINTENANCE).

• The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean

the roof of the oven.

N.B: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.)

condensation may form on the inside of the door and around the seal. When the oven is cold, dry the

inside of the door with a cloth or sponge.

Accessories:

• Soak the accessories in water with washing up detergent immediately after use, handling them with

oven gloves if still hot.

• Food residues can be easily removed using a brush or sponge.

Cleaning the rear wall and catalytic side panels of the oven (if present):

IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven

sprays which could damage the catalytic surface and ruin its self-cleaning properties.

• Operate the oven empty with the fan-assisted function at 200°C for about one hour.

• Next, leave the appliance to cool down before removing any food residue with a sponge.

REMOVING THE DOOR

To remove the door:

1. Open the door fully.

2. Lift the catches and push them forwards as far as they will go (Fig. 1).

3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).

CLEANING

WARNING

- Do not use steam cleaners.

- Only clean the oven when it is cool to the touch.

- Disconnect the appliance from the power supply.

MAINTENANCE

WARNING

- Use protective gloves.

- Ensure the oven is cold before carrying out the following operations.

- Disconnect the appliance from the power supply.

GB21

To refit the door:

1. Insert the hinges in their seats.

2. Open the door fully.

3. Lower the two catches.

4. Close the door.

MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)

1. Remove the side accessory holder grilles.

2. Pull the heating element out a little (Fig. 3) and lower it (Fig. 4).

3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to

rest on the lateral supports.

REPLACING THE OVEN LAMP

To replace the rear lamp (if present):

1. Disconnect the oven from the power supply.

2. Unscrew the lamp cover (Fig. 5), replace the lamp (see note for lamp type) and screw the lamp cover

back on.

3. Reconnect the oven to the power supply.

To replace the side lamp (if present):

1. Disconnect the oven from the power supply.

2. Remove the side accessory holder grilles, if present.

3. Use a screwdriver to prise off the lamp cover.

4. Replace the lamp (see note for lamp type).

5. Refit the lamp cover, pushing it on firmly until it clicks into place.

6. Refit the side accessory holder grilles.

7. Reconnect the oven to the power supply.

N.B:

- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C

halogen lamps.

- Lamps are available from our After-sales Service.

IMPORTANT:

- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.

- Do not use the oven until the lamp cover has been repositioned.

Fig. 1 Fig. 2

Fig. 3 Fig. 4

Fig. 5 Fig. 6 Fig. 7 Fig. 8

GB22

FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION

1. Control panel

2. Upper heating element/grill

3. Cooling fan (not visible)

4. Dataplate (not to be removed)

5. Lamp

6. Fan

7. Turnspit (if present)

8. Lower heating element (not visible)

9. Door

10. Position of shelves (the number of shelves is indicated on the front of the oven)

11. Rear wall

N.B.:

- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.

- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a

while.

- When the oven door is opened during cooking, the heating elements switch off.

ACCESSORIES SUPPLIED

A. WIRE SHELF (1): the wire shelf can be used to grill food or as a support for pans, cake tins and other

ovenproof cooking receptacles.

B. DRIP TRAY (1): the drip tray is designed to be positioned under the wire shelf in order to collect fat or

as an oven tray for cooking meat, fish, vegetables, focaccia, etc.

C. BAKING TRAY (1): for cooking all bread and pastry products, but also roasts, fish en papillotte, etc.

D. SLIDING RUNNERS: to facilitate insertion and removal of accessories.

ACCESSORIES NOT SUPPLIED

Other accessories can be purchased separately from the After-sales Service.

INSTRUCTIONS FOR OVEN USE

Fig.A Fig.B

Fig.C Fig.D

GB23

INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN

The wire shelf and other accessories are provided with a locking mechanism to prevent their unintentional

removal.

1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).

2. Angle the wire shelf when it reaches the locking position “B” (Fig. 2).

3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3).

4. To remove the wire shelf proceed in reverse order.

The other accessories, like the drip tray and baking tray, are inserted in exactly the same way. The

protrusion on the flat surface enables the accessories to lock in place.

