JVC GR-AXM2 User manual

Category
Camcorders
Type
User manual
GR-AXM2
COMPACT VHS CAMCORDER
INSTRUCTIONS
LYT0002-0K5A
Compact VHS
For Customer Use:
Enter below the Model No. and Serial
No. which is located on the bottom of
cabinet. Retain this information for
future reference.
Model No.
Serial No.
2 EN
Dear Customer,
Thank you for purchasing the JVC Compact VHS
camcorder. Before use, please read the safety
information and precautions contained in the
following pages to ensure safe use of your new
camcorder.
Using This Instruction Manual
All major sections and subsections are listed in the
Table Of Contents (
Z pg. 7).
Notes appear after most subsections. Be sure to read
these as well.
Basic and advanced features/operation are separated
for easier reference.
It is recommended that you . . .
...... refer to the Index (Z pgs. 43 – 46) and
familiarize yourself with button locations, etc.
before use.
...... read thoroughly the Safety Precautions and Safety
Instructions that follow. They contain extremely
important information regarding the safe use of
your new camcorder.
SAFETY
PRECAUTIONS
The AA-V11U AC Power Adapter/Charger should
be used with:
AC 120 V`, 60 Hz in the USA and Canada,
AC 110 – 240 V`, 50/60 Hz in other countries.
CAUTION (applies to the AA-V11U)
TO PREVENT ELECTRIC SHOCK MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION (s’applique à l’AA-V11U)
POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE
LA PRISE ET POUSSER JUSQU’AU FOND.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR
MOISTURE.
Warning on lithium battery
The battery used in this device may present a fire
or chemical burn hazard if mistreated. Do not
recharge, disassemble, heat above 100°C (212°F)
or incinerate.
Replace the battery with Panasonic (Matsushita
Electric), Sanyo or Maxell CR2025; use of another
battery may present a risk of fire or explosion.
n Dispose of used battery promptly.
n Keep away from children.
n Do not disassemble and do not dispose of in fire.
NOTES:
The rating plate (serial number plate) and safety
caution are on the bottom and/or the back of the
main unit.
The rating plate (serial number plate) of the AC
Power Adapter/Charger is on its bottom.
This Class B digital apparatus meets all require-
ments of the Canadian Interference – Causing
Equipment Regulations.
“Cet appareil numérique de la classe B respecte
toutes les exigences du Règlement sur le matériel
brouilleur du Canada.”
This camcorder is designed to be used with NTSC-
type color television signals. It cannot be used for
playback with a television of a different standard.
However, live recording and viewfinder playback
are possible anywhere. Use the BN-V11U/V12U/
V22U/V25U battery packs and, to recharge them,
the provided multi-voltage AC Power Adapter/
Charger. (An appropriate conversion adapter may
be necessary to accommodate different designs of
AC outlets in different countries.)
ATTENTION:
The product that you have purchased is powered
by a rechargeable battery. The battery is recycla-
ble. At the end of its useful life, under various state
and local laws, it may be illegal to dispose of this
battery into the municipal waste stream. Check
with your local solid waste officials for details in
your area for recycling options or proper disposal.
You are recommended to carefully read the cautions
on pages 47 and 48 before use.
EN 3
5. Ventilation
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the product
and to protect it from overheating, these openings must
not be blocked or covered.
Do not block the openings by placing the product on
a bed, sofa, rug or other similar surface.
Do not place the product in a built-in installation
such as a bookcase or rack unless proper ventilation
is provided or the manufacturers instructions have
been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to
the product, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding
of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes, and
requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and
power-line surges.
3. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Electrical energy can perform many useful func-
tions. But improper use can result in potential
electrical shock or fire hazards. This product has
been engineered and
manufactured to assure your personal safety. In
order not to defeat the built-in safeguards, observe
the following basic rules for its installation, use and
servicing.
ATTENTION:
Follow and obey all warnings and instructions
marked on your product and its operating instruc-
tions. For your safety, please read all the safety and
operating instructions before you operate this
product and keep this manual for future reference.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature.
If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
(B) Your product may be equipped with a 3-wire
grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety
feature.
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding-type plug.