CONTROL PANEL DESCRIPTION

1. FUNCTION SELECTOR KNOB: On/off and function selector knob

2. THERMOSTAT KNOB: selecting the temperature

3. CONTROL KNOB FOR FRONT LEFT HOTPLATE 01...10*

4. CONTROL KNOB FOR REAR LEFT HOTPLATE 01...10*

5. CONTROL KNOB FOR REAR RIGHT HOTPLATE 01...10*

6. CONTROL KNOB FOR FRONT RIGHT HOTPLATE 01...10*

N.B.:the knobs are retractable. Press the knobs in the middle and they pop up.

7. ELECTRONIC PROGRAMMER

8. THERMOSTAT LED

* The multizone function can only be switched on for the double and triple hotplates of the cooktop.

(See cooktop functions table).

OVEN OPERATION

• Turn the selector knob to the required function.

The oven light switches on.

• Turn the thermostat knob clockwise to the required temperature.

The thermostat led lights up, switching off again when the oven reaches the selected temperature.

At the end of cooking, turn the knobs to “0”.

Fig. 1

Fig. 2 Fig. 3

3 5 6 84 1 7 2

GB24

COOKTOP OPERATION

The oven control panel features 4 adjustable knobs for cooktop operation. The cooktop control knobs are

marked with a numerical scale corresponding to different power settings, and a series of function symbols.

• Turn the control knob of the relevant hotplate clockwise to the desired power setting (see the

instructions supplied with the cooktop).

USING THE ELECTRONIC PROGRAMMER

Using the oven for the first time

Setting the time of day and the tone of the acoustic signal.

Upon connection of the oven to the mains power supply, AUTO and 0.00 flash on the display. To set the

time of day, press buttons - and + at the same time: the two central dots flash. Set the time of day using the

buttons + and -. Having selected the desired value, press the middle button. The display shows “ton 1”. To

select the desired tone, press button –. Having selected the preferred tone, press the middle button. To

change the time of day, proceed as described above.

Setting the timer

To set the timer, long-press the middle button: the display shows 0.00 and the bell symbol flashes. Set the

timer using the button + (the maximum programmable value is 23 hours and 59 minutes). The countdown

begins after a few seconds. The display shows the time of day and the bell remains lit, confirming the timer

has been set. To view the countdown and change it if necessary, press the middle button again.

Setting cooking time

After selecting the cooking mode and temperature using the knobs, press the middle button: the display

shows 0.00 and the bell symbol flashes. Press the middle button again: on the display and 0.00 appear

in sequence and AUTO flashes. Set cooking time using the buttons + and - (the maximum programmable

value is 10 hours). After a few seconds the display shows the time of day and AUTO remains lit, confirming

the setting. To view the remaining cooking time and change it if necessary, press the middle button for 2

seconds and then press it again a second time. At the end of the set time, the symbol switches off, the

alarm sounds and AUTO flashes on the display. Press any button to deactivate the alarm. Return the

functions and temperature knob to zero and press the middle button for two seconds to end cooking.

Delaying cooking end time

After selecting cooking time, press the middle button: the display shows , cooking end time and AUTO

flashing in sequence. Press the button + to view the desired cooking end time (cooking can be delayed by

a maximum of 23 hours and 59 minutes). After a few seconds the display shows the time of day, the symbol

switches off and AUTO remains lit, confirming the setting. To view cooking end time and change it if

necessary, press the middle button and then press it again twice. At the end of the countdown, the symbol

lights up and the oven proceeds with the selected cooking mode.

1. Button - : to decrease the value shown on the display

2. Button : for selecting the various settings:

a. Timer

b. Cooking time

c. Cooking end time setting

3. Button + : to increase the value shown on the display

A. The symbol

indicates that the timer function is in operation

B. The AUTO symbol confirms the setting has been made

A

U

T

O

2 31

A

B

GB25

COOKTOP FUNCTIONS TABLE (depending on model)

COOKTOP CONTROL KNOBS

GENTLE HEAT

To allow dough to rise, to soften butter taken from the fridge, to keep baby

bottles or food warm, also for making yoghurt, melting chocolate, etc.

This function is only available when the residual heat indicator is on. For this

function, make sure the residual heat indicator of the desired hotplate is on.

Turn the knob to . To deselect the function, change the position of the

knob.

HEAT

MAINTENANCE

To maintain a constant temperature of 60° until the end of cooking. To select

this function, turn the knob to .

FAST BOIL

This function is used to bring water to the boil rapidly and remains on for a

preset time. At the end of the preset time, the cooktop automatically returns

to the maximum power setting. This function can be selected even during

cooking. Important: before selecting this function, make sure the pot is

positioned on the selected hotplate in order to avoid any damage to the

cooktop surface. The stated performance values for this function are those

guaranteed for all glass ceramic cooktops. For this function, place the pot on

the selected hotplate and turn the knob to . To deselect, change the

position of the knob.

MULTIZONE

The multizone symbol on the knobs is activated only for the hotplates of the

cooktop provided with double or triple zone. These functions extend the

heating area of the cooktop to allow the use of large, oval or rectangular

pots. To switch on the double zone (if present), turn the knob to the “double

zone” symbol and then back anticlockwise to select the desired power level.

To switch on the triple zone (if present), turn the knob to the “triple zone”

symbol and then back anticlockwise to select the desired power level. The

residual heat indicator remains on to indicate that the cooktop is switched

on. Switch off by turning the knob to “0”.

GB26

OVEN FUNCTION DESCRIPTION TABLE

FUNCTIONS KNOB

OFF To stop cooking and switch off the oven.

LAMP To switch the oven interior light on/off.

CONVENTIONAL

To cook any kind of dish on one shelf only. Use the 2nd shelf. Preheat the

oven to the required temperature. The thermostat led turns off when the

oven is ready and food can be placed in it.

CONVECTION

BAKE

To cook meat and pies with liquid filling (savoury or sweet) on a single shelf,

and pizzas on one or two shelves. This function delivers an even, golden,

crisp top and base. When cooking on two levels, switch the position of the

dishes halfway through cooking to cook food more evenly. Use the 2nd shelf

to cook on one shelf only. To cook on two shelves, use the 1st and 3rd

shelves. Preheat the oven to the required temperature and place the food in

it when the set temperature is reached.

GRILL

To grill steak, kebabs and sausages; to cook vegetables au gratin and toast

bread. Place food on the 4th shelf. When grilling meat, use the drip tray to

collect the cooking juices. Position it on the 3rd shelf, adding approx. half a

litre of water. Preheat the oven for 3 - 5 min. During cooking the oven door

must remain closed.

TURBO GRILL

To roast large joints of meat (legs, roast beef, chickens). Position the food on

the middle shelves. Use the drip tray to collect the cooking juices. Position it

on the 1st/2nd shelf, adding approx. half a litre of water. It is advisable to

turn the meat over during cooking for more even browning. The oven does

not have to be preheated. During cooking the oven door must remain

closed.

DEFROST

To speed up defrosting of food. Place food on the middle shelf. Leave food in

its packaging in order to prevent it from drying out on the outside.

TURBOFAN

For food with a crisp base and soft top. Ideal for cooking cakes with liquid

filling and no precooked base (e.g. tarts, plum cakes, ricotta cakes as well as

pizzas with abundant topping) on a single shelf. Place food on the 2nd shelf.

Preheat the oven before cooking.

This function is also ideal for frozen convenience foods (e.g. pizzas, chips,

strudel, lasagna). Follow the instructions on the product packaging.

FORCED AIR

To cook a variety of food requiring the same cooking temperature on a

maximum of two shelves at the same time (e.g.: fish, vegetables, cakes). This

function can be used to cook different foods without odours being

transferred from one food to another. Use the 2nd shelf to cook on one shelf

only. To cook on two shelves, use the 1st and 3rd shelves, preheating the

oven first.

BOTTOM

HEATING

ELEMENT + FAN

To finish cooking food with a very liquid consistency and to obtain crisp,

golden bases. Also useful for thickening sauces. Place food on the 2nd shelf.

The oven does not have to be preheated.