2. Power Sources
Operate your product only from the type of power
source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult
your product dealer or local power company. If your
product is intended to operate from battery power, or
other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a
risk of fire or electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the product.
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 
810-20)
GROUNDING 
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
ELECTRIC SERVICE
EQUIPMENT
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
GROUND CLAMP
4 EN
USE
1. Accessories
To avoid personal injury:
Do not place this product on an unstable cart,
stand, tripod, bracket or table. It may fall, causing
serious injury to a child or adult, and serious
damage to the product.
Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer or sold
with the product.
Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s
instructions for any mounting of the product.
Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combina-
tion to overturn.
3. Water and Moisture
Do not use this product
near water—for example,
near a bath tub, wash
bowl, kitchen sink or
laundry tub, in a wet
basement, or near a
swimming pool and the
like.
4. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any
kind on the product.
5. Attachments
Do not use attachments not recommended by the
manufacturer of this product as they may cause
hazards.
6. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
SERVICING
1. Servicing
If your product is not operating correctly or exhibits
a marked change in performance and you are
unable to restore normal operation by following the
detailed procedure in its operating instructions, do
not attempt to service it yourself as opening or
removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to
qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or damaged in
any way.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
other hazards.
4. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in safe
operating condition.
PORTABLE CART WARNING
(Symbol provided by RETAC)
EN 5
3
4
2
1
1
3
2
Using the battery pack
1
Hook-on the battery pack's top end to the
camcorder. (Charging procedure, Z pg. 8)
2 Push in the battery pack until it locks into
place.
To remove the battery pack
Slide BATT. RELEASE and pull out the battery
pack.
QUICK OPERATION GUIDE
1 Set the power switch to “PLAY”.
2 Press REW.
— The tape will automatically stop at the
beginning of the tape.
3 Press PLAY/PAUSE.
— Playback starts and the playback picture
appears in the viewfinder or the LCD
monitor.
To stop playback, press STOP.
(For more details,
Z pg. 32.)
The viewfinder switches off automatically to
save power when the LCD monitor is opened
at an angle of over 45 degrees.
The LCD monitor turns on/off when it is
opened/closed at approx. 45 degrees.
Or simply play back the tape on a VHS VCR
using the Cassette Adapter (VHS Playpak).
Z pg. 35
1 Slide the LENS COVER open/close knob to
open the lens cover.
2 Set the power switch to “CAMERA”.
— The power indicator will light and an
image will appear in the LCD monitor or
the viewfinder.
3 Press the Recording Start/Stop button.
— Recording starts.
To stop recording temporarily, momentarily
press the Recording Start/Stop button once
again.
(For more details, Z pg. 15, 16)
The viewfinder switches off automatically to
save power when the LCD monitor is
opened at an angle of over 45 degrees.
The LCD monitor turns on/off when it is
opened/closed at approx. 45 degrees.
SUPPLY POWER
INSERTING A VIDEO
CASSETTE
PLAYBACK
SHOOTING
1 Slide MONITOR OPEN to open the LCD
monitor.
Open to an angle of over 45 degrees.
2 Press EJECT to open the cassette holder.
3 Insert a video cassette.
4 Press PUSH to close the cassette holder.
(For more details, Z pg. 13)
3
2
1
PLAY/PAUSE
STOP
REW
2
1
Hook on.
Push in.
BATT. RELEASE
Set to “PLAY”
LENS COVER
open/close knob
Recording Start/Stop button
Set to “CAMERA”
MONITOR OPEN
EJECT
PUSH
6 EN
MAJOR FEATURES
REMEMBER
Program AE with Special
Effects (
Z pg. 20)
n Auto Mode Lock
n Auto Mode Release
n Electronic Fog Filter
n ND Effect
n Sepia
n Twilight
n Sports
n 1/1000 sec. High Speed Shutter
n 1/2000 sec. High Speed Shutter
Random Assemble Editing
(
Z pg. 37 – 39)
PROVIDED ACCESSORIES
AC Power Adapter/
Charger AA-V11U
Cassettes marked can be used with this camcorder.