BOTTOM

HEATING

For browning the base of dishes at the end of cooking. Place food on the 1st/

2nd shelf. This function can also be used for slow cooking, e.g. meat or

vegetable stews; in this case, use the 2nd shelf. The oven does not have to be

preheated.

GB27

COOKING TABLE

Recipe

Function Pre-

heating

Shelf (from

bottom)

Tempera-

ture (°C)

Time

(min)

Accessories

Leavened cakes

Yes 2 150-175 35-90 Cake tin on wire shelf

Yes 1-3 150-170 30-90

Shelf 3: cake tin on wire

shelf

Shelf 1: cake tin on wire

shelf

Filled pies

(cheesecake, strudel,

apple pie)

Yes 2 150-190 30-85

Drip tray/ baking tray or

cake tin on wire shelf

Yes 1-3 150-190 35-90

Shelf 3: cake tin on wire

shelf

Shelf 1: cake tin on wire

shelf

Biscuits/Tartlets

Yes 2 160-175 20-45 Drip tray / baking tray

Yes 1-3 150-175 20-45

Shelf 3: grill

Shelf 1: drip tray / baking

tray

Choux buns

Yes 2 175-200 30-40 Drip tray / baking tray

Yes 1-3 170-190 35-45

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray / baking

tray

Meringues

Yes 2 100 110-150 Drip tray / baking tray

Yes 1-3 100 130-150

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray / baking

tray

Bread / Pizza /

Focaccia

Yes 2 225-250 12-50 Drip tray / baking tray

Yes 1-3 225-250 25-50

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray / baking

tray

Frozen pizza

Yes 2 250 10-15

Shelf 2: drip tray / baking

tray or wire shelf

Yes 1-3 250 10-20

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray / baking

tray

GB28

Savoury pies

(vegetable pie,

quiche)

Yes 2 175-200 40-50 Cake tin on wire shelf

Yes 1-3 175-190 55-65

Shelf 3: cake tin on wire

shelf

Shelf 1: cake tin on wire

shelf

Vols-au-vent / Puff

pastry crackers

Yes 2 175-200 20-30 Drip tray / baking tray

Yes 1-3 175-200 25-45

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray / baking

tray

Lasagne / Baked pasta

/ Cannelloni / Flans

Yes 2 200 45-55 Oven tray on wire shelf

Lamb / Veal / Beef /

Pork 1 Kg

Yes 2 200 80-110

Drip tray or oven tray on

wire shelf

Chicken / Rabbit /

Duck 1 Kg

Yes 2 200 50-100

Drip tray or oven tray on

wire shelf

Turkey / Goose 3 Kg Yes 1/2 200 80-130

Drip tray or oven tray on

wire shelf

Baked fish / en

papillote (fillet,

whole)

Yes 2 175-200 40-60

Drip tray or oven tray on

wire shelf

Stuffed vegetables

(tomatoes,

courgettes,

aubergines)

Yes 2 175-200 50-60 Oven tray on wire shelf

Toa st Yes 4 200 3-5 Wire shelf

Fish fillets / steaks Yes 4 200 20-30

Shelf 3: wire tray (turn

food halfway through

cooking)

Shelf 2: drip tray with

water

Sausages / Kebabs /

Spare ribs /

Hamburgers

Yes 4 200 30-40

Shelf 4: wire shelf (turn

food halfway through

cooking)

Shelf 3: drip tray with

water

Roast chicken 1-1.3 Kg - 2 200 55-70

Shelf 2: wire shelf (turn

food two thirds of the

way through cooking if

necessary)

Shelf 1: drip tray with

water

Recipe

Function Pre-

heating

Shelf (from

bottom)

Tempera-

ture (°C)

Time

(min)

Accessories

GB29

Roast Beef rare 1 Kg - 2 200 35-45

Oven tray on wire shelf

(turn food two thirds of

the way through

cooking if necessary)

Leg of lamb / Shanks - 2 200 60-90

Drip tray or oven tray on

wire shelf (turn food two

thirds of the way

through cooking if

necessary)

Roast potatoes - 2 200 45-55

Drip-tray / baking tray (if

necessary, turn food two

thirds of the way

through cooking)