Variable-Speed Hyper Zoom
(
Z pg. 18)
Zoom-in
Zoom-out
LCD Color Monitor (Z pg. 16)
The Logical Choice
The only compact video
cassettes that can be
used with your VHS VCR*
8
8
2
2
5
5
4
4
1
1
6
6
3
3
7
7
180°
90°
Cassette Adapter
(VHS PlayPak) C-P7U
DC CordBattery Pack
BN-V11U
Shoulder StrapLithium Battery CR2025
EN 7
CONTENTS
GETTING STARTED
8
Power..................................................................................... 8
Clock (Lithium) Battery Insertion/Removal........................................ 10
Viewfinder Adjustment ............................................................... 10
Date/Time Setting .................................................................... 11
Tape Length Setting ................................................................... 12
Recording Mode Setting .............................................................. 12
Loading/Unloading A Cassette ...................................................... 13
Grip Adjustment ....................................................................... 14
Shoulder Strap Attachment........................................................... 14
Tripod Mounting ....................................................................... 14
RECORDING
15
Basic Recording ........................................................................ 15
Basic Features.......................................................................... 18
Advanced Features .................................................................... 20
PLAYBACK
32
Basic Playback ......................................................................... 32
Features ................................................................................ 33
Basic Connections...................................................................... 34
Using The Cassette Adapter.......................................................... 35
EDITING
36
Tape Dubbing........................................................................... 36
Random Assemble Editing (R.A.Edit)................................................ 37
USER MAINTENANCE
40
TROUBLESHOOTING
41
INDEX
43
LCD monitor/Viewfinder ............................................................. 43
Controls................................................................................. 44
Connectors.............................................................................. 44
Indicators ............................................................................... 44
Other Parts............................................................................. 44
Terms .................................................................................... 46
CAUTIONS
47
SPECIFICATIONS
49
OPTIONAL ACCESSORIES
49
ESPAÑOL
50
FOR SERVICING
52
WARRANTY
53
GETTING STARTED
RECORDING
PLAYBACKEDITING
8 EN
GETTING STARTED
**REFRESH
The AC power adapter features a REFRESH
function that allows you to fully discharge the
battery pack before recharging.
To discharge the battery . . .
..... attach the battery pack to the adapter as
shown in the above illustration. Then push
REFRESH. The REFRESH indicator lights
when discharging starts, and goes out
when discharging is complete.
Power
This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power.
NOTES:
No function is available without power supply.
Use only specified power supply.
Do not use provided power supply units with other
equipment.
CHARGING THE BATTERY PACK
SUPPLY POWER
1
Connect the charger’s AC power cord to a wall
outlet. The power indicator lights.
ATTACH BATTERY PACK
2
Align the marks and slide the battery pack in the
direction of the arrow until it locks in place.
The CHG. indicator lights.
DETACH BATTERY PACK
3
When charging is completed, the END indicator
lights. Slide the battery pack opposite the direction of
the arrow.
USING THE BATTERY PACK
ATTACH BATTERY PACK
1
Hook its top end to the camcorder and push the
battery pack in until it locks in place.
DETACH BATTERY PACK
2
Slide BATT. RELEASE and pull out the battery pack.
BATT. PACK CHARGE DISCHARGE
BN-V11U approx. 1 hr. 10 min.
approx.
3 hrs. 30 min.
BN-V12U approx. 1 hr. 10 min.
approx.
3 hrs. 30 min.
BN-V22U approx. 2 hrs. 10 min. approx. 7 hrs.
BN-V25U approx. 2 hrs. 40 min. approx. 10 hrs.
ATTENTION:
Before detaching the power source,
make sure that the camcorders power
is turned off. Failure to do so can result
in a camcorder malfunction.
REFRESH indicatorREFRESH switch
To AC outlet
POWER
indicator
END
indicator
CHG. (charge) indicator
Marks
1
1
2
BATT. RELEASE
Hook on.
Push in.
Approximate recording time (unit: min.)
BATT. LCD monitor on/ LCD monitor off/
PACK Viewfinder off Viewfinder on
BN-V11U 50 55
BN-V12U 50 55
BN-V22U 110 120
BN-V25U 150 160
EN 9
**CHARGE MARKER
A charge marker is provided on the battery pack to
help you remember whether it has been charged or
not. Two colors are provided (red and black)—you
choose which one means charged and which
means discharged.
NOTES:
The recording time per charge is affected by such factors as the time spent in Record/Standby mode and
the frequency of zooming. It is safer to have spare battery packs.
Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully
charged battery pack.
Charging and discharging times vary according to the ambient temperature and the status of the battery
pack.
Remember to set the charge marker after charging a battery pack or after detaching a discharged one from
your camcorder.
Perform the REFRESH function after no less than 5 chargings.
High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t
allow it to discharge in container, such as a bag.
If you stop recharging or discharging part way through, make sure to remove the battery pack before
unplugging the adapter’s AC cord.
Remove the battery pack from the adapter immediately after discharging.
To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
Make sure you unplug the DC cord before charging or discharging the battery pack.
A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to
continue.
The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.
indicator should light during recharging. If not, contact your nearest JVC dealer.
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery
Charger/Adapter (connect as shown in the
illustration to the left).
NOTES:
When using the car battery, leave the engine
idling.
The optional Car Battery Charger (BH-V3U) can
also be used to charge the battery pack.
When using the optional Car Battery Charger or
Car Battery Cord (AP-V7U), refer to the respective
instruction booklet.
USING AC POWER
Use the AC Power Adapter (connect as shown in
the illustration to the left).
NOTE:
The supplied AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
DC cord
Charge marker
DC OUT
terminal
To AC outlet
To DC
in jack
AC Power
Adapter/Charger
AA-V11U
Car Battery Cord
AP-V7U (optional)
To car's
cigarette
lighter socket
Car Battery Charger/Adapter
BH-V3U (optional)
10 EN
GETTING STARTED
(cont.)
Clock (Lithium) Battery Insertion/Removal
This battery is necessary for clock operation and to
perform date/time settings.
SWITCH OFF POWER
1
Switch off the unit’s power and remove the power
supply unit.
OPEN COVER
2
Open the clock battery compartment cover while
pressing the release tab.
REMOVE BATTERY (when replacing)
3
Insert a pointed, non-metallic object between the
battery and the compartment (
A
) and pull the
battery out.
INSERT BATTERY
4
Ensuring the plus (+) side is up, insert a CR2025
lithium battery and push it in.
CLOSE COVER
5
Close the compartment cover until it clicks in place.
NOTE:
See “SAFETY PRECAUTIONS” (
Z
pg. 2) for information
on safe handling of lithium batteries.
Viewfinder Adjustment
POSITION VIEWFINDER
1
Adjust the viewfinder manually for best viewability
(see illustration at left).
SELECT MODE
2
Set the power switch to CAMERA.
ADJUST DIOPTER
3
Turn the diopter adjustment control until the
indications in the viewfinder are clearly focused.
A
1
1
2
2
3
Set POWER to “CAMERA”.
EN 11
SET
CANCEL
JAN 1.00 AM 12:00
GAIN UP S.LX
TELE MACRO OFF
INTERVAL TIMER OFF
REC TIME OFF
JLIP ID NO. 07
SET CHARACTER
DATE/TIME
END :MENU KEY
Date/Time Setting
SELECT MODE
1
First set the power switch to “CAMERA”. Turn the
PROGRAM AE select dial to any position except
AUTO LOCK.
ACCESS MENU SCREEN
2
Press MENU.
SELECT FUNCTION
3
Press to move the highlight bar down to “DATE/
TIME”, then press NEAR. The Set Date And Time
screen appears.
SET DATE/TIME
4
Press FAR or NEAR until the item you want to set
begins blinking, then press + or to until the correct
setting appears.
If you decide you want to return the date and time
to the previous settings, press FAR or NEAR to
move the highlight bar to “CANCEL”, then press
MENU.
If you’re satisfied with the settings, go on to step 5.
START CLOCK OPERATION
5
Once you’ve set the date and time, press FAR or
NEAR until “SET” begins to blink, then press MENU.
The Menu screen reappears.
CLOSE MENU
6
Press MENU.