Vegetable gratin - 2 200 20-30 Oven tray on wire shelf

Lasagna & Meat Yes 1-3 200 50-100

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray or oven

tray on wire shelf

Meat & Potatoes Yes 1-3 200 45-100

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray or oven

tray on wire shelf

Fish & Vegetables Yes 1-3 175 30-50

Shelf 3: oven tray on wire

shelf

Shelf 1: drip tray or oven

tray on wire shelf

Recipe

Function Pre-

heating

Shelf (from

bottom)

Tempera-

ture (°C)

Time

(min)

Accessories

GB30

How to read the cooking table

The table indicates the best function to use for any given food, to be cooked on one or more shelves at the

same time. Cooking times start from the moment food is placed in the oven, excluding pre-heating (where

required). Cooking temperatures and times are purely for guidance and will depend on the amount of food

and type of accessory used. Use the lowest recommended values to begin with and, if the food is not

cooked enough, then move on to higher values. Use the accessories supplied and preferably dark coloured

metal cake tins and oven trays. You can also use pans and accessories in pyrex or stoneware, but bear in

mind that cooking times will be slightly longer. To obtain best results, carefully follow the advice given in

the cooking table for the choice of accessories (supplied) to be placed on the various shelves.

Cooking different foods at the same time

Using the “CONVECTION BAKE” function, you can cook different foods which require the same cooking

temperature at the same time (for example: fish and vegetables), using different shelves. Remove the food

which requires less cooking time and leave food which requires longer cooking time in the oven.

Desserts

- Cook delicate desserts with the conventional function on one shelf only. Use dark coloured metal

cake tins and always position them on the wire shelf supplied. To cook on more than one shelf, select

the forced air function and stagger the position of the cake tins on the shelves, aiding optimum

circulation of the hot air.

- To check whether a raising cake is cooked, insert a wooden toothpick into the centre of the cake. If

the toothpick comes out clean, the cake is ready.

- If using non-stick cake tins, do not butter the edges as the cake may not rise evenly around the edges.

- If the cake “sinks” during cooking, set a lower temperature the next time, perhaps reducing the

amount of liquid in the mixture and mixing more gently.

- For sweets with moist fillings (cheesecake or fruit pies) use the “CONVECTION BAKE” function. If the

base of the cake is soggy, lower the shelf and sprinkle the bottom of the cake with breadcrumbs or

biscuit crumbs before adding the filling.

Meat

- Use any kind of oven tray or pyrex dish suited to the size of the piece of meat being cooked. For roast

joints, it is best to add some stock to the bottom of the pan, basting the meat during cooking for

added flavour. When the roast is ready, let it rest in the oven for another 10-15 minutes, or wrap it in

aluminium foil.

- When you want to grill meat, choose cuts with an even thickness all over in order to achieve uniform

cooking results. Very thick pieces of meat require longer cooking times. To prevent the meat from

burning on the outside, lower the position of the wire shelf, keeping the food farther away from the

grill. Turn the meat two thirds of the way through cooking.

To collect the cooking juices it is advisable to place a drip-tray with half a litre of water directly under the

grill on which the meat is placed. Top-up when necessary.

Turnspit (only in some models)

Use this accessory to evenly roast large pieces of meat and poultry. Place the meat on the rotisserie rod,

tying it with string if chicken, and check that it is secure before inserting the rod in the seat located on the

front wall of the oven and resting it on the respective support. To prevent smoke and to collect cooking

juices, it is advisable to place a drip-tray with half a litre of water on the first level. The rod has a plastic

handle which must be removed before starting to cook, and used at the end of cooking to avoid burns

when taking the food out of the oven.

Pizza

Lightly grease the trays to ensure the pizza has a crispy base. Scatter the mozzarella over the pizza two

thirds of the way through cooking.

RECOMMENDED USE AND TIPS

Page is loading ...

Printed in Italy

09/2011

5019 610 01261

FR NLDE GB

Privileg PCCI 802161 W User guide

This manual is also suitable for

Privileg PCCI 802161 W User guide

in other languages

Related papers

Other documents