NOTES:
To display the date and time in the LCD monitor or the
viewfinder and on a connected TV, see “Date/Time
Insert” (
Z
pg. 26).
If, in step 4, you input an invalid date (FEB 30, JUN 31,
etc.) and perform step 5, “INPUT ERROR” appears
blinking at the bottom of the screen. Press +, , FAR or
NEAR to input the correct number.
FAR
LCD monitor or viewfinder
Menu Screen
Time
12-hour indication with
AM or PM
Date
Month/Day/Year
Set Time and
Date Screen
NEAR
MENU
PROGRAM AE select dial
12 EN
SP
EP
SP
T30
T20
T30 T40
GETTING STARTED
(cont.)
Tape Length Setting
Set the tape length according to the length of the tape
used.
SET TAPE LENGTH
1
Press T20•30•40 until the required indication
appears in the LCD monitor or the veiwfinder. T20 =
20 minutes of recording time, T30 = 30 minutes,
and T40 = 40 minutes (in SP).
NOTE:
The tape remaining time (
Z
pg. 15) displayed in the
LCD monitor or the viewfinder is correct only if the
correct tape length has been selected.
Recording Mode Setting
Set depending on your preference.
SET RECORDING MODE
1
Press SP•EP button. “SP” (Standard Play) provides
higher picture and sound quality and is better for
dubbing, while “EP” (Extended Play) is more
economical, recording at 1/3 the speed of SP.
NOTE:
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
T20•30•40 tape length select button
Set POWER to “CAMERA”.
Tape length indicator
SP-EP recording
mode button
Recording mode indicator
LCD monitor or
viewfinder
EN 13
1
1
2
2
3
3
4
4
5
Loading/Unloading A Cassette
OPEN LCD MONITOR
1
Slide MONITOR OPEN and open the LCD monitor
to an angle of over 45 degrees.
OPEN CASSETTE HOLDER
2
Press EJECT until the holder opens. Do not use force
to open.
INSERT/REMOVE CASSETTE
3
Make sure the label is facing outward.
CLOSE CASSETTE HOLDER
4
Press PUSH and make sure the holder is closed and
locked.
CLOSE LCD MONITOR
5
First make sure the holder is closed. Then close the
LCD monitor.
NOTES:
Closing the LCD monitor while the cassette holder is
still open may cause damage to the LCD monitor.
A cassette holder can’t be opened unless a power
supply is attached.
Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
Make sure the Erase Protection tab is in the position
that allows recording. If not, slide the tab. Some
cassettes have removable tabs. If the tab has been
removed, cover the hole with adhesive tape.
The cassette holder can’t be opened while the
camcorder is in the record mode.
GearErase Protection
Turn to take
up slack.
14 EN
GETTING STARTED
(cont.)
Grip Adjustment
EXPAND LOOP
1
Separate the Velcro strip.
INSERT HAND
2
Pass your right hand through the loop and grasp the
grip.
ADJUST STRAP LENGTH
3
Adjust so your thumb and fingers can easily operate
the Recording Start/Stop button and Power Zoom
lever. Refasten the Velcro strip.
Shoulder Strap Attachment
ATTACH STRAP
1
Following the illustration at left, thread the strap
through the top of the eyelet 1, then fold it back
and thread it through the keeper 2, and then
through the buckle 3. Repeat the procedure to
attach the other end of the strap to the other eyelet,
making sure the strap isn’t twisted.
ADJUST LENGTH
2
Adjust as shown in the illustration at left 1, then
slide both keepers snug against the eyelets to
prevent slipping 2.
Tripod Mounting
ALIGN AND TIGHTEN
1
Align the screw and camera direction stud on the
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
2
3
2
1
1
CAUTION:
When using a tripod, be sure to open and extend
its legs fully to stabilize the camcorder. To
prevent damage to the unit caused by falling
over, do not use a small-sized tripod.
Recording Start/Stop button
EN 15
25MIN
120MIN
119MIN
3MIN
2MIN (Blinking)
1MIN (Blinking)
0MIN (Blinking)
*-
-
-MIN
(Now calculating)
RECORDING
Basic Recording
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
Power (
Z
pg. 8)
Tape Length/Recording Mode Setting (
Z
pg. 12)
Grip Adjustment (
Z
pg. 14)
LOAD A CASSETTE
1
First slide MONITOR OPEN and open the LCD
monitor to an angle of over 45 degrees.
Press EJECT to open the cassette holder, then insert
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
Shooting while watching the viewfinder
ENTER RECORD–STANDBY MODE
2
Make sure the LCD monitor is closed and locked.
Slide the LENS COVER open/close switch to open
the lens cover, then set the power switch to
CAMERA.
The power indicator lights and the camcorder
enters the Record–Standby mode.
The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.
START SHOOTING
3
Press the Recording Start/Stop button.
•The tally lamp lights while recording is in progress,
and “
REC
” appears in the viewfinder.
STOP RECORDING
4
Press the Recording Start/Stop button again to stop
recording.
The camcorder re-enters the Record-Standby
mode.
Tape remaining time indicator
Tally lamp
NOTES:
When the power switch is set to CAMERA and the LCD monitor is opened at an angle of 45 degrees or more, the
LCD monitor switches on and the viewfinder switches off automatically to save power.
A cassette holder can’t be opened unless a power supply is attached.
There may be a delay after you press EJECT until the holder opens. Do not use force.
The tape’s remaining time is displayed in the LCD monitor or the viewfinder as shown.
The indicated remaining time is approximate.
The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
The tape remaining time indicator is correct only if the correct tape length has been selected (
Z
pg. 12).
“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this condition
for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.
While shooting, pressing DISPLAY lets you remove some indiations from the screen (
Z
pg. 43).
If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations, the
camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to “CAMERA”
to turn the camcorder on again.
If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5 minutes,
recording may not start immediately.
If you’re recording on a cassette from the middle, use the RETAKE function (
Z
pg. 19) to find the end of the last
recording so you don’t erase any of it.
The LENS COVER warning blinks for about 5 seconds when the camcorder is turned on when the cover is closed.
While shooting, sound is not heard from the speaker.
Power indicator
LENS COVER
Switch
POWER
Start/Stop
DISPLAY button
16 EN
RECORDING
Basic Recording (cont.)
Shooting while watching the LCD monitor
Before the following steps, perform step 1 (Z pg. 15).
ENTER RECORD–STANDBY MODE
2
Make sure the LCD monitor is fully open. Slide the
LENS COVER open/close switch to open the lens
cover, then set the power switch to CAMERA.
The power indicator lights and the camcorder
enters the Record–Standby mode.
The scene you’re aimed at appears in the LCD
monitor, with the word “PAUSE” superimposed
upon it.
START SHOOTING
3
Tilt the LCD monitor upward/downward for best
viewability (Z pg. 17) and press the Recording
Start/Stop button.
•The tally lamp lights while recording is in progress,
and “
REC
” appears in the LCD monitor.
STOP RECORDING
4
Press the Recording Start/Stop button again to stop
recording.
The camcorder re-enters the Record-Standby
mode.
NOTES:
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, we recommend that you use the viewfinder
(
Z
pg. 15).
For other notes, refer to pg. 15.
25MIN
120MIN
119MIN
3MIN
2MIN (Blinking)
1MIN (Blinking)
0MIN (Blinking)
*-
-
-MIN
(Now calculating)
LENS COVER
Switch
POWER
Start/Stop
Power indicator
Tape remaining time indicator
MONITOR
OPEN
Tally lamp
EN 17
Journalistic shooting
In some situations different angles of shooting may be
required for more dramatic results.
OPEN LCD MONITOR
1
Make sure the LCD monitor is fully open.
TILT LCD MONITOR
2
Tilt the LCD monitor in the most convenient
direction.
The LCD monitor can rotate almost full circle
(270°: 90° downward, 180° upward).
Brightness control
You can adjust the brightness of the LCD monitor by
turning the BRIGHT dial.
ADJUST BRIGHTNESS
1
If you want to brighten the image...
Turn the dial toward “+”.
If you want to darken the image...
Turn the dial toward “”.
Self-recording
You can shoot yourself while viewing your own image in
the LCD monitor.
TILT LCD MONITOR UPWARD
1
Open the LCD monitor and tilt it upward to 180
degrees so that it faces forward.
START RECORDING
2
Point the lens toward yourself and start recording.
During self-recording, the monitor image and
indications do not appear inverted as when
viewing a mirror.
BRIGHT dial
18 EN
RECORDING
Basic Features
FEATURE: Zooming
PURPOSE: Varies the focal length of the lens
and produces the zoom in/out effect.
OPERATION:
Zoom In
1) Push the power zoom lever down
toward “T”.
Zoom Out
1) Push the lever up toward “W”.
NOTES:
The further the power zoom lever
is pushed, the faster the zoom
speed becomes.
Focusing may become unstable
during zooming. In this case, set
the zoom while in Record–
Standby, set manual focus or Focus
Lock (
Z
pgs. 22, 23), then zoom
in or out in Record mode.
Zoom-out
Zoom-in
Zoom indicator
Power zoom lever
EN 19
FEATURE: Quick Review
PURPOSE: To check the end of the last record-
ing.
OPERATION: 1) Press “ ” and release quickly
during the Record–Standby mode.
Tape is rewound for about 2
seconds and played back
automatically, then pauses in
Record–Standby mode for the
next shot.
NOTE:
Distortion may occur at start of
playback. This is normal.
FEATURE: Retake
PURPOSE: To re-record certain segments.
OPERATION: 1) Make sure the camcorder is in the
Record–Standby mode.
2) Press either RETAKE button to
reach the start point for new
recording.
Pressing “F” fast-forwards the tape
and pressing “R” reverses it.
3) Press Recording Start/Stop to start
recording.
NOTE:
Noise may appear during Retake.
This is normal.
RETAKE (R/F)
20 EN
Dial LCD monitor/
Mode
symbol Viewfinder indication
Electronic Fog Filter
Makes the picture look misty white, as when an
external fog filter is attached to the lens. Softens the
image and gives it a “fancy“ look.
ND Effect
A black mist darkens the picture, as when an ND
filter is used. Helps to counter the effects of glare on
the subject.
RECORDING
Advanced Features
Dial LCD monitor/
Mode
symbol Viewfinder indication
Auto Mode Lock
Locks the camcorder in Full Auto mode, preventing
incorrect operation due to accidental button
pressing during shooting.
In this mode the following controls are disabled;
FADE, WIDE, TITLE, DISPLAY, M.W.B (Manual
White Balance), Manual Focus, Focus Lock,
Exposure Control and MENU
Auto Mode Release
Re-enables the controls that were disabled by Auto
Mode Lock.
Auto Mode Lock
LOCK
AUTO LOCK
Auto Mode 
Release
RELEASE
AUTO RELEASE
Electronic Fog Filter
FG:FOGFG
ND EffectND:ND EFFECTND
Program AE With Special Effects
All you have to do to access any of the variety of
shooting effects is to turn the PROGRAM AE select dial.
SELECT MODE
1
Turn the PROGRAM AE select dial until the symbol
of the function you want is aligned with the mark.
The selected mode’s name and its indication are
displayed in the LCD monitor or the viewfinder for
approx. 1 second. Then the name disappears, and
only the indication remains. The mode is acti-
vated.
When Auto Mode Lock or Auto Mode Release
mode is selected, only the mode’s name is
displayed. Then the name disappears and the
mode is activated.
NOTES:
Only one effect can be engaged at a time.
The screen becomes slightly reddish when the fader
(
Z
pg. 24) is used in the Sepia mode.
The screen becomes slightly dark in the High Speed
Shutter mode. Use in well-lighted situations.
In the High Speed Shutter or Sports modes, picture
color may be adversely affected if subject is lit by
alternating discharge-type light sources such as
flourescent or mercury-vapor lights.
1
/
1
0
0
0
1
/
2
0
0
0
F
G
N
D
A
U
T
O
M
O
D
E
L
O
C
K
R
E
L
E
A
S
E
SEPIA
1 second later, the mode is activated.
After 1 sec.
LCD monitor or
viewfinder
Mark
PROGRAM AE
select dial
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

JVC GR-AXM2 User manual

Category
Camcorders
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI